Adds a driver for an FPGA fabric / CoreSPI implementation.
Supports multiple instances, assuming they reside in some base address,
offsettable by a constant value.
Currently the IHC (Inter Hart Communication) depends on OpenAMP and
rptun. However, the bootloader portion of the IHC doesn't need
either of them. Now they are wasting a lot of bootloader space.
Reorganize the bootloader portion into a separate file 'mpfs_ihc_sbi.c'.
This file contains the OpenSBI vendor extensions, or the only required
functionalities for the bootloader. On the other hand, 'mpfs_ihc.c'
contains the non-bootloader code.
This patch also makes it possible to utilize 2 RPMSG channels. This
has been tested so that 2 separate NuttXs on harts 1 and 2 communicate
with Linux kernel that runs on harts 3 and 4.
New configuration files are added as well:
- rpmsg-ch1: sample config for RPMSG
- rpmsg-ch2: sample config for another RPMSG channel
- rpmsg-sbi: sample bootloader config for RPMSG/OpenSBI
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
The underlying hardware supports 9 endpoints:
- EP0
- 4x IN EPs
- 4x OUT EPs
Currently the driver assumes every EP number is unique. This limits
the amount of EPs to 1 + 4 = 5. Utilize the EPs in such a manner
that all may be used.
Also fix a few error handling related bugs. Update the composite
driver to match the current situation as well.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This provides USB composite (CDC/ACM and Mass Storage) support
for mpfs board. In addition, a number of USB fixes are included:
- Support for Setup Out packets
- Proper support for larger than packet size writes
- Finishing setup packets properly
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Linux kernel uses M-mode trap for handling Inter-Hart Communication (IHC).
This patch provides all the required functionalities for this purpose.
Previously, HSS bootloader was required. Now, NuttX is run as the
bootloader providing OpenSBI vendor extensions instead. This setup has
been tested on the following configuration:
- Hart 0 has NuttX in bootloader mode with OpenSBI
- Hart 1 unused
- Hart 2 has NuttX configured at 0xa2000000
- Hart 3 has U-boot / Linux kernel (at 0x80200000)
- Hart 4 has U-boot / Linux kernel (at 0x80200000)
Upon startup, NuttX on hart 0 will initialize SD-card driver, loads
the hart 2 NuttX from the SD-card and loads the U-boot to 0x80200000.
Also the nuttx.sbi -binary is loaded from SD-card into address 0x80000000,
which is also marked as reserved area in the Linux kernel device tree (for
the chuck 0x80000000 - 0x80200000).
Hart 2 NuttX waits until Linux kernel (IHC master) is started. After the
initial handshake, RPMsg / virtIO bus along with the IHC may be used for
proper AMP mode.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This provides an example of Asymmetric Multiprocessing (AMP). The
master from Linux sends pings that this NuttX echoes back. The system
uses RPMsg from OpenAMP.
The Inter-Hart Communication module is present in the vendor's software
stack with the tag "2021.11". The software is present on github at the
polarfire-soc project. The following conditions must be met:
1. FPGA programmed with 2021.11 software
2. HSS (Vendor bootloader) with 2021.11 software
3. U-boot and Linux kernel from 2011.11 software
Currently the IHC works as a slave only on the hart number 4.
On the NuttX side, this patch uses rptun that incorporates rpmsg and
virtio. If it used only rpmsg and virtio, the future maintenance would
likely be much heavier. Using rptun also simplifies many things.
Upon success, the master side from Linux may issue an example test:
root@icicle-kit-es-amp:/opt/microchip/amp/rpmsg-pingpong# ./rpmsg-pingpong
However, the rpmsg-pingpong.c (compiled on target with gcc), may need to
be modified as seen below to match the device id:
- char *rpmsg_dev="virtio0.rpmsg-amp-demo-channel.-1.0";
+ char *rpmsg_dev="virtio0.rpmsg-amp-demo-channel.-1.1024";
This work uses a separate linker script. Due to a bug yet unknown to date,
a small NuttX, when loaded by the vendor HSS bootloader, will cause the
Linux kernel to hang at boot. Thus, the binary size is increased with
a section 'filler_area' whose only purpose is to increase the image size
so that the Linux kernel will boot up.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
- Add config "ARCH_USE_S_MODE" which controls whether the kernel
runs in M-mode or S-mode
- Add more MSTATUS and most of the SSTATUS register definitions
- Add more MIP flags for interrupt delegation
- Add handling of interrupts from S-mode
- Add handling of FPU from S-mode
- Add new context handling functions that are not dependent on the trap
handlers / ecall
NOTE: S-mode requires a companion SW (SBI) which is not yet implemented,
thus S-mode is not usable as is, yet.
This adds a simple USB device driver for the mpfs. However,
this driver is still at its early phase. Only limited testing
with CDC/ACM has been conducted.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
The image must be placed into:
boards/risc-v/mpfs/icicle/include/boot_romfsimg.h
The image is mounted by mpfs_bringup, which is run by the application
itself, or by board_late_initialize() in the case when
CONFIG_BOARD_LATE_INITIALIZE is defined, e.g. with CONFIG_BUILD_KERNEL
- Add defconfig and board specific files
- Create mpfs/common for code which is shared between MPFS boards.
- Add support for GPIO driven EMMCSD mux.
- Move DDR Libero definitions from arch to boards.
Signed-off-by: Jani Paalijarvi <jani.paalijarvi@unikie.com>
