Gregory Nutt
|
2ad6e4452b
|
Add new framework for the PCM decoder. It is now a 'front end' for lower-level drivers like the WM8904 that performs the PCM decoding from end
|
2014-07-22 11:54:13 -06:00 |
|
Gregory Nutt
|
54986c41d8
|
SAMA5 PCK: Add support for the slow clock as the PCK clock source
|
2014-07-19 13:55:08 -06:00 |
|
Gregory Nutt
|
f240f7e513
|
SAMA5: Add slow clock support
|
2014-07-19 13:07:55 -06:00 |
|
Gregory Nutt
|
414fb2b154
|
SAMA5D4-EK: Add WM8904 initialization logic
|
2014-07-19 11:58:53 -06:00 |
|
Gregory Nutt
|
17fdc797ed
|
WM8904: A few initial definitions for for the SAMA5D4-EK
|
2014-07-17 17:57:57 -06:00 |
|
Gregory Nutt
|
a86fb3a38c
|
SAMA5D4-EK: Valid MXT interrupts should only occur on the falling edge of the ~CHG signal
|
2014-07-12 14:03:08 -06:00 |
|
Gregory Nutt
|
32f22b6611
|
SAMA5D44-EK: Cosmetic changes
|
2014-07-09 07:18:43 -06:00 |
|
Gregory Nutt
|
ad9b0653f5
|
Some cosmetic typo fixes
|
2014-07-09 07:12:16 -06:00 |
|
Gregory Nutt
|
19d8b0ce97
|
Fix some cloned errors in SAM GPIO interrupt setup
|
2014-07-07 15:54:37 -06:00 |
|
Gregory Nutt
|
6cb13fde4e
|
maXTouch: Fix some issues with interrupt handling
|
2014-07-07 13:25:20 -06:00 |
|
Gregory Nutt
|
0d4dcdd079
|
maXTouch: Fix I2C address, errors when debug enable, reorganize some data
|
2014-07-06 08:03:34 -06:00 |
|
Gregory Nutt
|
6fab16e6f9
|
MXT interface does not need an IRQ number; SAMA5D4-EK setup omitted I2C frequency
|
2014-07-05 17:47:17 -06:00 |
|
Gregory Nutt
|
ea330b030e
|
Clean-up some comments
|
2014-07-05 17:15:38 -06:00 |
|
Gregory Nutt
|
5e98d5d2e8
|
SAMA5D4-EK: Add board support for the maXTouch
|
2014-07-05 17:12:14 -06:00 |
|
Gregory Nutt
|
73ed49fe06
|
SAMA5D4-EK: Add support for USB host
|
2014-07-03 11:22:15 -06:00 |
|
Gregory Nutt
|
4478d1ba72
|
SAMA5 HSMCI: Dump GPIO configuration if DEBUG enabled
|
2014-06-29 17:47:25 -06:00 |
|
Gregory Nutt
|
88953d95f7
|
SAMA5D4-EK: Fix HSMCI card-detect pin selections
|
2014-06-29 11:26:41 -06:00 |
|
Gregory Nutt
|
5cffe94448
|
Minor update to AT25BOOT; Updated README file
|
2014-06-28 12:38:41 -06:00 |
|
Gregory Nutt
|
fc5a45ddd1
|
SAMA5D4-EK: Fix some AT25BOOT bugs
|
2014-06-28 11:15:02 -06:00 |
|
Gregory Nutt
|
84b74bcf7c
|
SAMA5D4-EK: Updates to get the at25boot configuration building correctly
|
2014-06-28 09:39:50 -06:00 |
|
Gregory Nutt
|
80fd710ce7
|
SAMA5D4-EK: Add a configuration to load a boot program into AT25 FLASH
|
2014-06-28 08:40:11 -06:00 |
|
Gregory Nutt
|
2bc3217f84
|
SAMA5D4: Bootloader needs to flush D-Cache to memory before disabling the caches
|
2014-06-27 14:09:02 -06:00 |
|
Gregory Nutt
|
001278a93a
|
Cosmetic update to comments
|
2014-06-27 11:55:33 -06:00 |
|
Gregory Nutt
|
2be17d64b3
|
SAMA5D4-EK: Add bootloader that runs from ISRAM and loads an Intel HEX file into DRAM
|
2014-06-26 16:42:06 -06:00 |
|
Gregory Nutt
|
02591c509b
|
SAMA5D4-EK: Make sure that the H32MX divider is set; correct sense of bit driver red LED
|
2014-06-20 10:33:33 -06:00 |
|
Gregory Nutt
|
66b0a121f1
|
SAMA5D4: Implement SDRAM initialization
|
2014-06-14 10:42:26 -06:00 |
|
Gregory Nutt
|
b4607cc444
|
SAMA5D4: Add support for HSMCI1 power control pin
|
2014-06-11 14:55:51 -06:00 |
|
Gregory Nutt
|
57da49beb3
|
SAMA5D4-EK: Update pins used by HSMCI
|
2014-06-11 14:45:01 -06:00 |
|
Gregory Nutt
|
1634a11bd0
|
SAMA5D3/4: More renaming. Change SAMA5D3 EMAC to EMACA and SAMA5D4 to EMACB so that the configuration and build system can configure them. I might come up with something better later
|
2014-06-10 17:40:25 -06:00 |
|
Gregory Nutt
|
895851314f
|
Updated SAMA5 SFR header file for the SAMA5D4
|
2014-06-08 07:48:36 -06:00 |
|
Gregory Nutt
|
24af2deb30
|
Update SAMA5D4-EK PIO usage
|
2014-06-07 09:37:17 -06:00 |
|
Gregory Nutt
|
e8f8d3f521
|
Add board support for the SAMA5D4-EK
|
2014-06-06 12:37:36 -06:00 |
|