As long as the GNSS feature is not used, GNSS RAM can be used as general memory.
This memory is 640KByte total, which is lower performance than the application RAM.
It is possible to locate text, data and bss into GNSS RAM and to use as heap area.
SAMA5D2 has UART (TX/RX only) and FLEXCOM USART (with control pins).
UART has only TX/RX, so if I try to use flow control with FLEXCOM USART,
there is no register definition on the UART side and get a compilation error.
Signed-off-by: Takeyoshi Kikuchi <kikuchi@centurysys.co.jp>
Commit 03e5c02 introduced option to have both standard SPI and QSPI
in SPI mode on one system. However this change broke the appearance of
QSPI driver configuration menu entry in menuconfig as it was dependent
on !SAMV7_QSPI_IS_SPI (which is now true for all MCUs having standard
SPI ability in QSPI driver).
This change makes sure the menu is correctly shown when QSPI driver
used.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit refactors DAC driver. The functionality remains the same
but driver start up is now done in dac_setup (after application called
open function) instead of sam_dac_initialize (called from BSP). This
ensures that driver does not take resources (timer, interrupt) until
opened. Implementation of dac_shutdown is also provided, therefore
the driver frees resources once closed.
This change is consistent with other drivers implementation.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
USART peripheral can work in SPI mode as well. This commit adds support
for such functionality. Only 1 slave device is supported by the
peripheral therefore board level does not have to ensure correct CS
setup.
The usage of the peripheral is the same as with other SPI drivers.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
If a TX DMA completion interrups a forground write.
The TX DMA completion can start a dma_send and it will
then followed by the forground write's dma_send
stoping the,then in progress DMA.
By atomicaly marking the tx dma busy, the forground
write will not perform the dma_send, and will only
enqueue the data. At the next TX dma completion any
data pending in the tx queue will be sent
The logic of the conditional expression that determines whether
the QH is a target QH or not is reversed in the process of canceling
a transfer in INPROGRESS state.
Therefore, the QH in INPROGRESS state is not released and subsequent
communication is not successful.
Checked with CDC-ACM driver and cu command.
Signed-off-by: Takeyoshi Kikuchi <kikuchi@centurysys.co.jp>
Newly added logging in `sched/task_exit.c` obsoletes the existing
ones in `arch/up_exit()`, thus remove the latter to reduce duplications.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
armv8-r/arm_gicv3.c: In function 'gic_validate_dist_version':
armv8-r/arm_gicv3.c:730:9: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'uint32_t' {aka 'long unsigned int'} [-Wformat=]
730 | sinfo("GICD_TYPER = 0x%x\n", typer);
| ^~~~~~~~~~~~~~~~~~~~~ ~~~~~
| |
| uint32_t {aka long unsigned int}
armv8-r/arm_gicv3.c:730:26: note: format string is defined here
730 | sinfo("GICD_TYPER = 0x%x\n", typer);
| ~^
| |
| unsigned int
| %lx
Signed-off-by: chao an <anchao@lixiang.com>
Add ARCH_CHIP_QEMU_TRUSTZONE to enable/disable the TrustZone
support beacause qemu also support enable/disable Arm Security
Extensions: https://qemu-project.gitlab.io/qemu/system/arm/virt.html
when launch.
Signed-off-by: Bowen Wang <wangbowen6@xiaomi.com>
since gcc report the false alarm if the pointer offset from zero address:
inlined from 'up_vectormapping' at chip/dm320_boot.c:162:7,
inlined from 'arm_boot' at chip/dm320_boot.c:211:3:
Error: chip/dm320_boot.c:117:17: error: array subscript 0 is outside array bounds of 'uint32_t[0]' {aka 'long unsigned int[]'} [-Werror=array-bounds=]
117 | ctable[index] = (paddr | mmuflags);
| ~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
The `xxx_ipv6multicast` function in each driver is not adapted to
multiple IPv6 addresses yet, and they're redundant, so try to take them
into common code.
Change:
1. Add MAC `g_ipv6_ethallnodes` and `g_ipv6_ethallrouters` in
`icmpv6_devinit` and call them in `netdev_register`
2. Add multicast MAC for Neighbor Solicitation when adding any IPv6
address, and remove them when IPv6 address is removed
3. Select `NET_MCASTGROUP` when `NET_ICMPv6` because now we need
`d_addmac` when we have ICMPv6
Note:
We want modules outside net stack to call functions like
`netdev_ipv6_add` and never touch the related MAC address, so these MAC
functions are added as internal functions to `net/netdev/netdev.h`
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
