The ADC peripheral can only support up to
50MHz on rev V silicon and 36MHz on Y silicon.
The existing driver always used no prescaler
and kept boost setting at 0.
The 1170 usage of the GPR registers is to select the
between GPIO{2|3} or CM7_GPIO{2|3} where as the 1060
it selected ports between 1-6,2-7..4-9 and uses
different GPR registers.
For the 1170 we are defaulting to GPIO{2|3} and not
supporting the swtich to CM7_GPIO{2|3}.
Co-authored-by: Jari van Ewijk <jari.vanewijk@nxp.com>
Co-authored-by: David Sidrane <david.sidrane@nscdg.com>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
imxrt:Kconfig fix formatting
imxrt:usbphy move IMXRT_USBPHY{1|[2]}_BASE to memory map
imxrt:lpspi Fix build breakage from adding 1170
imxrt:Finish 1170 iomux and clockconfig versioning
imxrt:Remove duplicate imxrt_clock{off|all}_lpi2c4
imxrt:pmu remove duplicate dcd non 117x header
imxrt:lpspi Fix unused var warnings
imxrt:lpi2c Fix unused var warnings
imxrt:lowputs Fix unused var warnings
imxrt:imxrt117x_dmamux fix duplicate entries
imxtr:serial Use IOMUX_PULL_{UP|DOWN} and map IOMUX V1 to them
imxrt:MPU Support the 1170
imxrt:dmamux Alias IMXRT_DMAMUX0_BASE as IMXRT_DMAMUX_BASE
imx1170:ccm Alias CCM_CCGR_DMA & CCM_CCGR_SNVS_LP for compatiblity
Author: Peter van der Perk <peter.vanderperk@nxp.com>
IMXRT7 Add LPUART 9/10/11/12 support
Author: David Sidrane <david.sidrane@nscdg.com>
imxrt:1170pinmux Add QTIMER pins
imxrt:1170pinmux Add GPT pins
imxrt:1170pinmux Add FLEXPWM pins
imxrt1170:pinmap Add GPIO_ENET_1G pinning
imxrt:enet Support ENET_1G
imxrt:periphclks rt1170 does not have canX_serial clock
imxrt:flexcan:Layer imxrt_ioctl
imxrt117x:memorymap added CAN3
imxrt:ADC support ver1 and ver2 for imxrt117x
imxrt:imxrt117x_ccm Align timer naming with other imxrt QTIMERn->TIMERn
imxrt:imxrt117x_ccm align CCM names with rt106x
imxrt:XBAR support larger number of selects needed on imxrt1170
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
FlexSPI AHB Region support, PIT rename for compatiblity
imxrt:USB Analog add VBUS_VALID_3V
FlexSPI expand prefetch registers for IMXRT117X
imxrt:Support Initialization of FlexRam without Running from OCRAM
imxrt: ocotp add UNIQUE_ID register definition
imxrt: enet use ocotp unique_id
imxrt: enet fixes for imxrt117x
imxrt: ethernet pinmux sion enable
imxrt:imxrt_periphclk_configure add memory sync
Flush the pipeline to prevent bus faults, by insuring a
peripheral is clocked before being accessed on return from
this function.
imxrt:Restructure gpioN to padmux mapping
imxrt:Add imxrt1170 daisy
imxrt: correct power modes for imxrt117x fixing hang on WFI
imxrt: imxrt117x TCM MPU config
imxrt: FlexRAM clocking DIV0 setup
imxrt: 117x periphclocks wait for status bit
imxrt: iomucx set pad settings correctly and allow reconfiguration
imxrt: enet align buffers 64-byte for optimal performance
Add DSC barriers for write-through cache support
imxrt: imxrt1170 use FlexCAN FD/ECC features
imxrt:iomuxc_ver2 (117x) SD_B1 and DISP_B1 use PULL feild not PUE/PUS
imxrt:Fix 1170 SNVS addressing
imxrt: enet set mii clock after ifdown so that phy keep working
nxstyle fixes
imxrt: preprocessor and include fixes
Fix configs
imxrt1170-evk clean defconfig
in order to maintain the completeness of the matter related functional code, the build of matter is added to testlist.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
- When receiving Router Advertisement Message, if Managed Address
Configuration flag is set, we should ignore the Autonomous
Address-configuration flag, and obtain the IPv6 address via the
stateful process.
Signed-off-by: liqinhui <liqinhui@xiaomi.com>
fix build break:
/usr/bin/ld: skipping incompatible /usr/lib/gcc/x86_64-linux-gnu/11/libstdc++.so when searching for -lstdc++
/usr/bin/ld: skipping incompatible /usr/lib/gcc/x86_64-linux-gnu/11/libstdc++.a when searching for -lstdc++
/usr/bin/ld: cannot find -lstdc++: No such file or directory
/usr/bin/ld: skipping incompatible /usr/lib/gcc/x86_64-linux-gnu/11/libstdc++.so when searching for -lstdc++
collect2: error: ld returned 1 exit status
ninja: build stopped: subcommand failed.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
Fixes is stuttering output.
The use of the semaphore was causing blocking
on non blocking callers. This ensured that
the TX DAM would be restated, but when it
was switched to trywait in 660ac6, it left
data in the xmit queue unsent.
This solution removes the semaphore and restart
the DMA on completion if there is more data in
the xmit queue to be sent.
chip/sam_emac.c:3754:11: error: 'struct sam_emac_s' has no member
named 'phytype'
3754 | if (priv->phytype == SAMV7_PHY_KSZ8061)
| ^~
make[3]: *** [Makefile:167: sam_emac.o] Error 1
Member phytype is available only if CONFIG_NETDEV_PHY_IOCTL and
CONFIG_ARCH_PHY_INTERRUPT is set.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Fixes stuttering output.
The use of the semaphore was causing blocking
on non blocking callers. This ensured that
the TX DAM would be restated, but when it
was switched to trywait in 8362e314, it left
data in the xmit queue unsent.
This solution removes the semaphore and restart
the DMA on completion if there is more data in
the xmit queue to be sent.
This prevents dma stop operations called of a completion
call back from rentering, the callback and ensures that
the call back will see the idle state.
Avoid splicing paths to /include when BOARD_COMMON_DIR does not exist
and enhanced Windows native compilation
Signed-off-by: chenrun1 <chenrun1@xiaomi.com>
In this change, if board/include and board/script are not found, they will be looked for again in the upper level of common.
Signed-off-by: chenrun1 <chenrun1@xiaomi.com>
add the tools needed for the compilation environment and docker first, then add matter compilation to cilist
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
A new locking mechanism: read/write locks
When there is a writer it is not possible to put on a read lock or a write lock; when there is a reader it is possible to reenter the read lock but not the write lock.
Writers are exclusive locks, readers are shared locks.
At the same time through the waiter count to determine whether there is currently a blocked task, if there is then in the unlock time to wake up all the waiter, through the priority of the competition to complete the blocked lock execution.
For example:
When we have a reader blocking two waiter writers, when the reader is unlocked it wakes up both writers. The writer with higher priority wakes up and checks for a successful condition and locks the lock, the second writer wakes up and fails to check for a condition and continues to block the lock.
Signed-off-by: chenrun1 <chenrun1@xiaomi.com>
