After #6400 the prebuilt bootloader may be used for loading the NuttX
images when BUILD_PROTECTED is enabled.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Sync some of the AXI configuration and DDR training parameters with the manufacturer's
defaults.
The TIP_CFG parameter correction helps with DDR training failures on some individual boards
The AXI end address values fix early random crash in power-on boot on some individual boards
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Update PLL configuration parameters to match the values provided
by the vendor.
Also remove extra call to mpfs_pll_config() as it's already called
at mpfs_clockconfig().
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This provides USB composite (CDC/ACM and Mass Storage) support
for mpfs board. In addition, a number of USB fixes are included:
- Support for Setup Out packets
- Proper support for larger than packet size writes
- Finishing setup packets properly
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Linux kernel uses M-mode trap for handling Inter-Hart Communication (IHC).
This patch provides all the required functionalities for this purpose.
Previously, HSS bootloader was required. Now, NuttX is run as the
bootloader providing OpenSBI vendor extensions instead. This setup has
been tested on the following configuration:
- Hart 0 has NuttX in bootloader mode with OpenSBI
- Hart 1 unused
- Hart 2 has NuttX configured at 0xa2000000
- Hart 3 has U-boot / Linux kernel (at 0x80200000)
- Hart 4 has U-boot / Linux kernel (at 0x80200000)
Upon startup, NuttX on hart 0 will initialize SD-card driver, loads
the hart 2 NuttX from the SD-card and loads the U-boot to 0x80200000.
Also the nuttx.sbi -binary is loaded from SD-card into address 0x80000000,
which is also marked as reserved area in the Linux kernel device tree (for
the chuck 0x80000000 - 0x80200000).
Hart 2 NuttX waits until Linux kernel (IHC master) is started. After the
initial handshake, RPMsg / virtIO bus along with the IHC may be used for
proper AMP mode.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This provides an example of Asymmetric Multiprocessing (AMP). The
master from Linux sends pings that this NuttX echoes back. The system
uses RPMsg from OpenAMP.
The Inter-Hart Communication module is present in the vendor's software
stack with the tag "2021.11". The software is present on github at the
polarfire-soc project. The following conditions must be met:
1. FPGA programmed with 2021.11 software
2. HSS (Vendor bootloader) with 2021.11 software
3. U-boot and Linux kernel from 2011.11 software
Currently the IHC works as a slave only on the hart number 4.
On the NuttX side, this patch uses rptun that incorporates rpmsg and
virtio. If it used only rpmsg and virtio, the future maintenance would
likely be much heavier. Using rptun also simplifies many things.
Upon success, the master side from Linux may issue an example test:
root@icicle-kit-es-amp:/opt/microchip/amp/rpmsg-pingpong# ./rpmsg-pingpong
However, the rpmsg-pingpong.c (compiled on target with gcc), may need to
be modified as seen below to match the device id:
- char *rpmsg_dev="virtio0.rpmsg-amp-demo-channel.-1.0";
+ char *rpmsg_dev="virtio0.rpmsg-amp-demo-channel.-1.1024";
This work uses a separate linker script. Due to a bug yet unknown to date,
a small NuttX, when loaded by the vendor HSS bootloader, will cause the
Linux kernel to hang at boot. Thus, the binary size is increased with
a section 'filler_area' whose only purpose is to increase the image size
so that the Linux kernel will boot up.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Summary:
- This commit adds hostfs support to nsh and nsh64 defconfigs
Impact:
- None
Testing:
- Tested with qemu-6.2
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Mappings are done with vaddr=paddr.
- I/O space mapped with two gigapages
- Kernel space mapped to statically allocated page tables. 2MB of kernel
memory is supported.
- Page pool is mapped to the kernel space, to allow virtual memory access
for the kernel e.g. to initialize the page memory when it is allocated.
Selecting this option will pass "-Map=$(TOPDIR)$(DELIM)nuttx.map" to ld
when linking NuttX ELF. That file can be useful for verifying
and debugging magic section games, and for seeing which
pieces of code get eliminated with DEBUG_OPT_UNUSED_SECTIONS.
Signed-off-by: chao.an <anchao@xiaomi.com>
Enable this option to optimization the unused input sections with the
linker by compiling with " -ffunction-sections -fdata-sections ", and
linking with " --gc-sections ".
Signed-off-by: chao.an <anchao@xiaomi.com>
Follow: http://glennastory.net/boot/sysinit.html
This is first script that init runs is rc.sysinit. This
script does serval initialization tasks about basic service.
The boot sequence currently provided to the board level is:
board_earlyinitialize->
board_lateinitialize(Peripherals driver, core driver, ...)->
run rcS script(mount fs, run service) ->
board_appinitialize->
After this patch:
The boot sequence currently provided to the board level is:
board_earlyinitialize->
board_lateinitialize(core driver,...)->
run rc.sysinit script(mount fs, run core service) ->
board_appinitialize(Peripherals driver)->
run rcS script(run other service)->
So, Peripheral drivers can do more with the file system and
core services.
Signed-off-by: Jiuzhu Dong <dongjiuzhu1@xiaomi.com>
- Add config "ARCH_USE_S_MODE" which controls whether the kernel
runs in M-mode or S-mode
- Add more MSTATUS and most of the SSTATUS register definitions
- Add more MIP flags for interrupt delegation
- Add handling of interrupts from S-mode
- Add handling of FPU from S-mode
- Add new context handling functions that are not dependent on the trap
handlers / ecall
NOTE: S-mode requires a companion SW (SBI) which is not yet implemented,
thus S-mode is not usable as is, yet.
