Verge Aero has submitted the SGA
Anthony Merlino has submitted the SGA
Gregory Nutt has submitted the SGA
Sebastien Lorquet has submitted the ICLA
as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
to save the preserved space(1KB) and also avoid the heap overhead
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I694073f68e1bd63960cedeea1ddec441437be025
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
xbee: Fixes one instance of the use of IOBUSER_WIRELESS_MAC802154 which isn't available without the software MAC layer. Instead we use IOBUSER_WIRELESS_RAD802154 throughout the whole driver since it is always available when IEEE 802.15.4 support is enable
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Iobinstrumentation
* mm/iob: Introduces producer/consumer id to every iob call. This is so that the calls can be instrumented to monitor the IOB resources.
* iob instrumentation - Merges producer/consumer enumeration for simpler IOB user.
* fs/procfs: Starts adding support for /proc/iobinfo
* fs/procfs: Finishes first pass of simple IOB user stastics and /proc/iobinfo entry
Approved-by: Gregory Nutt <gnutt@nuttx.org>
ieee802154: Support dynamic FCS length. Adds IEEE802154_ATTR_PHY_FCSLEN.
This change introduces IEEE802154_ATTR_PHY_FCSLEN which the radio layer can support to set/get the FCS length that's added to the end of the frame. One use case, in promiscuous mode, is to add back in the FCS of the received frame by increasing the iob->io_len by the FCS length.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Xbee getset txpwr
* drivers/wireless/ieee802154/xbee: Minor improvements to debug facilities.
* drivers/wireless/ieee802154/xbee: Add support for setting/getting tx power.
TODO: The input/output arguments from the MLME primitive are intended to be an int32_t dbm value. However this change simply reports the power level register of the XBee. Need to add look-up table to back calculate the dbm value.
# Conflicts:
# drivers/wireless/ieee802154/xbee/xbee.c
Approved-by: GregoryN <gnutt@nuttx.org>
drivers/xbee: Fixes issue with timeouts. Timeouts were in ticks but should have been in ms. This caused false triggers of timeout causing redundant packets, etc.
Approved-by: GregoryN <gnutt@nuttx.org>
Xbee: Adds a timeout to send logic to handle case where XBee module fails to respond to a Transmit request with a Transmit Status
Approved-by: Gregory Nutt <gnutt@nuttx.org>
ieee802154: Simplifies notify() and rxframe() calls to a single notify() call. dataind's and all other "notifs" are now "primitives" which aligns with standard terminology
* mac802154: Adds missing breaks from case statement
* sixlowpan: Fixes bad logic where ACK is not requested if address is not a broadcast
* ieee802154: Simplification of "notifs" and "datainds" to generic primitives passed via a single notify call to the layer above the MAC
* Directories.mk should reference CONFIG_WIRELESS instead of CONFIG_DRIVERS_WIRELESS
* xbee_netdev: Network must be locked when calling sixlowpan_input
* sixlowpan: Reassembly buffer can't be freed if provided by radio driver
* sixlowpan: Don't free IOB if there is an error processing it as the MAC will try to pass it along to another receiver
* ieee802154: Adds basic logging to ieee802154_primitive.c
* Minor fixes after rebase
* xbee: Adds AT query timeout to retry if XBee doesn't respond to request
* same70-xplained: Adds Xbee support. Makes mikroBus slot Kconfig 'choice'
* mac802154: Removes unused function declaration
* drivers/mrf24j40: Fixes compilation error using . operator rather than -> operator
* mac802154_device: Changes a few mac802154_primtive_free's to ieee802154_primitive_free() and changes notif to primitive in a couple places.
* mac802154: Adds promiscous mode logic to bypass parsing of incoming frames. MAC char device also checks for promiscous mode and passes whole frames including header and FCS to the application if promiscous mode is enabled.
* sixlowpan: Fixes logic to correctly check if packet is large enough to include header. This would cause packets to be considered too small when they are sufficiently sized.
* sixlowpan: Fixes forwarding logic to use forwarding device rather than received device to look up destination link layer address
* net/ipforward: Fixes typo that caused build error when IP forwarding was enabled with CONFIG_NET_ICMPv6_NEIGHBOR enabled as well.
* configs/same70-xplained: Simple spelling fix
Approved-by: Gregory Nutt <gnutt@nuttx.org>
drivers/xbee: Fixes a few warnings
* drivers/xbee: Fixes a few warnings
* configs/clicker2-stm32: Updates sections about i8sak usage in the README
Approved-by: Gregory Nutt <gnutt@nuttx.org>
drivers/wireless: Adds XBee S2C (802.15.4 firmware) support. XBee driver emulates mac802154 interface
* drivers/wireless/xbee: Adds xbee_netdev. Very similar to mac802154_netdev
* configs/same70-xplained: Starts adding support for XBee radio
* drivers/wireless/ieee802154/xbee: More structuring of XBee driver
* drivers/wireless/ieee802154/xbee: More Xbee work. Starts adding support on Clicker2
* drivers/wireless/ieee802154/xbee: More XBee MAC code
* configs/clicker2-stm32: More work to add XBee radio support
* drivers/wireless/ieee802154/xbee: Most of driver is now structured. No build errors
* configs/clicker2-stm32: Adjustments to XBee click module support
* drivers/xbee: Changes md_ prefix to xd_ prefix for xbeenet_driver_s fields
* drivers/xbee: XBee network device now passes MAC events via IOCTL
* drivers/xbee: Support querying device for parameters, setting parameters, and structures association/startpan logic
* configs/clicker2-stm32: Fixes Xbee lower half ATTN poll logic
* drivers/xbee: Removes dependce on CONFIG_IEEE802154_NETDEV
* drivers/xbee: Supports MAC RESET.request primitive
* drivers/xbee: Exposes generic AT query to the rest of driver
* drivers/xbee: Sets local values when writing setting change to Xbee device
* drivers/xbee: Finish association logic
* drivers/xbee: Adds xbee_get_mhrlen( ) allocating enough space for API frame header to frame
* drivers/xbee: Finishes transmit/receive logic
* drivers/xbee: Fixes xbee_netdev to match logic in mac802154_netdev.c
* drivers/xbee: Rearranges logic to prevent a loop condition where recursion could potentially occur to the point of deadlocking the system
Approved-by: Gregory Nutt <gnutt@nuttx.org>
