1. Adjust code to avoid PM wakelock->count less than or equal to 0.
2. Fix some document format issues.
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
Since SSTC is support by QEMU 7.2.9, kernel mode nuttx is no
longer worked for older QEMU.
Add necessary requirement information for rv-virt board.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
The qemu-rv use a small init code for M mode in kernel build.
It is hard-coding and is difficult to change. Due to the fact,
introduce a already mature SBI implement (e.g OpenSBI) to
replace existing code is a better choice.
This patch introduce some change for qemu-rv:
1. use SSTC to provide time interrupt in kernel build
2. remove uncessary M mode trap.
For simplicity, this patch does not add support for booting
nuttx for any core, but force boot core to start core 0 and
let core 0 do the initialization.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
1. pm configuration demonstrates the use of power management present on the ESP32-S3.
2. You can use the pmconfig command to test the power management, for details look at
``Documentation/platforms/xtensa/esp32s3/boards/esp32s3-devkit/index.rst``
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
It is advisable to set bootdelay to 0 when using bootcmd to disable
dcache on u-boot. Using bootdelay -1 will definitely work as it disables
bootcmd altogether (and leaves the dcache enabled). This step is added
to remove confusion.
Notes:
1. This version of NAT66 is a stateful one like NAT44, corresponding to Linux's MASQUERADE target of ip6tables. We can support stateless NAT66 & NPTv6 later by slightly modify the address & port selection logic (maybe just match the rules and skip the entry find).
2. We're using same flag `IFF_NAT` for both NAT44 & NAT66 to make control easier. Which means, if we enable NAT, both NAT44 & NAT66 will be enabled. If we don't want one of them, we can just disable that one in Kconfig.
3. Maybe we can accelerate the checksum adjustment by pre-calculate a difference of checksum, and apply it to each packet, instead of calling `net_chksum_adjust` each time. Just a thought, maybe do it later.
4. IP fragment segments on NAT66 connections are not supported yet.
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
To prepare for future IPv6 NAT functions.
- Rename common ipv4_nat_xxx to nat_xxx
- Move some common definitions into header
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
The symmetric NAT limits one external port to be used with only one peer ip:port.
Note:
1. To avoid using too much #ifdef, we're always passing peer_ip and peer_port as arguments, but won't use them under full cone NAT, let the compiler optimize them.
2. We need to find port binding without peer ip:port, so don't add peer ip:port into hash key.
3. Symmetric NAT needs to *select another external port if a port is used by any other NAT entry*, this behavior is exactly same as Full Cone NAT, so we don't need to change anything related to `ipv4_nat_port_inuse`.
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
Adds board definition for imx93-evk board
- Support for the Cortex-A55 core in i.MX93, support for the Cortex-M33
core is _not_ provided
- "nsh" profile is provided, this includes a minimalistic feature set
which boots the SoM to nsh console
- A bootloader is required, u-boot has been tested
This driver is used with QEMU, to make it possible
to use networking.
This is not the MAC in ESP32, however, it can be used with QEMU.
The code was shamelessly copied from 31dac92e5f
This commit adds support for TX DMA transfers for USART peripheral. Code
refactor in sam_serial.h was also required in order to have correct
defines for all possible cases (both RX and TX DMA used, just one used,
none used).
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
