nuttx/configs/nucleo-g071rb/include/board.h

223 lines
7.7 KiB
C
Raw Normal View History

/****************************************************************************
* configs/nucleo-g071rb/include/board.h
* include/arch/board/board.h
*
* Copyright (C) 2019 Gregory Nutt. All rights reserved.
* Author: Mateusz Szafoni <raiden00@railab.me>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
#ifndef __CONFIG_NUCLEO_G071RB_INCLUDE_BOARD_H
#define __CONFIG_NUCLEO_G071RB_INCLUDE_BOARD_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
# include <stdbool.h>
#endif
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* Clocking *****************************************************************/
/* HSI - Internal 16 MHz RC Oscillator
* LSI - 32 KHz RC
* HSE - 8 MHz from MCO output of ST-LINK (disabled by default)
* LSE - 32.768 kHz
*/
#define STM32_BOARD_XTAL 8000000ul
#define STM32_HSI_FREQUENCY 16000000ul
#define STM32_LSI_FREQUENCY 32000 /* Between 30kHz and 60kHz */
#define STM32_HSE_FREQUENCY STM32_BOARD_XTAL
#define STM32_LSE_FREQUENCY 32768 /* X2 on board */
/* Main PLL Configuration.
*
* PLL source is HSI = 16,000,000
*
* PLL_VCOx = (STM32_HSE_FREQUENCY / PLLM) * PLLN
* Subject to:
*
* 1 <= PLLM <= 8
* 8 <= PLLN <= 86
* 4 MHz <= PLL_IN <= 16MHz
* 64 MHz <= PLL_VCO <= 344MHz
* SYSCLK = PLLRCLK = PLL_VCO / PLLR
*
*/
/* PLL source is HSI, PLLN=50, PLLM=4
* PLLP enable, PLLQ enable, PLLR enable
*
* 2 <= PLLP <= 32
* 2 <= PLLQ <= 8
* 2 <= PLLR <= 8
*
* PLLR <= 64MHz
* PLLQ <= 128MHz
* PLLP <= 128MHz
*
* PLL_VCO = (16,000,000 / 4) * 50 = 200 MHz
*
* PLLP = PLL_VCO/4 = 200 MHz / 4 = 40 MHz
* PLLQ = PLL_VCO/4 = 200 MHz / 4 = 40 MHz
* PLLR = PLL_VCO/4 = 200 MHz / 4 = 40 MHz
*/
#define STM32_PLLCFG_PLLSRC RCC_PLLCFG_PLLSRC_HSI
#define STM32_PLLCFG_PLLCFG (RCC_PLLCFG_PLLPEN | \
RCC_PLLCFG_PLLQEN | \
RCC_PLLCFG_PLLREN)
#define STM32_PLLCFG_PLLM RCC_PLLCFG_PLLM(4)
#define STM32_PLLCFG_PLLN RCC_PLLCFG_PLLN(50)
#define STM32_PLLCFG_PLLP RCC_PLLCFG_PLLP(4)
#define STM32_PLLCFG_PLLQ RCC_PLLCFG_PLLQ(4)
#define STM32_PLLCFG_PLLR RCC_PLLCFG_PLLR(4)
#define STM32_VCO_FREQUENCY ((STM32_HSE_FREQUENCY / 2) * 50)
#define STM32_PLLP_FREQUENCY (STM32_VCO_FREQUENCY / 4)
#define STM32_PLLQ_FREQUENCY (STM32_VCO_FREQUENCY / 4)
#define STM32_PLLR_FREQUENCY (STM32_VCO_FREQUENCY / 4)
/* Use the PLL and set the SYSCLK source to be the PLLR (40MHz) */
#define STM32_SYSCLK_SW RCC_CFGR_SW_PLL
#define STM32_SYSCLK_SWS RCC_CFGR_SWS_PLL
#define STM32_SYSCLK_FREQUENCY (STM32_PLLR_FREQUENCY)
/* AHB clock (HCLK) is SYSCLK (40MHz) */
#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK
#define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY
#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY
/* APB1 clock (PCLK1) is HCLK/2 (20MHz) */
#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd2
#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/2)
/* TODO: timers */
/* LED definitions **********************************************************/
/* The Nucleo LO73RZ board has three LEDs. Two of these are controlled by
* logic on the board and are not available for software control:
*
* LD1 COM: LD1 default status is red. LD1 turns to green to indicate that
* communications are in progress between the PC and the
* ST-LINK/V2-1.
* LD3 PWR: red LED indicates that the board is powered.
*
* And one can be controlled by software:
*
* User LD2: green LED is a user LED connected to the I/O PA5 of the
* STM32LO73RZ.
*
* If CONFIG_ARCH_LEDS is not defined, then the user can control the LED in
* any way. The following definition is used to access the LED.
*/
/* LED index values for use with board_userled() */
#define BOARD_LED1 0 /* User LD2 */
#define BOARD_NLEDS 1
/* LED bits for use with board_userled_all() */
#define BOARD_LED1_BIT (1 << BOARD_LED1)
/* If CONFIG_ARCH_LEDs is defined, then NuttX will control the LED on board
* the Nucleo LO73RZ. The following definitions describe how NuttX controls
* the LED:
*
* SYMBOL Meaning LED1 state
* ------------------ ----------------------- ----------
* LED_STARTED NuttX has been started OFF
* LED_HEAPALLOCATE Heap has been allocated OFF
* LED_IRQSENABLED Interrupts enabled OFF
* LED_STACKCREATED Idle stack created ON
* LED_INIRQ In an interrupt No change
* LED_SIGNAL In a signal handler No change
* LED_ASSERTION An assertion failed No change
* LED_PANIC The system has crashed Blinking
* LED_IDLE STM32 is is sleep mode Not used
*/
#define LED_STARTED 0
#define LED_HEAPALLOCATE 0
#define LED_IRQSENABLED 0
#define LED_STACKCREATED 1
#define LED_INIRQ 2
#define LED_SIGNAL 2
#define LED_ASSERTION 2
#define LED_PANIC 1
/* Button definitions *******************************************************/
/* The Nucleo LO73RZ supports two buttons; only one button is controllable
* by software:
*
* B1 USER: user button connected to the I/O PC13 of the STM32LO73RZ.
* B2 RESET: push button connected to NRST is used to RESET the
* STM32LO73RZ.
*/
#define BUTTON_USER 0
#define NUM_BUTTONS 1
#define BUTTON_USER_BIT (1 << BUTTON_USER)
/* Alternate function pin selections ****************************************/
/* USART */
/* By default the USART2 is connected to STLINK Virtual COM Port:
* USART2_RX - PA3
* USART2_TX - PA2
*/
#define GPIO_USART2_RX GPIO_USART2_RX_1 /* PA3 */
#define GPIO_USART2_TX GPIO_USART2_TX_1 /* PA2 */
/* DMA channels *************************************************************/
/* ADC */
#define ADC1_DMA_CHAN DMACHAN_ADC1 /* DMA1_CH1 */
#endif /* __CONFIG_NUCLEO_LO73RZ_INCLUDE_BOARD_H */