sam_ili9488.c:1605:7: error: label 'errout_with_dmadog' used but not defined
bcmf_sdio.c:855:16: error: passing argument 1 of 'wd_start' from incompatible pointer type
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
to save the preserved space(1KB) and also avoid the heap overhead
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I694073f68e1bd63960cedeea1ddec441437be025
Change the preallocated message and descriptor from 32/24 to 4.
The total size is reduce from 1892 to 532
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I79d199465daef678986868f773876289859f42fc
boards: metro-m4 Add support for starting the watchdog timer on the metro-m4.
Testing:
- Build check only
Signed-off-by: Leomar Mateus Radke <leomar@falker.com.br>
since the maximum number of argument pass to wd_start in the whole
code base is 2 and change CONFIG_MAX_WDOGPARMS in some defconfig
from 1 to 2 oherwise pthread_condclockwait will fail
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ib6cb28b8c0722058849e7be916e164513431d21c
malloc() and free() should never be used within the OS. This will work in the FLAT build because there is only a single heap, but will cause problems in PROTECTED and KERNEL build modes where there are separate heaps for user and kernel memory.
Typically kmm_malloc(), kmm_zalloc(), and kmm_free() should be called within the kernel in those build modes to use the kernel heap.
Memory is never free. Possible memory leak:
./boards/arm/cxd56xx/common/src/cxd56_crashdump.c: pdump = malloc(sizeof(fullcontext_t));
Memory allocated with malloc(), but freed with kmm_free():
./drivers/usbhost/usbhost_composite.c: cfgbuffer = (FAR uint8_t *)malloc(CUSTOM_CONFIG_BUFSIZE);
Memory is never freed in these cases. It is allocated in the driver initialization logic, but there is no corresponding uninitialization logic; memory is not freed on error conditions:
./arch/arm/src/lc823450/lc823450_i2s.c: priv = (struct lc823450_i2s_s *)zalloc(sizeof(struct lc823450_i2s_s));
./arch/arm/src/sam34/sam_spi.c: spics = (struct sam_spics_s *)zalloc(sizeof(struct sam_spics_s));
./arch/arm/src/sama5/sam_spi.c: spics = (struct sam_spics_s *)zalloc(sizeof(struct sam_spics_s));
./arch/arm/src/samv7/sam_spi.c: spics = (struct sam_spics_s *)zalloc(sizeof(struct sam_spics_s));
Memory is allocated with zalloc() but freed on error conditions with kmm_free():
./arch/arm/src/sama5/sam_ssc.c: priv = (struct sam_ssc_s *)zalloc(sizeof(struct sam_ssc_s));
./arch/arm/src/samv7/sam_ssc.c: priv = (struct sam_ssc_s *)zalloc(sizeof(struct sam_ssc_s));
./arch/arm/src/stm32/stm32_i2s.c: priv = (struct stm32_i2s_s *)zalloc(sizeof(struct stm32_i2s_s));
Memory is never freed:
./drivers/spi/spi_bitbang.c: priv = (FAR struct spi_bitbang_s *)zalloc(sizeof(struct spi_bitbang_s));
Provide functions which get and set the 3A (Auto white balance/Auto
exposure/Auto
focus) parameters.
These are achieved by the ioctl request codes VIDIOC_G_EXT_CTRLS and
VIDIOC_S_EXT_CTRLS which have the following settings:
1. ctrl_class = V4L2_CTRL_CLASS_CAMERA
2. id = V4L2_CID_3A_PARAMETER
Also, provide function which get the 3A adjustment status.
This is achieved by the ioctl request codes VIDIOC_G_EXT_CTRLS which has the
following settings:
1. ctrl_class = V4L2_CTRL_CLASS_CAMERA
2. id = V4L2_CID_3A_STATUS
Fix the following three bugs about ON/OFF control of auto white balance and auto
exposure:
- The returned value of VIDIOC_G_CTRL with id = V4L2_CID_AUTO_WHITE_BALANCE is
different from V4L2 specification.
- Auto exposure is locked if auto white balance lock is requested.
- Auto exposure and auto white balance are locked if auto exposure lock is
requested.
Add imageproc_alpha_blend() to blend two images in a specified ratio.
The blended source image is selectable from the following two types:
- Single color image
- YUV422 image
The blend ratio is selectable from the following three types:
- Blend ratio with single value
- Blend ratio with 1bpp
- Blend ratio with 8bpp
Summary:
- Fix style violations in lc823450_syscontrol.h
Impact:
- This commit affects register naming in syscontrol.
- So some files such as lc823450_start.c lc823450_mux.c were also changed.
Testing:
- Build check only
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
- Add new functions of GNSS
- Support the lower PWM frequency
- Add CONFIG_CPUFREQ_RELEASE_LOCK
- Add high speed ADC support
- Add HPADC input gain configuration
- Add eMMC device
- Frame buffer support
- Fix SD/GNSS/sensor drivers not worked
- Build errors
- Fix nxstyle issues
- Add board specific logic to altair modem dirver
- Fix issue that SPI4 RX frequency violated AC Spec
- Remove dummy buffer in altair driver
- Fix priority of SPI transfer task is too low
- Remove unnecessary configuration
- Modify timeout value for RX ready
- Fix minor bugs
Kinetis: Reworked USB driver for setup out data phase.
Freedom K28: New config nshsdusb, with RNDIS support
PL2303: Try to avoid clone detection.
General: various nxstyle fixes
General: license changed
1.It make sense to let Toolchain.defs give the default value
2.The board can still change if the default isn't suitable
3.Avoid the same definition spread more than 200 Make.defs
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ic2649f1c7689bcf59c105ca8db61cad45b6e0e64
- makes nsh reboot command work
Squashed commit of the following:
commit 5193f6ae9623bfb4d3bed4ecf3d0fb9ae1bfb6e8
Author: Adam Feuer <adam@starcat.io>
Date: Thu Jul 16 16:41:54 2020 -0700
removed conflict tag that was missed
- result of an incorrectly fixed bad merge
commit 731108ea7495655e96e516448887ca8c9ab354d1
Author: Adam Feuer <adam@starcat.io>
Date: Thu Jul 16 16:12:30 2020 -0700
implement system reset to make nsh reboot work
Squashed commit of the following:
commit 245d155cc58d31af412f2b832877736b2088b896
Author: Adam Feuer <adam@starcat.io>
Date: Thu Jul 16 16:10:10 2020 -0700
add Kconfig setting for system reset
commit e7d5def8151821bf359c55c05ba1f59421b2371a
Author: Adam Feuer <adam@starcat.io>
Date: Thu Jul 16 15:51:35 2020 -0700
implement system reset to make nsh reboot work
Make.defs under board folder can still overwrite the default as needed
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I1c300a8ace4b54d475ef8d398661ed65ca273a2e
The QuickFeather board added as an initial target.
These featrues are minimally implemented:
* Clock Configuration -- All clocking registers are defined and
configuration is used to setup the HSO, M4 Core, and M4 Perif
clocks. Additionally some clock debugging is stubbed for
bringing out clock paths to IO pins.
* UART -- The lowputc as well as the serial driver is implemnted
for the single UART device. Currently the configuration is
hard coded, but uses the proper interfaces to later fill in.
* SysTick -- The system tick timer is implemented and clocking
properly. Tickless mode is not yet implemented.
* Interrupts -- The interrupt system is implemented and verified
using the UART and SysTick systems.
* GPIO -- GPIO and IOMUX systems are defined and implemented.
This is verified using the UART as well as the Arch LED
system. The GPIO interupt system is stubbed out but not
implemented.
* Arch LEDS -- The blue LED as part of the RGB LED is configured
and attached to the Arch LED system. This indicates the device
coming online as well as when a hardfault is triggered.
Applications and Testing:
* There is a nsh configuration implemented that includes debug
features as well as the ostest, getprime, and mem test.
All of these have been run and verified.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
so all boards support uClibc++/libc++ automatically
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ibe6fafbec57f7acb26ea6188a3e9923ea82295c5