sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
0040dcf858
nuttx/boards/arm/stm32/nucleo-f429zi/src/nucleo-144.h
Xiang Xiao 7990f90915 Indent the define statement by two spaces 
follow the code style convention

Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
2023-05-21 09:52:08 -03:00

270 lines
9.0 KiB
C
Raw Blame History

/****************************************************************************
* boards/arm/stm32/nucleo-f429zi/src/nucleo-144.h
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
#ifndef __BOARDS_ARM_STM32F4_NUCLEO_F429ZI_SRC_NUCLEO_144_H
#define __BOARDS_ARM_STM32F4_NUCLEO_F429ZI_SRC_NUCLEO_144_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <stdint.h>
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* Configuration ************************************************************/
/* procfs File System */
#ifdef CONFIG_FS_PROCFS
# ifdef CONFIG_NSH_PROC_MOUNTPOINT
# define STM32_PROCFS_MOUNTPOINT CONFIG_NSH_PROC_MOUNTPOINT
# else
# define STM32_PROCFS_MOUNTPOINT "/proc"
# endif
#endif
/* Nucleo-144 GPIO Pin Definitions ******************************************/
/* LED
*
* The Nucleo-144 board has numerous LEDs but only three, LD1 a Green LED,
* LD2 a Blue LED and LD3 a Red LED, that can be controlled by software.
* The following definitions assume the default Solder Bridges are installed.
*/
#define GPIO_LD1 (GPIO_OUTPUT | GPIO_PUSHPULL | GPIO_SPEED_50MHz | GPIO_OUTPUT_CLEAR | \
GPIO_PORTB | GPIO_PIN0)
#define GPIO_LD2 (GPIO_OUTPUT | GPIO_PUSHPULL | GPIO_SPEED_50MHz | GPIO_OUTPUT_CLEAR | \
GPIO_PORTB | GPIO_PIN7)
#define GPIO_LD3 (GPIO_OUTPUT | GPIO_PUSHPULL | GPIO_SPEED_50MHz | GPIO_OUTPUT_CLEAR | \
GPIO_PORTB | GPIO_PIN14)
#define GPIO_LED_GREEN GPIO_LD1
#define GPIO_LED_BLUE GPIO_LD2
#define GPIO_LED_RED GPIO_LD3
#define LED_DRIVER_PATH "/dev/userleds"
/* BUTTONS
*
* The Blue pushbutton B1, labeled "User", is connected to GPIO PC13.
* A high value will be sensed when the button is depressed.
* Note:
* 1) That the EXTI is included in the definition to enable
* an interrupt on this IO.
* 2) The following definitions assume the default Solder
* Bridges are installed.
*/
#define GPIO_BTN_USER (GPIO_INPUT | GPIO_FLOAT | GPIO_EXTI | GPIO_PORTC | GPIO_PIN13)
/* SPI **********************************************************************/
#define GPIO_SPI_CS (GPIO_OUTPUT | GPIO_PUSHPULL | GPIO_SPEED_50MHz | \
GPIO_OUTPUT_SET)
#define GPIO_SPI1_CS0 (GPIO_SPI_CS | GPIO_PORTA | GPIO_PIN15)
#define GPIO_SPI1_CS1 (GPIO_SPI_CS | GPIO_PORTC | GPIO_PIN15)
#define GPIO_SPI1_CS2 (GPIO_SPI_CS | GPIO_PORTC | GPIO_PIN14)
#define GPIO_SPI1_CS3 (GPIO_SPI_CS | GPIO_PORTC | GPIO_PIN2)
#define GPIO_SPI2_CS0 (GPIO_SPI_CS | GPIO_PORTD | GPIO_PIN7)
#define GPIO_SPI2_CS1 (GPIO_SPI_CS | GPIO_PORTG | GPIO_PIN1)
#define GPIO_SPI2_CS2 (GPIO_SPI_CS | GPIO_PORTG | GPIO_PIN2)
#define GPIO_SPI2_CS3 (GPIO_SPI_CS | GPIO_PORTG | GPIO_PIN3)
#define GPIO_SPI3_CS0 (GPIO_SPI_CS | GPIO_PORTG | GPIO_PIN4)
#define GPIO_SPI3_CS1 (GPIO_SPI_CS | GPIO_PORTG | GPIO_PIN5)
#define GPIO_SPI3_CS2 (GPIO_SPI_CS | GPIO_PORTG | GPIO_PIN6)
#define GPIO_SPI3_CS3 (GPIO_SPI_CS | GPIO_PORTG | GPIO_PIN7)
#if defined(CONFIG_STM32_SDMMC1) || defined(CONFIG_STM32_SDMMC2)
# define HAVE_SDIO
#endif
#if defined(CONFIG_DISABLE_MOUNTPOINT) || !defined(CONFIG_MMCSD_SDIO)
# undef HAVE_SDIO
#endif
#define SDIO_SLOTNO 0 /* Only one slot */
#ifdef HAVE_SDIO
# if defined(CONFIG_STM32_SDMMC1)
# define GPIO_SDMMC1_NCD (GPIO_INPUT|GPIO_FLOAT|GPIO_EXTI | GPIO_PORTC | GPIO_PIN6)
# endif
# if defined(CONFIG_NSH_MMCSDSLOTNO) && (CONFIG_NSH_MMCSDSLOTNO != 0)
# warning "Only one MMC/SD slot, slot 0"
# define CONFIG_NSH_MMCSDSLOTNO SDIO_SLOTNO
# endif
# if defined(CONFIG_NSH_MMCSDMINOR)
# define SDIO_MINOR CONFIG_NSH_MMCSDMINOR
# else
# define SDIO_MINOR 0
# endif
#endif
/* USB OTG FS
*
* PA9 OTG_FS_VBUS VBUS sensing (also connected to the green LED)
* PC0 OTG_FS_PowerSwitchOn
* PD5 OTG_FS_Overcurrent
*/
#define GPIO_OTGFS_VBUS (GPIO_INPUT|GPIO_FLOAT|GPIO_SPEED_100MHz|\
GPIO_OPENDRAIN|GPIO_PORTA|GPIO_PIN9)
#define GPIO_OTGFS_PWRON (GPIO_OUTPUT|GPIO_FLOAT|GPIO_SPEED_100MHz|\
GPIO_PUSHPULL|GPIO_PORTG|GPIO_PIN6)
#ifdef CONFIG_USBHOST
# define GPIO_OTGFS_OVER (GPIO_INPUT|GPIO_EXTI|GPIO_FLOAT|\
GPIO_SPEED_100MHz|GPIO_PUSHPULL|\
GPIO_PORTG|GPIO_PIN7)
#else
# define GPIO_OTGFS_OVER (GPIO_INPUT|GPIO_FLOAT|GPIO_SPEED_100MHz|\
GPIO_PUSHPULL|GPIO_PORTG|GPIO_PIN7)
#endif
/* GPIO pins used by the GPIO Subsystem */
#define BOARD_NGPIOIN 1 /* Amount of GPIO Input pins */
#define BOARD_NGPIOOUT 1 /* Amount of GPIO Output pins */
#define BOARD_NGPIOINT 1 /* Amount of GPIO Input w/ Interruption pins */
#define GPIO_IN1 (GPIO_INPUT | GPIO_FLOAT | GPIO_PORTB | GPIO_PIN0)
#define GPIO_OUT1 (GPIO_OUTPUT | GPIO_OUTPUT | GPIO_SPEED_50MHz | \
GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN1)
#define GPIO_INT1 (GPIO_INPUT | GPIO_FLOAT | GPIO_PORTB | GPIO_PIN2)
/****************************************************************************
* Public Data
****************************************************************************/
#ifndef __ASSEMBLY__
/****************************************************************************
* Name: stm32_spidev_initialize
*
* Description:
* Called to configure SPI chip select GPIO pins for the Nucleo-144 board.
*
****************************************************************************/
#if defined(CONFIG_SPI)
void stm32_spidev_initialize(void);
#endif
/****************************************************************************
* Name: stm32_spidev_bus_test
*
* Description:
* Called to create the defined SPI buses and test them by initializing
* them and sending the NUCLEO_SPI_TEST (no chip select).
*
****************************************************************************/
#if defined(CONFIG_NUCLEO_SPI_TEST)
int stm32_spidev_bus_test(void);
#endif
/****************************************************************************
* Name: stm32_dma_alloc_init
*
* Description:
* Called to create a FAT DMA allocator
*
* Returned Value:
* 0 on success or -ENOMEM
*
****************************************************************************/
void stm32_dma_alloc_init(void);
#if defined (CONFIG_FAT_DMAMEMORY)
int stm32_dma_alloc_init(void);
#endif
/****************************************************************************
* Name: stm32_sdio_initialize
*
* Description:
* Called at application startup time to initialize the SCMMC
* functionality.
*
****************************************************************************/
#ifdef CONFIG_MMCSD
int stm32_sdio_initialize(void);
#endif
/****************************************************************************
* Name: stm32_usbinitialize
*
* Description:
* Called from stm32_usbinitialize very early in inialization to
* setup USB-related GPIO pins for the nucleo-144 board.
*
****************************************************************************/
#ifdef CONFIG_STM32_OTGFS
void stm32_usbinitialize(void);
#endif
/****************************************************************************
* Name: stm32_pwm_setup
*
* Description:
* Initialize PWM and register the PWM device.
*
****************************************************************************/
#ifdef CONFIG_PWM
int stm32_pwm_setup(void);
#endif
/****************************************************************************
* Name: stm32_adc_setup
*
* Description:
* Initialize ADC and register the ADC driver.
*
****************************************************************************/
#ifdef CONFIG_ADC
int stm32_adc_setup(void);
#endif
/****************************************************************************
* Name: stm32_bbsram_int
****************************************************************************/
#ifdef CONFIG_STM32_BBSRAM
int stm32_bbsram_int(void);
#endif
#endif /* __ASSEMBLY__ */
#endif /* __BOARDS_ARM_STM32F4_NUCLEO_F429ZI_SRC_NUCLEO_144_H */
Reference in New Issue View Git Blame Copy Permalink