Whenever a MTD partition is set, this change limits its size
according to the flash size, avoiding the MTD partition to be
greater than the actual flash size.
1. Adjust code to avoid PM wakelock->count less than or equal to 0.
2. Fix some document format issues.
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
These configs are changed based on below rules.
1. always enable +CONFIG_LV_USE_NUTTX=y
2. If touchpad is used, enable +CONFIG_LV_USE_NUTTX_TOUCHSCREEN=y
3. enable log by +CONFIG_LV_USE_LOG=y
4. If -CONFIG_LV_MEM_CUSTOM=y previously defined, replace it with +CONFIG_LV_USE_CLIB_MALLOC=y +CONFIG_LV_USE_CLIB_SPRINTF=y +CONFIG_LV_USE_CLIB_STRING=y
5. If -CONFIG_LV_PORT_USE_FBDEV=y, default config is for fbdev. If -CONFIG_LV_PORT_USE_LCDDEV=y, +CONFIG_LV_USE_NUTTX_LCD=y
6. Remove all -CONFIG_LV_TICK_CUSTOM=y -CONFIG_LV_TICK_CUSTOM_INCLUDE="port/lv_port_tick.h"
7. If -CONFIG_LV_PORT_LCDDEV_DOUBLE_BUFFER=y, replace it with CONFIG_LV_NUTTX_LCD_DOUBLE_BUFFER=y. For fbdev, double buffer is automatically detected.
8. If -CONFIG_LV_COLOR_16_SWAP=y, need to upgrade the LCD driver to support hardware byte order swap.
Signed-off-by: Xu Xingliang <xuxingliang@xiaomi.com>
1. pm configuration demonstrates the use of power management present on the ESP32-S3.
2. You can use the pmconfig command to test the power management, for details look at
``Documentation/platforms/xtensa/esp32s3/boards/esp32s3-devkit/index.rst``
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
The Simple Boot feature for Espressif chips is a method of booting
that doesn't depend on a 2nd stage bootloader. Its not the
intention to replace a 2nd stage bootloader such as MCUboot and
ESP-IDF bootloader, but to have a minimal and straight-forward way
of booting, and also simplify the building.
This commit also removes deprecated code and makes this bootloader
configuration as default for esp32s3 targets and removes the need
for running 'make bootloader' command for it.
Other related fix, but not directly to Simple Boot:
- Instrumentation is required to run from IRAM to support it during
initialization. `is_eco0` function also needs to run from IRAM.
- `rtc.data` section placement was fixed.
- Provide arch-defined interfaces for efuses, in order to decouple
board config level from arch-defined values.
Signed-off-by: Almir Okato <almir.okato@espressif.com>
This commit implements the common RMT driver (already available for
the other Espressif's xtensa-based devices) for ESP32.
This allows us to have a proper separation between the lower and
upper-half drivers and use the 'ws2812' example to drive WS2812 RGB
LEDs.
This commit updates the Wi-Fi and the BLE driver of ESP32. Most of
the changes rely on using the common sources and header files for
xtensa-based Espressif's SoCs.
The new Wi-Fi driver supports WPA3-SAE for both Station and SoftAP
mode. BLE's coexistence mode was enhanced according to the latest
libraries.
Please note that other sources required minor changes in order to
be compatible with the common sources.
This driver is used with QEMU, to make it possible
to use networking.
This is not the MAC in ESP32, however, it can be used with QEMU.
The code was shamelessly copied from 31dac92e5f
The board's microphone uses 24-bit i2s and this commit also fixes
the segmentation fault caused by the audio buffer overflow.
arch/xtensa/src/esp32/esp32_i2s.c: Fix bug regarding 24-bit audio and add AUDIOIOC_STOP to ioctl
drivers/audio/audio_i2s.c: Report number of channels on AUDIOIOC_GETCAPS
in boards/xtensa/esp32/esp32-sparrow-kit:
/configs/nsh/defconfig: Add I2S configs
/src/esp32-sparrow-kit.h: Add the signature of esp32_i2sdev_initialize()
/src/esp32_bringup.c: Add call to esp32_i2sdev_initialize()
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
Enable with ./tools/configure.sh -l esp32-devkitc:dac
DAC channel 0 = GPIO 25
DAC channel 1 = GPIO 26
default path: /dev/dac0
Resolution 8 bits = values 0~255
Voltage: 0~Vref
The reference voltage 'Vref' here is input from the pin VDD3P3_RTC
which ideally equals to the power supply VDD (3.3V).
- A pre-built IDF bootloader is used by default;
- `ESP32S3_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32S3_PARTITION_TABLE.
- A pre-built IDF bootloader is used by default;
- `ESP32S2_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32S2_PARTITION_TABLE.
- A pre-built IDF bootloader is used by default;
- `ESP32_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32_PARTITION_TABLE.
By integrating the Espressif`s HAL repository into the current
ESP32-S2 implementation on NuttX, it is possible to call functions
that makes it easier to setup the registers of the ESP32-S2,
enabling the usage of common Espressif drivers.
By integrating the Espressif`s HAL repository into the current
ESP32-S3 implementation on NuttX, it is possible to call functions
that make it easier to set up the registers of the ESP32-S3 and
enables the usage of common Espressif drivers. Please note that
Espressif's HAL repository was already being used for the Wi-Fi
driver. Then, this commit includes other source files to be used
by other drivers other than Wi-Fi and reorganize the build process.
The RMT (Remote Control) character driver allows to use the RMT
peripheral (usually, a one-wire peripheral dedicated to driving
IR remote control) as a character driver.
Please note that this perpiheral depends on the lower-half specific
driver implementation.
Once these messages are thrown during the system's bring-up, it is
advisable them to be output by the syslog considering the file
system initialization.
The SmartFS partition needs to be formatted before being mounted.
Otherwise, it would throw an error message. The error message now
contains a suggestion to format the partition when such an error
is detected.
