README
======
This directory holds the port to the NXP S32K146EVB-Q144 development board.
Contents
========
o Status
o Serial Console
o LEDs and Buttons
o OpenSDA Notes
o Thread-Aware Debugging with Eclipse
o Configurations
Status
======
2019-08-18: Configuration created but entirely untested.
2019-08-20: For initial testing, I ran out of SRAM to avoid the
brickage problems I had with the S32K118EVB (i.e., with
CONFIG_BOOT_RUNFROMISRAM=y). In this mode, the NSH configuration
appears to work correctly.
2019-08-21: Writing a relocated version of that same functional binary
into FLASH, however, did not work and, in fact, bricked my S32K146EVB.
That is because the first version of the FLASH image that I used
clobbered the FLASH Configuration bytes at address 0x0400 (I
didn't even know about these!). I have since modified the linker script
to skip this address in FLASH. There is some fragmentary discussion
for recovery from this condition at the NXP Community Forums, but none of
those options are working for me:
https://community.nxp.com/thread/505593
Given the success running from SRAM and the success of the same fixes
on the S32K118, I believe that the NSH configuration should now run out
of FLASH. Unfortunately, I cannot demonstrate that.
2019-10-19: The NXP Mobile Robotics team has demonstrated that the basic
NSH configuration runs out of FLASH without issues. The aforementioned
fixes for the FLASH issues were converted into a set of FLASH
configuration options, with a proven default state.
2019-11-07: A s32k146.cfg configuration file (for OpenOCD) was added to
the scripts/ folder.
2020-06-15: Added FlexCAN driver with SocketCAN support to the S32K1XX
arch. Should work also on the S32K146EVB board, but remains untested.
2020-06-16: Added Emulated EEPROM driver and initialization.
TODO: Need to calibrate the delay loop. The current value of
CONFIG_BOARD_LOOPSPERMSEC is a bogus value retained from a copy-paste
(see apps/examples/calib_udelay).
Serial Console
==============
By default, the serial console will be provided on the OpenSDA VCOM port:
OpenSDA UART RX PTC6 (LPUART1_RX)
OpenSDA UART TX PTC7 (LPUART1_TX)
USB drivers for the PEmicro CDC Serial Port are available here:
http://www.pemicro.com/opensda/
LEDs and Buttons
================
LEDs
----
The S32K146EVB has one RGB LED:
RedLED PTD15 (FTM0 CH0)
GreenLED PTD16 (FTM0 CH1)
BlueLED PTD0 (FTM0 CH2)
An output of '1' illuminates the LED.
If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in
any way. The following definitions are used to access individual RGB
components (see s32k146evb.h):
GPIO_LED_R
GPIO_LED_G
GPIO_LED_B
The RGB components could, alternatively, be controlled through PWM using
the common RGB LED driver.
If CONFIG_ARCH_LEDs is defined, then NuttX will control the LEDs on board
the S32K146EVB. The following definitions describe how NuttX controls the
LEDs:
==========================================+========+========+=========
RED GREEN BLUE
==========================================+========+========+=========
LED_STARTED NuttX has been started OFF OFF OFF
LED_HEAPALLOCATE Heap has been allocated OFF OFF ON
LED_IRQSENABLED Interrupts enabled OFF OFF ON
LED_STACKCREATED Idle stack created OFF ON OFF
LED_INIRQ In an interrupt (no change)
LED_SIGNAL In a signal handler (no change)
LED_ASSERTION An assertion failed (no change)
LED_PANIC The system has crashed FLASH OFF OFF
LED_IDLE S32K146 in sleep mode (no change)
==========================================+========+========+=========
Buttons
-------
The S32K146EVB supports two buttons:
SW2 PTC12
SW3 PTC13
OpenSDA Notes
=============
- USB drivers for the PEmicro CDC Serial Port are available here:
http://www.pemicro.com/opensda/
- The drag'n'drog interface expects files in .srec format.
- Using Segger J-Link: Easy... but remember to use the SWD connector J14
in the center of the board and not the OpenSDA connector closer to the
OpenSDA USB connector J7.
Thread-Aware Debugging with Eclipse
===================================
Thread-aware debugging is possible with openocd-nuttx
( https://github.com/sony/openocd-nuttx ) and was tested together with the
Eclipse-based S32 Design Studio for Arm:
https://www.nxp.com/design/software/development-software/s32-design-studio-ide/s32-design-studio-for-arm:S32DS-ARM
NOTE: This method was last tested with NuttX 8.2 and S32DS for Arm 2018.R1.
It may not work anymore with recent releases of NuttX and/or S32DS.
1. NuttX should be build with debug symbols enabled.
2. Build OpenOCD as described here (using the same parameters as well):
https://micro.ros.org/docs/tutorials/old/debugging/
3. A s32k146.cfg file is available in the scripts/ folder. Start OpenOCD
with the following command (adapt the path info):
/usr/local/bin/openocd -f /usr/share/openocd/scripts/interface/jlink.cfg \
-f boards/s32k1xx/s32k146evb/scripts/s32k146.cfg -c init -c "reset halt"
4. Setup a GDB debug session in Eclipse. The resulting debug window shows
the NuttX threads. The full stack details can be viewed.
Configurations
==============
Common Information
------------------
Each S32K146EVB configuration is maintained in a sub-directory and can be
selected as follows:
tools/configure.sh s32k146evb:<subdir>
Where <subdir> is one of the sub-directories listed in the next paragraph.
NOTES (common for all configurations):
1. This configuration uses the mconf-based configuration tool. To change
this configuration using that tool, you should:
a. Build and install the kconfig-mconf tool. See nuttx/README.txt.
Also see additional README.txt files in the NuttX tools repository.
b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.
2. Unless otherwise stated, the serial console used is LPUART1 at
115,200 8N1. This corresponds to the OpenSDA VCOM port.
Configuration Sub-directories
-----------------------------
nsh:
---
Configures the NuttShell (nsh) located at apps/examples/nsh. Support
for builtin applications is enabled, but in the base configuration the
only application selected is the "Hello, World!" example.
8defb843aa