Most tools used for compliance and SBOM generation use SPDX identifiers
This change brings us a step closer to an easy SBOM generation.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
In this change, if board/include and board/script are not found, they will be looked for again in the upper level of common.
Signed-off-by: chenrun1 <chenrun1@xiaomi.com>
This patch modify the script to update only the boards configs
of an specific chip or only the boards of an specific architecture.
Examples:
refresh.sh add custom board verify
custom board:
$ ./tools/refresh.sh --silent ../../xxx/configs/ap
$ ./tools/refresh.sh --silent /yyy/xxx/configs/ap
$ ./tools/refresh.sh --silent yyy/xxx/configs/ap
Signed-off-by: dengwenqi <dengwenqi@xiaomi.com>
Currently when we modify some Kconfig related to some chip or
some architecture we need to run refresh.sh to all boards that
is too slow (more than one hour to finish).
This patch modify the script to update only the boards configs
of an specific chip or only the boards of an specific architecture.
Examples:
$ ./tools/refresh.sh --silent --defaults arch:renesas
Normalize us7032evb1/ostest
Normalize us7032evb1/nsh
Normalize skp16c26/ostest
Normalize rx65n-rsk2mb/netnsh
Normalize rx65n-rsk2mb/ipv6
Normalize rx65n-rsk2mb/nsh
Normalize rx65n-rsk1mb/netnsh
Normalize rx65n-rsk1mb/nsh
Normalize rx65n-grrose/netnsh
Normalize rx65n-grrose/ipv6
Normalize rx65n-grrose/nsh
Normalize rx65n/nsh
It updates the boards from all 'renesas' architecture (m9c, rx65n, sh1)
$ ./tools/refresh.sh --silent --defaults chip:rx65n
Normalize rx65n-rsk2mb/netnsh
Normalize rx65n-rsk2mb/ipv6
Normalize rx65n-rsk2mb/nsh
Normalize rx65n-rsk1mb/netnsh
Normalize rx65n-rsk1mb/nsh
Normalize rx65n-grrose/netnsh
Normalize rx65n-grrose/ipv6
Normalize rx65n-grrose/nsh
Normalize rx65n/nsh
It updates all the boards from renesas chip 'rx65n' family
There is case as below:
When do testbuild under Linux host, such as './tools/configure.sh stmf4discovery:nsh',
arch/arm/src/board is a symlink to boards/arm/stm32/stm32f3discovery/src. Then do
'./tools/refresh.sh --silent stmf4discovery:nsh' after build, it would break the board
symlink with copydir.sh instead of link.sh since defconfig with Windows host config.
So call sethost.sh to restore BOARD_DIR. Or it results in 'make distclean' not correctly.
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
Author: Gregory Nutt <gnutt@nuttx.org>
Run all .c and .h modified in PR through nxstyle.
Author: Masayuki Ishikawa <masayuki.ishikawa@gmail.com>
feature k210 (#16)
* arch: risc-v: Add support for __LP64__ to types.h
* arch: risc-v: Add support for RV64GC to common files
* arch: risc-v: Add support for Kendryte K210 processor (RV64GC)
* boards: risk-v: Add support for Sipeed Maix Bit with K210
* tools: Add support for Kendryte K210 processor
1. Serial (UART) driver (13 ports)
2. Ethernet driver
This port is provided on two boards
1. RSK RX65N-2MB
2. GR-Rose
The port is built on Cygwin environment.
As part of this port, we have created two documents
1. Readme.txt for each board
2. User manual to provide information about development environment setup
Both these documents are placed under
1. /boards/renesas/rx65n/rx65n-grrose
2. /boards/renesas/rx65n/rx65n-rsk2mb
We have run 'nxstyle' for coding guidelines and 'ostest' for testing NuttX features on test platform.
We have shared the log with no errors as confirmation of valid port.
The legacy '/' delimiter is still supported but not recommend and not advertised.
Squashed commit of the following:
Update configurations instructions in more README.txt files to show ':' delimiter vs '/' delimiter.
Update configurations instructions in various README.txt file to show ':' delimiter vs '/' delimiter.
tools: Update all configuration-related tools to accept ':' separator between board and configuration name.
Move boards to boards folder
* boards: rename configs folder to boards
This is the proposed layout after the change:
boards: - folder containing board folders
<board>: - name of each board
drivers: - extra drivers specific for platform
include: - header files for the boars
scripts: - extra scripts specific for platform
src: - board specific code
tools: - extra tools specific for platform
<config>: - board specific configuration(s)
Note:
<xxx> names are dependent on platform
This is a logical change to aim to the arch layout but this is a
huge change it should be done in several steps to lower the risk.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Kconfig: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile.*: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Make.defs: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .sh: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .mk: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .c & .h: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .bat: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
