2023-08-24 13:50:32 +02:00
|
|
|
================
|
|
|
|
|
ST Nucleo WL55JC
|
|
|
|
|
================
|
2022-06-07 19:11:56 +02:00
|
|
|
|
|
|
|
|
The `Nucleo-WL55JC <https://www.st.com/en/evaluation-tools/nucleo-wl55jc.html>`_
|
|
|
|
|
is a development board for the STM32WL55 SoC from ST. It features 64 I/O,
|
|
|
|
|
3 onboard LEDs and buttons, integrated stlink for easy debug and flashing
|
|
|
|
|
and on-board LoRa receiver with external antenna. NSH can be easily access
|
|
|
|
|
via virtual serial port from usb.
|
|
|
|
|
|
|
|
|
|
Features
|
|
|
|
|
========
|
|
|
|
|
|
2023-08-24 13:50:32 +02:00
|
|
|
- STM32WL55JC MCU, 256K FLASH, 64K SRAM
|
|
|
|
|
- 32768 Hz LSE crystal
|
|
|
|
|
- 32 MHz HSE crystal
|
|
|
|
|
- Embedded stlink-v3 debugger (debug/flash and virtual serial port)
|
|
|
|
|
- Reset button
|
|
|
|
|
- 3 user programmable LEDs
|
|
|
|
|
- 3 user programmable buttons
|
|
|
|
|
- Power indicator LED
|
|
|
|
|
- LoRa radio with antenna
|
|
|
|
|
- 64 Nucleo I/O
|
|
|
|
|
- Arduino compatible pinout
|
2022-06-07 19:11:56 +02:00
|
|
|
|
|
|
|
|
Pin Mapping
|
|
|
|
|
===========
|
|
|
|
|
|
|
|
|
|
Pin mapping can be altered by (de)soldering bridges, by default board
|
|
|
|
|
uses following mapping:
|
|
|
|
|
|
|
|
|
|
===== ========== ============================
|
|
|
|
|
Pin Signal Notes
|
|
|
|
|
===== ========== ============================
|
|
|
|
|
PA2 LPUART1 TX Virtual serial port over usb
|
|
|
|
|
PA3 LPUART2 RX Virtual serial port over usb
|
|
|
|
|
PB6 USART1 TX D1 on Arduino pinout
|
|
|
|
|
PB7 USART1 RX R0 on Arduino pinout
|
|
|
|
|
PA0 Button 1
|
|
|
|
|
PA1 Button 2
|
|
|
|
|
PC6 Button 3
|
|
|
|
|
PB15 Blue LED Active HIGH
|
|
|
|
|
PB11 Red LED Active HIGH
|
|
|
|
|
PB9 Green LED Active HIGH
|
|
|
|
|
===== ========== ============================
|
|
|
|
|
|
|
|
|
|
Default Peripherals Configuration
|
|
|
|
|
=================================
|
|
|
|
|
|
|
|
|
|
LED
|
|
|
|
|
---
|
|
|
|
|
|
|
|
|
|
Green and Red LEDs are used by the system at boot to show system state.
|
|
|
|
|
Once system is booted these LEDs are for user to control. When
|
|
|
|
|
CONFIG_ARCH_LEDS is set, Blue LED is reserved by OS for reporting system
|
|
|
|
|
status. When CONFIG_ARCH_LEDS is not set, OS state won't be reported on
|
|
|
|
|
any of the LEDs and all 3 LEDs are available for user right from the start.
|
|
|
|
|
|
|
|
|
|
Serial Console
|
|
|
|
|
--------------
|
|
|
|
|
|
|
|
|
|
There are 2 serial ports - USART1 and LPUART1.
|
|
|
|
|
|
|
|
|
|
USART1 is connected to arduino D0/D1 pin and LPUART is connected to
|
|
|
|
|
stlink that provides virtual serial port.
|
|
|
|
|
|
|
|
|
|
NSH is configured to use LPUART and virtual serial port. After flashing
|
|
|
|
|
you can open /dev/ttyACM0 (may change depending on your system) and nsh
|
2022-06-23 15:21:31 +02:00
|
|
|
prompt will be waiting for you there. Serial device does not disappear
|
|
|
|
|
when flashing and resetting board - it can be left opened and flashing
|
2022-06-07 19:11:56 +02:00
|
|
|
will work without problems.
|
|
|
|
|
|
|
|
|
|
Configurations
|
|
|
|
|
==============
|
|
|
|
|
|
|
|
|
|
nsh
|
|
|
|
|
---
|
|
|
|
|
|
|
|
|
|
Basic NuttShell configuration (console enabled in LPUART1, exposed via USB
|
|
|
|
|
connection, at 115200 bps 8n1).
|
|
|
|
|
|
2022-06-12 14:19:50 +02:00
|
|
|
demo
|
|
|
|
|
----
|
|
|
|
|
|
|
|
|
|
This configuration contains demonstration code and programs to show what
|
|
|
|
|
board is capable of. These programs and settings are usually absolutely
|
|
|
|
|
useless in production code and are here just to show, by example, what
|
|
|
|
|
you can do with the board.
|
|
|
|
|
|
2022-06-07 19:11:56 +02:00
|
|
|
Flash & Debug
|
|
|
|
|
=============
|
|
|
|
|
|
|
|
|
|
Both flashing and debugging are done using the embedded stlink-v3 debugger.
|
|
|
|
|
OpenOCD can be invoked in the following way to flash::
|
|
|
|
|
|
|
|
|
|
openocd -f interface/stlink.cfg -f target/stm32wlx.cfg \
|
|
|
|
|
-c "program nuttx.bin exit 0x08000000"
|
|
|
|
|
|
|
|
|
|
To debug attach openocd to stlink with command::
|
|
|
|
|
|
|
|
|
|
openocd -f interface/stlink.cfg -f target/stm32wlx.cfg
|
|
|
|
|
|
|
|
|
|
start gdb::
|
|
|
|
|
|
|
|
|
|
arm-none-eabi-gdb ./nuttx --tui
|
|
|
|
|
|
|
|
|
|
attach to gdb server::
|
|
|
|
|
|
|
|
|
|
target remote localhost:3333
|
|
|
|
|
|
|
|
|
|
(optionally) reset program and start from the very beginning::
|
|
|
|
|
|
|
|
|
|
monitor reset halt
|
|
|
|
|
|
|
|
|
|
Remember to generate debug symbol by setting CONFIG_DEBUG_SYMBOLS
|
|
|
|
|
and optionally (for more natural flow in gdb step) suppress optimization
|
|
|
|
|
by setting CONFIG_DEBUG_NOOPT.
|
