This provides an example of Asymmetric Multiprocessing (AMP). The
master from Linux sends pings that this NuttX echoes back. The system
uses RPMsg from OpenAMP.
The Inter-Hart Communication module is present in the vendor's software
stack with the tag "2021.11". The software is present on github at the
polarfire-soc project. The following conditions must be met:
1. FPGA programmed with 2021.11 software
2. HSS (Vendor bootloader) with 2021.11 software
3. U-boot and Linux kernel from 2011.11 software
Currently the IHC works as a slave only on the hart number 4.
On the NuttX side, this patch uses rptun that incorporates rpmsg and
virtio. If it used only rpmsg and virtio, the future maintenance would
likely be much heavier. Using rptun also simplifies many things.
Upon success, the master side from Linux may issue an example test:
root@icicle-kit-es-amp:/opt/microchip/amp/rpmsg-pingpong# ./rpmsg-pingpong
However, the rpmsg-pingpong.c (compiled on target with gcc), may need to
be modified as seen below to match the device id:
- char *rpmsg_dev="virtio0.rpmsg-amp-demo-channel.-1.0";
+ char *rpmsg_dev="virtio0.rpmsg-amp-demo-channel.-1.1024";
This work uses a separate linker script. Due to a bug yet unknown to date,
a small NuttX, when loaded by the vendor HSS bootloader, will cause the
Linux kernel to hang at boot. Thus, the binary size is increased with
a section 'filler_area' whose only purpose is to increase the image size
so that the Linux kernel will boot up.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Summary:
- This commit adds hostfs support to nsh and nsh64 defconfigs
Impact:
- None
Testing:
- Tested with qemu-6.2
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Mappings are done with vaddr=paddr.
- I/O space mapped with two gigapages
- Kernel space mapped to statically allocated page tables. 2MB of kernel
memory is supported.
- Page pool is mapped to the kernel space, to allow virtual memory access
for the kernel e.g. to initialize the page memory when it is allocated.
Selecting this option will pass "-Map=$(TOPDIR)$(DELIM)nuttx.map" to ld
when linking NuttX ELF. That file can be useful for verifying
and debugging magic section games, and for seeing which
pieces of code get eliminated with DEBUG_OPT_UNUSED_SECTIONS.
Signed-off-by: chao.an <anchao@xiaomi.com>
Enable this option to optimization the unused input sections with the
linker by compiling with " -ffunction-sections -fdata-sections ", and
linking with " --gc-sections ".
Signed-off-by: chao.an <anchao@xiaomi.com>
Follow: http://glennastory.net/boot/sysinit.html
This is first script that init runs is rc.sysinit. This
script does serval initialization tasks about basic service.
The boot sequence currently provided to the board level is:
board_earlyinitialize->
board_lateinitialize(Peripherals driver, core driver, ...)->
run rcS script(mount fs, run service) ->
board_appinitialize->
After this patch:
The boot sequence currently provided to the board level is:
board_earlyinitialize->
board_lateinitialize(core driver,...)->
run rc.sysinit script(mount fs, run core service) ->
board_appinitialize(Peripherals driver)->
run rcS script(run other service)->
So, Peripheral drivers can do more with the file system and
core services.
Signed-off-by: Jiuzhu Dong <dongjiuzhu1@xiaomi.com>
- Add config "ARCH_USE_S_MODE" which controls whether the kernel
runs in M-mode or S-mode
- Add more MSTATUS and most of the SSTATUS register definitions
- Add more MIP flags for interrupt delegation
- Add handling of interrupts from S-mode
- Add handling of FPU from S-mode
- Add new context handling functions that are not dependent on the trap
handlers / ecall
NOTE: S-mode requires a companion SW (SBI) which is not yet implemented,
thus S-mode is not usable as is, yet.
RISC-V GCC is configured with --enable-initfini-array so it emits an
.init_array section instead of .ctors
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
## Summary
`esp32c3_spi2_cmddata()` implements SPI Cmd/Data `SPI_CMDDATA()` for only 3 LCD drivers: ST7735, ST7789 and GC9A01.
This patch removes the check for LCD drivers, so that SPI Cmd/Data will work for all LCD drivers.
More details: https://github.com/apache/incubator-nuttx/pull/5898
## Impact
This change impacts LCD drivers that call `SPI_CMDDATA()`.
Previously `SPI_CMDDATA()` would fail with `ENODEV` for LCD drivers other than ST7735, ST7789 and GC9A01.
After patching, `SPI_CMDDATA()` will work correctly with all LCD drivers.
## Testing
This is a minor patch so no testing is needed.
MCUboot apps were moved to examples directory. This fix configs due to
recent changes.
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
Move the target specific memory map to a separate file so there is no
need to copy&paste the __xxram_start etc linker symbols to each file
that needs them.
Also add MMU flags for I/O and kernel areas, they will be needed
when the kernel runs with virtual addresses also.
Mux USB IO pins one-by-one using package specific pinmux definitions. This avoids accidentally overwriting IO settings for other pins.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This adds a simple USB device driver for the mpfs. However,
this driver is still at its early phase. Only limited testing
with CDC/ACM has been conducted.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
