Basic work required for uniprocessor CortexR52 (ARMv8R AARCH32) using
GICv3 and CP15 mapped arch timer.
Tested on ARM FVP 11.20.
Port is based on ARMv8R AARCH64 and ARMv7R code. Excuse possible copy-paste leftovers.
When a task needs to send data, a callback is allocated and the
transmission is happening in a worker task through devif_send.
Synchronization between the two tasks (sender & worker) is
achieved by a semaphore.
If devif_send fails, this semaphore was never posted, leaving
the sending task blocked indefinitely. This commit fixes this
by checking the return code of netif_send, and posting this
semaphore in case of failure.
Polling then stops, and execution is resumed on the sending
task.
Summary:
- I noticed that the driver sends incorrect packets sometimes.
- This commit fixes this issue.
Impact:
- None
Testing:
- Tested with qemu-7.1
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Remove unnecessary reading of the status register when loading / unloading
the FIFOs. Reading from the IP block is slow due to BUS synchronization and
this basically makes the SPI busy loop for no reason at all, destroying the
CPU usage.
The overall benefit of these changes is approx. 25%-points, which is a
MASSIVE improvement.
Adds a driver for an FPGA fabric / CoreSPI implementation.
Supports multiple instances, assuming they reside in some base address,
offsettable by a constant value.
Add an interface that validate if EasyDMA transfer is possible.
EasyDMA cannot access flash memory which can cause hard to detect silent bugs.
This feature is enabled if CONFIG_DEBUG_FEATURES=y and CONFIG_DEBUG_ASSERTIONS=y.
External function to query vbus status. Reading from the block requires
the clock, but if no devices are open -> vbus detect does not work.
This creates a chicken / egg problem, if vbus detect is used to start
the usb device.
warning: (NET_SOLINGER) selects NET_UDP_NOTIFIER which has unmet direct dependencies
(NET && NET_UDP && !NET_UDP_NO_STACK && SCHED_WORKQUEUE)
Signed-off-by: chao an <anchao@xiaomi.com>
bmp388 works poorly as the system fires STOPs even in
a beginning of a transaction. Don't let unrelated STOPs
to distort the data flow.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This adds 2 more FPGA I2Cs. Also rework the indexing
so that it matches the earlier work without major changes.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This fixes the following issue:
- After sending the address, the driver writes an extra zero
Without this patch, the extra write causes an extra ACK that would
terminate the sequence prematurely. This is observed as data read
corruption.
With this fix, the condition is detected precisely. That being the
case, the sequence is continued with a repeated start, after which
the read continues normally.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This incorporates an fpga i2c driver into the existing i2c driver.
This fpga i2c works almost 100% as the MSS i2c, but the difference
is that the fpga driver terminates all transactions with a stop
sent -interrupt. That needs to be handled.
Fpga clock source is also different, act accordingly.
SEC2TICK(10) is an overkill to any app, use just one second instead.
modifyreg32s are simplified as well, no need to clear and set
as set is enough.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
I2C status register reset value (0xf8) was not handled properly causing unnecessary bus resets.
Added critical section to mpfs_i2c_reset() and removed unnecessary interrupt disabling elsewhere.
Problem:
When tcp_close_work starts to run in LPWORK, if another event comes and
calls tcp_free before tcp_close_work takes net_lock, the tcp_free will
be called twice and cause double free.
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
Board related code may use different mounts for MTD device (block
character for one, SmartFS for another) if required by the board.
Additional type member was therefore added to mtd_partition_s structure
in order to support this.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
