According to RFC 2525, Section 2.17:
"When an application closes a connection in such a way that it can no longer read any received data, the TCP SHOULD, per section 4.2.2.13 of RFC 1122, send a RST if there is any unread received data, or if any new data is received."
When our TCP socket is closed (even when the thread has exited), the peer can keep sending data and NuttX keeps replying ACK (we've tried for ~12h). This is not a good behavior (also different from Linux), so send RST instead of ACK for data receiving in FIN_WAIT.
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
Problem:
A SOCK_CTRL socket may be led to udp_pollsetup but never reaches
udp_pollteardown, it seems that we shouldn't call udp_pollsetup for
other socket types.
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
There might be some cases that we receive an event after socket is closed because of out-of-ordered rpmsg, since it may not cause problem, we may omit the error.
Also change log level to err when returning negated errno, because if we return negated errno, we'll directly trigger RPMSG_ASSERT outside, so we need at least an error message to indicate the reason.
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
SOCK_CTRL is added to provide special control over network drivers
and daemons. Currently, SOCK_DGRAM and SOCK_STREAM perform this control,
but these use socket resources. In the case of usersocket in particular,
this is a waste of the device's limited socket resources.
The priorities for finding a network adapter are as follows:
1. if laddr is not ANY, use laddr to find device;
2. if laddr is ANY, and bound index is not 0, use bound index
to find device;
3. if laddr is ANY and no device is bound, use raddr to find
device.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
SOCK_CTRL is added to provide special control over network drivers
and daemons. Currently, SOCK_DGRAM and SOCK_STREAM perform this control,
but these use socket resources. In the case of usersocket in particular,
this is a waste of the device's limited socket resources.
1.
net/slip.c:865:29: warning: unused variable ‘priv’ [-Wunused-variable]
865 | FAR struct slip_driver_s *priv =
| ^~~~
net/slip.c: In function ‘slip_rmmac’:
net/slip.c:895:29: warning: unused variable ‘priv’ [-Wunused-variable]
895 | FAR struct slip_driver_s *priv =
| ^~~~
2.
local/local_sendmsg.c: In function ‘local_sendmsg’:
local/local_sendmsg.c:423:18: warning: ‘count’ may be used uninitialized in this function [-Wmaybe-uninitialized]
423 | return count;
| ^~~~~
local/local_sendmsg.c:131:11: warning: ‘i’ may be used uninitialized in this function [-Wmaybe-uninitialized]
131 | while (i-- > 0)
| ~^~
local/local_sendmsg.c:71:7: note: ‘i’ was declared here
71 | int i;
| ^
Signed-off-by: chao an <anchao@xiaomi.com>
1.
ipfrag/ipv4_frag.c: In function ‘ipv4_fragin’:
ipfrag/ipv4_frag.c:184:22: warning: ‘head’ may be used uninitialized in this function [-Wmaybe-uninitialized]
184 | ipv4->len[1] = head->io_pktlen & 0xff;
| ~~~~^~~~~~~~~~~
ipfrag/ipv4_frag.c:123:21: note: ‘head’ was declared here
123 | FAR struct iob_s *head;
| ^~~~
2.
devif/ipv6_input.c: In function ‘ipv6_in’:
devif/ipv6_input.c:60:33: error: ‘TCPIPv6BUF’ undeclared (first use in this function); did you mean ‘UDPIPv6BUF’?
60 | #define PAYLOAD ((FAR uint8_t *)TCPIPv6BUF)
| ^~~~~~~~~~
3.
nat/ipv4_nat.c: In function ‘ipv4_nat_inbound_icmp’:
nat/ipv4_nat.c:67:30: error: ‘TCP_HDRLEN’ undeclared (first use in this function); did you mean ‘UDP_HDRLEN’?
67 | ((proto) == IP_PROTO_TCP ? TCP_HDRLEN : \
| ^~~~~~~~~~
nat/ipv4_nat.c:323:47: note: in expansion of macro ‘L4_HDRLEN’
323 | inner_l4hdrlen = MIN(inner_l4len, L4_HDRLEN(inner->proto));
| ^~~~~~~~~
Signed-off-by: chao an <anchao@xiaomi.com>
