Fixes for MFRC522
drivers/contactless/mfrc522.c: in mfrc522_read uid.sak must be different from 0x04 not as before from 0x00. SAK == 0x00 is a valid PICC type
drivers/contactless/mfrc522.c: add interface to read MIFARE Ultralight data
configs/nucleo-l073rz: add mfrc522 support
Approved-by: Gregory Nutt <gnutt@nuttx.org>
SX127X improvements
drivers/wireless/lpwan/sx127x/sx127x: add TX power configuration
drivers/wireless/lpwan/sx127x/sx127x: discard RX packets with unsupported length
drivers/wireless/lpwan/sx127x/sx127x: refactor some logic
drivers/wireless/lpwan/Kconfig: move some hardcoded sx127x configuration to Kconfig
drivers/wireless/lpwan/Kconfig: remove EXPERIMENTAL flag
configs/b-l072z-lrwan1/sx127x: board-specific sx127x configuration
configs/nucleo-f091rc/sx127x: board-specific sx127x configuration
configs/nucleo-l073rz/sx127x: board-specific sx127x configuration
LORA and FSK look fine but there is something missing for OOK and communication is not working yet.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
sched/init/nx_start.c: Add support for CONFIG_BOARD_DRIVER_INITIALIZE. If this option is selected then nx_start() will call a board-provided function board_driver_initialize() immediately after calling up_initialize().
Rename CONFIG_BOARD_INITIALIZE to CONFIG_BOARD_LATE_INITIALIZE.
Raname board_initialize() to board_late_initialize()
Master
arch/arm/src/stm32f0l0: SPI support for F0
arch/arm/src/stm32f0l0/Kconfig: L0 parts should select STM32F0L0_STM32L0
arch/arm/src/stm32f0l0/hardware: unify names for ADC/DAC/DMA/CAN
drivers/wireless/lpwan/sx127x/sx127x.c: return immediately when ISR0 is called but sx127x is not initialized
configs/nucleo-f091rc: support for sx127x
configs/nucleo-l073rz: cosmetics
configs/b-l072z-lrwan1/include/board.h: use HSI as default clock source and fix typo in SPI1 pins
Approved-by: GregoryN <gnutt@nuttx.org>
stm32f0l0: SPI and GPIO EXTI support
arch/arm/src/stm32f0l0: add support for GPIO EXTI
configs/nucleo-l073rz: support for nrf24l01
configs/b-l072z-lrwan1/include/board.h: add note about onboard Murata CMWX1ZZABZ-09 module and definitions for available peripherals
Approved-by: GregoryN <gnutt@nuttx.org>
Squashed commit of the following:
arch/arm/src/stm32f0l0: Various changes for a clean compilation. Still does not compile correctly due to missing FLASH latency definitions.
arch/arm/src/stm32f0l0/hardware: Add framework for the STM32 L0. Currently set to same as the STM32F0.
arch/arm/src/stm32f0l0/hardware: Very fragmentary FLASH header register definitions for the STM32 L0.
arch/arm/src/stm32f0l0: Bring in DMA v1. Cannot possibly be functionaly yet due to the limited number for M0 interrupts.
arch/arm/src/stm32f0l0: Add STM32 F0/L0 LSE and backup power domain controls.
arch/arm/src/stm32f0l0/hardware/stm32l0_pwr.h: Add STM32L0 PWR header file.
arch/arm/include/stm32f0l0/chip.h: Clean up WIP chip header file.
arch/arm/include/stm32f0l0/chip.h: WIP.
arm/src/stm32f0l0: Resolve some small differences between F0 and L0 GPIO pin options.
arch/arm/src/stm32f0l0: Better integrate STM32L0 header files.
nuttx/arch/arm/include/stm32f0l0: Add STM32L0 IRQ number definition file.
arch/arm/src/stm32f0l0: Add STM32L0 RCC driver.
arch/arm/src/stm32f0l0/hardware: Adds basic STM32L0 header files.
arch/arm/src/stm32f0l0: Add STM32L0 chip selections.
configs/: Hook new STM32L0 boards into the configuration system.
configs: nucleo boards use as default ST LINK MCO as clock input from MCU and for this HSEBYP must be enabled
configs: add basic support for nucleo-l073rz
configs: add basic support for b-l072z-lrwan1
