nuttx/configs/clicker2-stm32/scripts/memory.ld

101 lines
4.7 KiB
Plaintext
Raw Normal View History

/****************************************************************************
* configs/clicker2-stm32/scripts/memory.ld
*
* Copyright (C) 2017 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/* The STM32F407VG has 1024Kb of FLASH beginning at address 0x0800:0000 and
* 192Kb of SRAM. SRAM is split up into three blocks:
*
* 1) 112KB of SRAM beginning at address 0x2000:0000
* 2) 16KB of SRAM beginning at address 0x2001:c000
* 3) 64KB of CCM SRAM beginning at address 0x1000:0000
*
* When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
* where the code expects to begin execution by jumping to the entry point in
* the 0x0800:0000 address range.
*
* For MPU support, the kernel-mode NuttX section is assumed to be 128Kb of
* FLASH and 4Kb of SRAM. That is an excessive amount for the kernel which
* should fit into 64KB and, of course, can be optimized as needed (See
* also configs/clicker2-stm32/scripts/kernel-space.ld). Allowing the
* additional does permit addition debug instrumentation to be added to the
* kernel space without overflowing the partition.
*
* Alignment of the user space FLASH partition is also a critical factor:
* The user space FLASH partition will be spanned with a single region of
* size 2**n bytes. The alignment of the user-space region must be the same.
* As a consequence, as the user-space increases in size, the alignment
* requirement also increases.
*
* This alignment requirement means that the largest user space FLASH region
* you can have will be 512KB at it would have to be positioned at
* 0x08800000. If you change this address, don't forget to change the
* CONFIG_NUTTX_USERSPACE configuration setting to match and to modify
* the check in kernel/userspace.c.
*
* For the same reasons, the maximum size of the SRAM mapping is limited to
* 4KB. Both of these alignment limitations could be reduced by using
* multiple regions to map the FLASH/SDRAM range or perhaps with some
* clever use of subregions.
*
* A detailed memory map for the 112KB SRAM region is as follows:
*
* 0x20000 0000: Kernel .data region. Typical size: 0.1KB
* ------- ---- Kernel .bss region. Typical size: 1.8KB
* 0x20000 0800: Kernel IDLE thread stack (approximate). Size is
* determined by CONFIG_IDLETHREAD_STACKSIZE and
* adjustments for alignment. Typical is 1KB.
* ------- ---- Padded to 4KB
* 0x20000 1000: User .data region. Size is variable.
* ------- ---- User .bss region Size is variable.
* 0x20000 2000: Beginning of kernel heap. Size determined by
* CONFIG_MM_KERNEL_HEAPSIZE.
* ------- ---- Beginning of user heap. Can vary with other settings.
* 0x20001 c000: End+1 of CPU RAM
*/
MEMORY
{
/* 1024Kb FLASH */
kflash (rx) : ORIGIN = 0x08000000, LENGTH = 128K
uflash (rx) : ORIGIN = 0x08020000, LENGTH = 128K
xflash (rx) : ORIGIN = 0x08040000, LENGTH = 768K
/* 112Kb of contiguous SRAM */
ksram (rwx) : ORIGIN = 0x20000000, LENGTH = 4K
usram (rwx) : ORIGIN = 0x20001000, LENGTH = 4K
xsram (rwx) : ORIGIN = 0x20002000, LENGTH = 104K
}