Summary:
- This commit updates README.txt regarding how to build kernel
and apps for BUILD_KERNEL
- Also update on parallel build for BUILD_FLAT
Impact:
- None
Testing:
- Tested with qemu-7.1.0
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- This commit adds ksmp64 configuration to test BUILD_KERNEL+SMP
- NOTE: README.txt has been updated
Impact:
- None
Testing:
- Tested with QEMU 6.2
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- I noticed that the OpenSBI library depends on the BSD license
- This commit fixes this issue
Impact:
- None
Testing:
- Build only
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Simplify the clock mode from the board.h -files. Also make the
SD clock definable as well.
Co-authored-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Some related products, such as Aries m100pfs, don't support eMMC
speeds up to 200MHz. Thus, provide option to select slower clock.
This has only to do with the clocking, no CMD6 is sent to select
high speed modes.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
The underlying hardware supports 9 endpoints:
- EP0
- 4x IN EPs
- 4x OUT EPs
Currently the driver assumes every EP number is unique. This limits
the amount of EPs to 1 + 4 = 5. Utilize the EPs in such a manner
that all may be used.
Also fix a few error handling related bugs. Update the composite
driver to match the current situation as well.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
rename the UDP_BINDTODEVICE to SO_BINDTODEVICE to follow the linux
style to be compatible with non-UDP protocol binding requirements
Signed-off-by: chao.an <anchao@xiaomi.com>
It is not really needed; g_hart_stacks is only used during SBI init as
a temporary stack area. We can use the scratch area buffers for this, as
the scratch areas define almost 4K of extra space, which is used for
exception stacks anyway.
After #6400 the prebuilt bootloader may be used for loading the NuttX
images when BUILD_PROTECTED is enabled.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Sync some of the AXI configuration and DDR training parameters with the manufacturer's
defaults.
The TIP_CFG parameter correction helps with DDR training failures on some individual boards
The AXI end address values fix early random crash in power-on boot on some individual boards
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Update PLL configuration parameters to match the values provided
by the vendor.
Also remove extra call to mpfs_pll_config() as it's already called
at mpfs_clockconfig().
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This provides USB composite (CDC/ACM and Mass Storage) support
for mpfs board. In addition, a number of USB fixes are included:
- Support for Setup Out packets
- Proper support for larger than packet size writes
- Finishing setup packets properly
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Linux kernel uses M-mode trap for handling Inter-Hart Communication (IHC).
This patch provides all the required functionalities for this purpose.
Previously, HSS bootloader was required. Now, NuttX is run as the
bootloader providing OpenSBI vendor extensions instead. This setup has
been tested on the following configuration:
- Hart 0 has NuttX in bootloader mode with OpenSBI
- Hart 1 unused
- Hart 2 has NuttX configured at 0xa2000000
- Hart 3 has U-boot / Linux kernel (at 0x80200000)
- Hart 4 has U-boot / Linux kernel (at 0x80200000)
Upon startup, NuttX on hart 0 will initialize SD-card driver, loads
the hart 2 NuttX from the SD-card and loads the U-boot to 0x80200000.
Also the nuttx.sbi -binary is loaded from SD-card into address 0x80000000,
which is also marked as reserved area in the Linux kernel device tree (for
the chuck 0x80000000 - 0x80200000).
Hart 2 NuttX waits until Linux kernel (IHC master) is started. After the
initial handshake, RPMsg / virtIO bus along with the IHC may be used for
proper AMP mode.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
