back at physical address 0x2007C000 and 0x20080000 (i.e. right below and right
above a 512 KiB boundary). Memory from those two blocks is considered
continuous when assigned to a heap.
In the protected build mode, when the memory protection unit is used, though,
it must be split into two MPU regions. This is because MPU regions must be
naturally aligned, and the 32KiB continuous address space of the two 16KiB AHB
SRAM blocks does not start at an address divisible by 32KiB.
The only other configurations that use protected build mode on lpc17xx are
currently open1788/knsh and open1788/knxterm. The LPC1788 has the AHB SRAM
blocks mapped more sanely (from an MPU region point of view), which is
probably why no problems emerged here. Both still compile with my change and
other than wasting an MPU region (which would otherwise remain unused) should
work fine. That said, I have no hardware to confirm.
tools: add flash_writter for cxd56 boards
this flash writter is using the xmodem for firmware transfer
for flashing please use
tools/flash_writer.py -s -c /dev/ttyUSB0 -d -b 115200 -n nuttx.spk
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch/arm/src/am335x: Add logic to map the framebuffer to a non-cached, non-buffered memory region.
arch/arm/src/am335x: Remove struct am335x_fbinfo_s. Replaced with configuration settings that provide the same information.
Squashed commit of the following:
arch/arm/src/am335x/am335x_lcdc.c: LCD driver now compiles.
arch/arm/src/am335x/am335x_lcd.c: This brings the LCD driver to code complete. Have not yet attempted to compile.
arch/arm/src/am335x/am335x_edid.c: Framebuffer is pre-allocated. In verification of video mode, include a test to assure that the video mode can be supported by the pre-allocated framebuffer memory.
arch/arm/src/am335x/am335x_lcd.c: At a little bit of LCD initialization logic. There is a long way to go.
arch/arm/src/am335x/am335x_edid.c: Add am335x_lcd_videomode() which provides an alternative way of initializing the LCD controller.
arch/arm/src/am335x/am335x_edid.c: edit.h has move to include/nuttx/video.
arch/arm/src/am335x/hardware/am335x_cm.h: Fix a typo in a macro name.
arch/arm/src/am335x/am335x_edid.c: Integrate video/edid support.
arch/arm/src/am335x/am335x_edid.c: Fall back to VGA mode is not valid videomode is availabe in the EDID data.
arch/arm/src/am335x/am335x_edid.c: Fixes for a partially clean compile.
arch/arm/src/am335x/am335x_edid.c: Add basic logic to convert EDID montor descriptions into a form usable for LCD configuration.
arch/arm/src/am335x: Add framework (only) for an LCD driver. Initial commit is simply the LPC54 framebuffer driver with naming changes.
Mastertools: add spk binary format and entry point for mpy
* tools: add spk binary format
The .spk binary format is used on spresense and other boards
based on the cxd56 arch.
to enable this binary format please set in your config
CONFIG_CXD56_BINARY=y
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: buils nuttx.spk images
Enable nuttx.spk binary image that can be flashed on spresense board.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: add entry point for mpy
The entry point is needed for the downstream projects based
on spresense.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
nucleo-144: Add reset feature
Code is aligned from
configs/stm32f4discovery/src/stm32_reset.c
It can be enabled using CONFIG_BOARDCTL_RESET
Change-Id: I296a628490abec102ef4bacb26b0356f970f226d
Signed-off-by: Philippe Coval <p.coval@samsung.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
drivers: video: add basic Video Stream support
basic video stream and capture implementation based on the
spresense SDK code release
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Improve gs2200m performance
* arch/arm/src/cxd56xx: Fix dma initialization in cxd56_dmac.c
up_dma_initialize() must be used instead of up_dmainitialize()
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* drivers/wireless: Introduce CONFIG_WL_GS2200M_SPI_FREQUENCY
Also, changed usleep(100) to up_udelay(100) to avoid invalid response.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* configs/spresense/wifi: Improve performance for webserver
This commit changes followings.
1. Enable SPI DMA for both TX and RX
2. Increase SPI clock speed from 4MHz to 10MHz
3. Increase buffer size for sendfile() from 512B to 1KB
4. Enable sendfile() for webserver
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch/arm/src/tiva: Add a workaround for tiva with qemu
With qemu, tiva_ifup() hangs because ethernet link status can not
be set correctly. This PR is a workaround to avoid this issue.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
