When the machine is cold started, the psram area where the syslog
buffer is located contains some random values, so it will cause
loss of valid log.
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
Add a function to read PolarFire's serial number from system controller, and use the first five digits as device's mac address
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Workaround to avoid deadlock situation: The RX shall not try to wait for complete
frame in case there is RX errors detected.
In case mpfs_receive is called, it keeps waiting for complete frame and
also keeps the net_lock locked. In the mean while, the TX may run out of free
descriptors, but can not get net_lock mutex lock to be able to release used
descriptors. If there are no free TX descs it disables RX interrupts because
it may require to send response to the received frame.
So, TX side keeps RX interrupts disabled due to lack of free descriptors and
RX blocks TX to release those descs by stubbornly waiting for complete frame.
When the system starts up, the hw count may not start counting from 0,
which can cause the processing time of the first oneshot handler to be
too long. Therefore, the current tick value should be set based on the
hw count during initialization.
Signed-off-by: zhangyuan21 <zhangyuan21@xiaomi.com>
RPMSG is associated with the use of HPWORK / LPWORK queues.
After sending a message to the remote end (Linux), the system
waits for an ack before proceeding. Unfortunately this may
take sometimes more time than one would expect. Ack waiting is
also unnecessary: nothing is done with that information. Even
worse, the net_lock() is also held during the blocked time so
it blocks other network stacks that are unrelated to this.
Also reorganize the mpfs_opensbi_*.S so that the trap
handler is easily relocated in the linker .ld file without
the need to relocate the utils.S. This makes it easier to
separate the files into own segments. The trap file should be
located in the zero device.
Moreover, provide support for simultaneous ACK and message
present handling capabilities in both directions. There are
times when both bits are set but only other is being handled.
In the end, the maximum throughput of the RPMSG bus increases
easily 10-20% or even more.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This commits adds support of UART2 for EPS32S3 and fixes pin mode
assignment for iomux mode
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
The class device only handles descriptor information specific to the class,
and shared descriptor information is passed through parameters and
handled by the composite driver.
Signed-off-by: zhangyuan21 <zhangyuan21@xiaomi.com>
Provide initial support for audio through the I2S peripheral to the
CS4344 audio codec on ESP32-S3-DevKitC-1 board.
Please check documentation for usage examples.
The master clock frequency should be multiple of the sample rate
and bit clock at the same time. Then, check if the current master
clock satisfies such a condition and set it accordingly otherwise.
In order to gracefully stop the I2S stream, add an interface to set
a `streaming` status variable that sets the `AUDIO_APB_FINAL` flag
that will be handled by the upper layers of the audio subsystem.
According to RX/TX operation, the DMA descriptors (inlink/outlink)
should be set differently. When setting the inlink, the `suc_eof`
field must be cleared by software (it will be set by hardware when
a packet is received). Similarly, the `length` field will be set
by hardware a packet is received.
Define macros used to access the registers of the GDMA channels
according to the selected channel in the header file, enabling them
to be used by other drivers.
By splitting into two different functions the setup of the DMA
descriptors and the action of loading it to the GDMA outlink
register, it enables us to "cache" DMA descriptors ready to be send
and, then, just load them whenever we are able to actually send it.
The macro `SET_BITS` only sets the bits according to the bit mask
and, once it's being used to set the address field of the GDMA
inlink/outlink register, it's necessary to clean all the bits
corresponding to that field that were eventually setup previously
to avoid messing with the bits that correspond to the current
address being setup.
Whevenever the bit rate is going to be set, it's necessary to first
set the master clock if the underlying device supports it. If it
fails, just return the error code.
According to the struct `mclk_rate_s`, set the default sample rate
to its lowest valid value. This prevents the underlying driver from
setting unsupported values.
Create bmi160_base.h, bmi160_base.c bmi160_uorb.c files, the bmi160_base file stores
public function interfaces, and the bmi160_uorb file stores functions related to the
uorb framework. Switch the character interface and UORB interface through the
macro CONFIG_SENSORS_BMI160_UORB.
Signed-off-by: likun17 <likun17@xiaomi.com>
This option enables architecture-specific memory copy for dynamic code loading.
For example, Ambiq has MRAM regions for instruction which can't load by
the memcpy directly.
Signed-off-by: wangjianyu3 <wangjianyu3@xiaomi.com>
Load all sections to LMA not VMA, so the startup code(e.g. start.S) need
relocate .data section to the final address(VMA) and zero .bss section by self.
For example, SiFli and Actions: Background: Device with small sram,
Bootloader run in sram and psram, need boot to Application, with memory overlap
and without XIP. VMA of .data is in "psram" and LMA in "rom", if not enable
`ELF_LOADTO_LMA`, ELF loader will load the section to VMA (will fill bootloader
itself).
Signed-off-by: wangjianyu3 <wangjianyu3@xiaomi.com>
