There is a good case on sim platform:
When we input some cmd and click enter key to start application in terminal,
this context will change to application from IDLE loop. Althrough entey key '\r'
has been received to recv buffer and complete post semaphore of reader, but
pollnotify may not be called because context change. So when application run
poll function, because no events happend and poll enter wait, context will
again change to IDLE loop, this pollnotify of IDLE loop will run to send poll
events, poll function of applicaton will wake up. It's wrong!
Change-Id: I812a889f2e90781a9c3cb4b0251cccc4d32bebd1
Signed-off-by: dongjiuzhu <dongjiuzhu1@xiaomi.com>
This adds support for the Q10 BlackBerry based keyboard
from Solder Party. https://www.solder.party/docs/keyboard-pmod/
They keyboard device registered at /dev/kbdN is fully compatible
with hidkbd and has been testing with the Keyboard FeatherWing
on the nRF52 platform.
The buttons are added as a standard discrete joystick if
optionally enabled. The PMOD variant of this does not
include these buttons, but the Keyboard FeatherWing does.
This joystick is usually defined at /dev/djoyN and
can be used with the djoy example application.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
This patch resolves to bugs in the GPIO interrupt logic:
1. Any pins did not have STMPE811_GPIO_RISING in their pincfg
would clear the rising edge interrupt enable flag for all
pins due to a masking bug.
2. Pins would never trigger a second interrupt. There is an
undocumented requirement that you have to clear both the
GPIO interrupt status register __and__ also the edge
detection status register. Failure to clear either of
these will result in no further interrupts being triggered.
This requirement exists both for edge and level modes of
operation.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
to save the preserved space(1KB) and also avoid the heap overhead
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I694073f68e1bd63960cedeea1ddec441437be025
so the lower half driver don't need include the specific board.h
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I2ff5c30049a5c5e8ee90baea56e9f4cb1a8a4f87
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is only for those files under drivers/input.
This reverts commit b9ace36fcc.
This change was added by PR 625 but has a serious logic flaw. It removes all occurrences of INCDIROPT and replaces it with a definition in tools/Config.mk:
else ifeq ($(WINTOOL),y)
DEFINE = "$(TOPDIR)/tools/define.sh"
INCDIR = "$(TOPDIR)/tools/incdir.sh" -w
This logic flaw is the Config.mk is included in all Make.defs files BEFORE WINTOOL is defined. As a result, the definition is wrong in many places when building under Cygwin with a Windows native toolchain.
This commit does two things:
1. First, it reorganizes the driver Kconfig files so that each is self contained. Before, a part of the driver configuration was in drivers/Kconfig and the rest was in in drivers/xyz/Konfig. Now, all of the driver configuration is consolitated in the latter.
2. Second, this commit correct numerous serious errors introduced in a previous reorganization of the driver Kconfig files. This was first noted by Nicholas Chin in PR270 for the case of the drivers/i2c/Kconfig but some examination indicates that the error was introduced into several other Kconfig files as well.
The nature of the introduced error was basically this:
- Nothing must intervene between the menuconfig selection and the following conditional configuration otpions.
- A previous PR erroneously introduced unconditional options between the menuconfig and the following confditional logic, thus corrupting the driver menus.
This error was easy to make because the driver Kconfig files were not well modularized. Making them fully self-contained should eliminate this kind of error in the future.
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run all .h and .c files modified in last PR through nxstyle.
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
Fix stm32l4_otgfshost.c: error: 'ret' undeclared (#32)
result by commit 6a3c2aded6
Change-Id: I68ba79417d8da102da8d91c74496961aef242dd9
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
arch/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
sched/ audio/ crypto/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
Documentation/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
fs/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
graphics/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
net/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
drivers/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
include/, syscall/, wireless/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
configs/: Remove all references to CONFIG_DISABLE_POLL. Standard POSIX poll can no longer be disabled.
libs/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
syscall/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
wireless/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
Documentation/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
include/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
drivers/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
sched/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
configs: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/xtensa: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/z80: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/x86: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/renesas and arch/risc-v: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/or1k: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/misoc: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/mips: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/avr: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/arm: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
drivers/timers/rtc.c: Support signal notification through SIGEV_THREAD
drivers/input/ajoystick.c: Support signal notification through SIGEV_THREAD
drivers/input/djoystick.c: Support signal notification through SIGEV_THREAD
drivers/input/button_upper.c: Support signal notification through SIGEV_THREAD
drivers/sensors/zerocross.c: Support signal notification through SIGEV_THREAD
drivers/wireless/ieee802154: Support signal notification through SIGEV_THREAD
drivers/lcd/ft80x.c: Support signal notification through SIGEV_THREAD
No... I was misled. The shutdown function is usually called when the
driver is unlinked. But not in this case. In this case, it is simply
called when the last reference is closed. And no, you don't want to
detach the interrupt handler in that case. My bad.
This reverts commit b79e6b9c9a.
