So far the SD-card functionality has been tested with
the driver. Now, also the internal eMMC has been tested
working with this patch. This patch applies IOMUX and
clock settings that have been tested working with the
internal eMMC in the Polarfire Icicle kit.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This adds the proper flag for introducing the DDR
support. Also call the mpfs_ddr_init() at the
proper location.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This adds DDR training. The training has a small chance of failing,
and then the training is restarted.
DDR training cannot be done meaningfully while the software is
in DDR. If the system is intended to run from eNVM, like a
bootloader, the linker script should be tuned to utilize the envm
region as follows:
envm (rx) : ORIGIN = 0x20220100, LENGTH = 128K - 256
l2lim (rwx) : ORIGIN = 0x08000000, LENGTH = 1024k
256 bytes are reserved for the system; The fixed block may be
installed from the 'hart-software-services' -repository:
https://github.com/polarfire-soc/hart-software-services.git
For example, the 256-byte image: hss-envm-wrapper-bm1-dummySbic.bin
may be prepended on the nuttx bootloader image in the following
manner:
cat hss-envm-wrapper-bm1-dummySbic.bin > nuttx_bootloader.bin
cat nuttx.bin >> nuttx_bootloader.bin
riscv64-unknown-elf-objcopy -I binary -O ihex --change-section-lma
*+0x20220000 nuttx_bootloader.bin flashable_image.hex
This provides an image 'flashable_image.hex' that may be flashed on
the eNVM region via Microsemi Libero tool.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
- Fix the FPU enabling code
- If booting from eNVM, all harts start booting. With CONFIG_MPFS_BOOTLOADER,
one can allow just one hart booting and rest are stuck in wfi.
- Check that mtvec is actually updated before continuing the boot
- Create 5 IRQ stacks, one for each hart
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- Jump to mpfs_start with mhartid in a0 as the comment says
- Don't invalidate mmu tlb on e51 (it doesn't have mmu)
- Fix FPU initialization flags on e54 (it fires IRQ5 and crashes)
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Gregory Nutt has submitted the SGA
Florian Olbrich has submitted the ICLA
as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Almost all charger chip need the same oprations, which was not
appropriate only for BQ2429X. Therefore, open the operations to
all charger chips.
Signed-off-by: zhangguoliang <zhangguoliang3@xiaomi.com>
Since the tests were removed from the drivers, there is no need for
these defconfigs anymore.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
This commit adds header file imxrt_adc_etc.h for external ADC trigger
module. This contains only definitions of ADC_ETC registers and separate
bits, implementation of ADC_ETC driver is yet to be done.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
If we repeatedly call up_cpu_pause and up_cpu_resume, there would be
cases where the next call to up_cpu_pause happens while the other CPU is
still responding to the previous resume request. In this case the
DEBUGASSERT will trigger. We should allow the first CPU to wait until the
other CPU has finished responding to the resume request.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
