883 lines
29 KiB
ReStructuredText
883 lines
29 KiB
ReStructuredText
=================
|
|
stm32f103-minimum
|
|
=================
|
|
|
|
This page discusses issues unique to NuttX configurations for the
|
|
STM32F103C8T6 Minimum System Development Board for ARM Microcontroller.
|
|
|
|
STM32F103C8T6 Minimum System Development Boards:
|
|
================================================
|
|
|
|
This STM32F103C8T6 minimum system development board is available from
|
|
several vendors on the net, and may be sold under different names or
|
|
no name at all. It is based on a STM32F103C8T6 and has a DIP-40 form-
|
|
factor.
|
|
|
|
There are four versions of very similar boards: Red, Blue, RoboDyn Black and
|
|
Black.
|
|
See: https://wiki.stm32duino.com/index.php?title=Blue_Pill
|
|
https://wiki.stm32duino.com/index.php?title=Red_Pill
|
|
https://wiki.stm32duino.com/index.php?title=RobotDyn_Black_Pill
|
|
https://wiki.stm32duino.com/index.php?title=Black_Pill
|
|
|
|
The Red Board:
|
|
|
|
Good things about the red board:
|
|
|
|
- 1.5k pull up resistor on the PA12 pin (USB D+) which you can
|
|
programmatically drag down for automated USB reset.
|
|
- large power capacitors and LDO power.
|
|
- User LED on PC13
|
|
|
|
Problems with the red board:
|
|
|
|
- Silk screen is barely readable, the text is chopped off on some of
|
|
the pins
|
|
- USB connector only has two anchor points and it is directly soldered
|
|
on the surface
|
|
- Small reset button with hardly any resistance
|
|
|
|
The Blue Board:
|
|
|
|
Good things about the blue board:
|
|
|
|
- Four soldered anchor point on the USB connector. What you can't tell
|
|
from this picture is that there is a notch in the PCB board and the USB
|
|
connector sits down inside it some. This provides some lateral stability
|
|
that takes some of the stress off the solder points.
|
|
- It has nice clear readable silkscreen printing.
|
|
- It also a larger reset button.
|
|
- User LED on PC13
|
|
|
|
Problems with the blue board:
|
|
|
|
- Probably won't work as a USB device if it has a 10k pull-up on PA12. You
|
|
have to check the pull up on PA12 (USB D+). If it has a 10k pull-up
|
|
resistor, you will need to replace it with a 1.5k one to use the native
|
|
USB.
|
|
- Puny voltage regulator probably 100mA.
|
|
|
|
A schematic for the blue board is available here:
|
|
http://www.stm32duino.com/download/file.php?id=276
|
|
|
|
The Black Board:
|
|
|
|
- User LED is on PB12.
|
|
- Mounting holes.
|
|
|
|
Both Boards:
|
|
|
|
Nice features common to both:
|
|
|
|
- SWD pins broken out and easily connected (VCC, GND, SWDIO, SWCLK)
|
|
- USB 5V is broken out with easy access.
|
|
- Power LED
|
|
- You can probably use more flash (128k) than officially documented for
|
|
the chip (stm32f103c8t6 64k), I was able to load 115k of flash on mine
|
|
and it seemed to work.
|
|
|
|
Problems with both boards:
|
|
|
|
- No preloaded bootloader (this isn't really a problem as the
|
|
entire 64k of flash is available for use)
|
|
- No user button
|
|
|
|
This is the board pinout based on its form-factor for the Blue board:
|
|
|
|
..
|
|
USB
|
|
___
|
|
-----/ _ \-----
|
|
|B12 GND|
|
|
|B13 GND|
|
|
|B14 3.3V|
|
|
|B15 RST|
|
|
|A8 B11|
|
|
|A9 B10|
|
|
|A10 B1|
|
|
|A11 B0|
|
|
|A12 A7|
|
|
|A15 A6|
|
|
|B3 A5|
|
|
|B4 A4|
|
|
|B5 A3|
|
|
|B6 A2|
|
|
|B7 A1|
|
|
|B8 A0|
|
|
|B9 C15|
|
|
|5V C14|
|
|
|GND C13|
|
|
|3.3V VB|
|
|
|_____________|
|
|
|
|
LEDs
|
|
====
|
|
|
|
The STM32F103 Minimum board has only one software controllable LED.
|
|
This LED can be used by the board port when CONFIG_ARCH_LEDS option is
|
|
enabled.
|
|
|
|
If enabled the LED is simply turned on when the board boots
|
|
successfully, and is blinking on panic / assertion failed.
|
|
|
|
UARTs
|
|
=====
|
|
|
|
UART/USART PINS
|
|
---------------
|
|
|
|
..
|
|
USART1
|
|
RX PA10
|
|
TX PA9
|
|
USART2
|
|
CK PA4
|
|
CTS PA0
|
|
RTS PA1
|
|
RX PA3
|
|
TX PA2
|
|
USART3
|
|
CK PB12
|
|
CTS PB13
|
|
RTS PB14
|
|
RX PB11
|
|
TX PB10
|
|
|
|
Default USART/UART Configuration
|
|
--------------------------------
|
|
|
|
USART1 (RX & TX only) is available through pins PA9 (TX) and PA10 (RX).
|
|
|
|
Timer Inputs/Outputs
|
|
====================
|
|
|
|
..
|
|
TIM1
|
|
CH1 PA8
|
|
CH2 PA9*
|
|
CH3 PA10*
|
|
CH4 PA11*
|
|
TIM2
|
|
CH1 PA0*, PA15, PA5
|
|
CH2 PA1, PB3
|
|
CH3 PA2, PB10*
|
|
CH4 PA3, PB11
|
|
TIM3
|
|
CH1 PA6, PB4
|
|
CH2 PA7, PB5*
|
|
CH3 PB0
|
|
CH4 PB1*
|
|
TIM4
|
|
CH1 PB6*
|
|
CH2 PB7
|
|
CH3 PB8
|
|
CH4 PB9*
|
|
|
|
* Indicates pins that have other on-board functions and should be used only
|
|
with care (See board datasheet).
|
|
|
|
Using 128KiB of Flash instead of 64KiB
|
|
======================================
|
|
|
|
Some people figured out that the STM32F103C8T6 has 128KiB of internal memory
|
|
instead of 64KiB as documented in the datasheet and reported by its internal
|
|
register.
|
|
|
|
In order to enable 128KiB you need modify the linker script to reflect this
|
|
new size. Open the boards/arm/stm32/stm32f103-minimum/scripts/ld.script and replace::
|
|
|
|
flash (rx) : ORIGIN = 0x08000000, LENGTH = 64K
|
|
|
|
with::
|
|
|
|
flash (rx) : ORIGIN = 0x08000000, LENGTH = 128K
|
|
|
|
Enable many NuttX features (ie. many filesystems and applications) to get a
|
|
large binary image with more than 64K.
|
|
|
|
We will use OpenOCD to write the firmware in the STM32F103C8T6 Flash. Use a
|
|
up to dated OpenOCD version (ie. openocd-0.9).
|
|
|
|
You will need to create a copy of original openocd/scripts/target/stm32f1x.cfg
|
|
to openocd/scripts/target/stm32f103c8t6.cfg and edit the later file replacing::
|
|
|
|
flash bank $_FLASHNAME stm32f1x 0x08000000 0 0 0 $_TARGETNAME
|
|
|
|
with::
|
|
|
|
flash bank $_FLASHNAME stm32f1x 0x08000000 0x20000 0 0 $_TARGETNAME
|
|
|
|
We will use OpenOCD with STLink-V2 programmer, but it will work with other
|
|
programmers (JLink, Versaloon, or some based on FTDI FT232, etc).
|
|
|
|
Open a terminal and execute::
|
|
|
|
$ sudo openocd -f interface/stlink-v2.cfg -f target/stm32f103c8t6.cfg
|
|
|
|
Now in other terminal execute::
|
|
|
|
$ telnet localhost 4444
|
|
|
|
Trying 127.0.0.1...
|
|
Connected to localhost.
|
|
Escape character is '^]'.
|
|
Open On-Chip Debugger
|
|
|
|
> reset halt
|
|
stm32f1x.cpu: target state: halted
|
|
target halted due to debug-request, current mode: Thread
|
|
xPSR: 0x01000000 pc: 0x080003ac msp: 0x20000d78
|
|
|
|
> flash write_image erase nuttx.bin 0x08000000
|
|
auto erase enabled
|
|
device id = 0x20036410
|
|
ignoring flash probed value, using configured bank size
|
|
flash size = 128kbytes
|
|
stm32f1x.cpu: target state: halted
|
|
target halted due to breakpoint, current mode: Thread
|
|
xPSR: 0x61000000 pc: 0x2000003a msp: 0x20000d78
|
|
wrote 92160 bytes from file nuttx.bin in 4.942194s (18.211 KiB/s)
|
|
|
|
> reset run
|
|
> exit
|
|
|
|
Now NuttX should start normally.
|
|
|
|
Nintendo Wii Nunchuck:
|
|
======================
|
|
|
|
There is a driver on NuttX to support Nintendo Wii Nunchuck Joystick. If you
|
|
want to use it please select these options:
|
|
|
|
- Enable the I2C1 at System Type -> STM32 Peripheral Support, it will enable:
|
|
|
|
CONFIG_STM32_I2C1=y
|
|
|
|
- Enable to Custom board/driver initialization at RTOS Features -> RTOS hooks
|
|
|
|
CONFIG_BOARD_LATE_INITIALIZE=y
|
|
|
|
- Enable the I2C Driver Support at Device Drivers, it will enable this symbol:
|
|
|
|
CONFIG_I2C=y
|
|
|
|
- Nintendo Wii Nunchuck Joystick at Device Drivers -> [*] Input Device Support
|
|
|
|
CONFIG_INPUT=y
|
|
CONFIG_INPUT_NUNCHUCK=y
|
|
|
|
- Enable the Nunchuck joystick example at Application Configuration -> Examples
|
|
|
|
CONFIG_EXAMPLES_NUNCHUCK=y
|
|
CONFIG_EXAMPLES_NUNCHUCK_DEVNAME="/dev/nunchuck0"
|
|
|
|
You need to connect GND and +3.3V pins from Nunchuck connector to GND and 3.3V
|
|
of stm32f103-minimum respectively (Nunchuck also can work connected to 5V, but
|
|
I don't recommend it). Connect I2C Clock from Nunchuck to SCK (PB6) and the
|
|
I2C Data to SDA (PB7).
|
|
|
|
Quadrature Encoder:
|
|
===================
|
|
|
|
The nsh configuration has been used to test the Quadrature Encoder
|
|
(QEncoder, QE) with the following modifications to the configuration
|
|
file:
|
|
|
|
- These setting enable support for the common QEncode upper half driver:
|
|
|
|
CONFIG_SENSORS=y
|
|
CONFIG_SENSORS_QENCODER=y
|
|
|
|
- This is a board setting that selected timer 4 for use with the
|
|
quadrature encode:
|
|
|
|
CONFIG_STM32F103MINIMUM_QETIMER=4
|
|
|
|
- These settings enable the STM32 Quadrature encoder on timer 4:
|
|
|
|
CONFIG_STM32_TIM4_CAP=y
|
|
CONFIG_STM32_TIM4_QE=y
|
|
CONFIG_STM32_TIM4_QECLKOUT=2800000
|
|
CONFIG_STM32_QENCODER_FILTER=y
|
|
CONFIG_STM32_QENCODER_SAMPLE_EVENT_6=y
|
|
CONFIG_STM32_QENCODER_SAMPLE_FDTS_4=y
|
|
|
|
- These settings enable the test case at apps/examples/qencoder:
|
|
|
|
CONFIG_EXAMPLES_QENCODER=y
|
|
CONFIG_EXAMPLES_QENCODER_DELAY=100
|
|
CONFIG_EXAMPLES_QENCODER_DEVPATH="/dev/qe0"
|
|
|
|
In this configuration, the QEncoder inputs will be on the TIM4 inputs of
|
|
PB6 and PB7.
|
|
|
|
SPI NOR Flash support:
|
|
======================
|
|
|
|
We can use an extern SPI NOR Flash with STM32F103-Minimum board. In this case
|
|
we tested the Winboard W25Q32FV (32Mbit = 4MiB).
|
|
|
|
You can connect the W25Q32FV module in the STM32F103 Minimum board this way:
|
|
connect PA5 (SPI1 CLK) to CLK; PA7 (SPI1 MOSI) to DI; PA6 (SPI MISO) to DO;
|
|
PA4 to /CS; Also connect 3.3V to VCC and GND to GND.
|
|
|
|
You can start with default "stm32f103-minimum/nsh" configuration option and
|
|
enable/disable these options using "make menuconfig" ::
|
|
|
|
System Type --->
|
|
STM32 Peripheral Support --->
|
|
[*] SPI1
|
|
|
|
Board Selection --->
|
|
[*] MTD driver for external 4Mbyte W25Q32FV FLASH on SPI1
|
|
(0) Minor number for the FLASH /dev/smart entry
|
|
[*] Enable partition support on FLASH
|
|
(1024,1024,1024,1024) Flash partition size list
|
|
|
|
RTOS Features --->
|
|
Stack and heap information --->
|
|
(512) Idle thread stack size
|
|
(1024) Main thread stack size
|
|
(256) Minimum pthread stack size
|
|
(1024) Default pthread stack size
|
|
|
|
Device Drivers --->
|
|
-*- Memory Technology Device (MTD) Support --->
|
|
[*] Support MTD partitions
|
|
-*- SPI-based W25 FLASH
|
|
(0) W25 SPI Mode
|
|
(20000000) W25 SPI Frequency
|
|
|
|
File Systems --->
|
|
[ ] Disable pseudo-filesystem operations
|
|
-*- SMART file system
|
|
(0xff) FLASH erased state
|
|
(16) Maximum file name length
|
|
|
|
Memory Management --->
|
|
[*] Small memory model
|
|
|
|
Also change the boards/arm/stm32/stm32f103-minimum/scripts/ld.script file to use 128KB
|
|
of Flash instead 64KB (since this board has a hidden 64KB flash) :
|
|
|
|
MEMORY
|
|
{
|
|
flash (rx) : ORIGIN = 0x08000000, LENGTH = 128K
|
|
sram (rwx) : ORIGIN = 0x20000000, LENGTH = 20K
|
|
}
|
|
|
|
Then after compiling and flashing the file nuttx.bin you can format and mount
|
|
the flash this way:
|
|
|
|
nsh> mksmartfs /dev/smart0p0
|
|
nsh> mksmartfs /dev/smart0p1
|
|
nsh> mksmartfs /dev/smart0p2
|
|
nsh> mksmartfs /dev/smart0p3
|
|
|
|
nsh> mount -t smartfs /dev/smart0p0 /mnt
|
|
nsh> ls /mnt
|
|
/mnt:
|
|
|
|
nsh> echo "Testing" > /mnt/file.txt
|
|
|
|
nsh> ls /mnt
|
|
/mnt:
|
|
file.txt
|
|
|
|
nsh> cat /mnt/file.txt
|
|
Testing
|
|
|
|
nsh>
|
|
|
|
SDCard support:
|
|
===============
|
|
|
|
Only STM32F103xx High-density devices has SDIO controller. STM32F103C8T6 is a
|
|
Medium-density device, but we can use SDCard over SPI.
|
|
|
|
You can do that enabling these options::
|
|
|
|
CONFIG_FS_FAT=y
|
|
|
|
CONFIG_MMCSD=y
|
|
CONFIG_MMCSD_NSLOTS=1
|
|
CONFIG_MMCSD_SPI=y
|
|
CONFIG_MMCSD_SPICLOCK=20000000
|
|
CONFIG_MMCSD_SPIMODE=0
|
|
|
|
CONFIG_STM32_SPI=y
|
|
CONFIG_STM32_SPI1=y
|
|
|
|
CONFIG_SPI=y
|
|
CONFIG_SPI_CALLBACK=y
|
|
CONFIG_SPI_EXCHANGE=y
|
|
|
|
And connect a SDCard/SPI board on SPI1. Connect the CS pin to PA4, SCK to
|
|
PA5, MOSI to PA7 and MISO to PA6. Note: some chinese boards use MOSO instead
|
|
of MISO.
|
|
|
|
Nokia 5110 LCD Display support:
|
|
===============================
|
|
|
|
You can connect a low cost Nokia 5110 LCD display in the STM32F103 Minimum
|
|
board this way: connect PA5 (SPI1 CLK) to CLK; PA7 (SPI1 MOSI) to DIN; PA4
|
|
to CE; PA3 to RST; PA2 to DC. Also connect 3.3V to VCC and GND to GND.
|
|
|
|
You can start with default "stm32f103-minimum/nsh" configuration option and
|
|
enable these options using "make menuconfig" ::
|
|
|
|
System Type --->
|
|
STM32 Peripheral Support --->
|
|
[*] SPI1
|
|
|
|
Device Drivers --->
|
|
-*- SPI Driver Support --->
|
|
[*] SPI exchange
|
|
[*] SPI CMD/DATA
|
|
|
|
Device Drivers --->
|
|
LCD Driver Support --->
|
|
[*] Graphic LCD Driver Support --->
|
|
[*] Nokia 5110 LCD Display (Phillips PCD8544)
|
|
(1) Number of PCD8544 Devices
|
|
(84) PCD8544 X Resolution
|
|
(48) PCD8544 Y Resolution
|
|
|
|
Graphics Support --->
|
|
[*] NX Graphics
|
|
(1) Number of Color Planes
|
|
|
|
(0x0) Initial background color
|
|
Supported Pixel Depths --->
|
|
[ ] Disable 1 BPP
|
|
[*] Packed MS First
|
|
|
|
Font Selections --->
|
|
(7) Bits in Character Set
|
|
[*] Mono 5x8
|
|
|
|
Application Configuration --->
|
|
Examples --->
|
|
[*] NX graphics "Hello, World!" example
|
|
(1) Bits-Per-Pixel
|
|
|
|
After compiling and flashing the nuttx.bin inside the board, reset it.
|
|
You should see it:
|
|
|
|
NuttShell (NSH)
|
|
nsh> ?
|
|
help usage: help [-v] [<cmd>]
|
|
|
|
[ dd free mb source usleep
|
|
? echo help mh sleep xd
|
|
cat exec hexdump mw test
|
|
cd exit kill pwd true
|
|
cp false ls set unset
|
|
|
|
Builtin Apps:
|
|
nxhello
|
|
|
|
Now just run nxhello and you should see "Hello World" in the display:
|
|
|
|
nsh> nxhello
|
|
|
|
HYT271 sensor support
|
|
=====================
|
|
|
|
The existing sensor configuration allows connecting several sensors of type
|
|
hyt271 on i2c bus number 2. For full feature support, be able to change the
|
|
i2c address of the sensor, the following hardware setup is necessary.::
|
|
|
|
---------- -----------
|
|
| |------ GND ------------------------ GND ----| |
|
|
| | | |
|
|
| | | |
|
|
| | | |
|
|
| |---- POWIN A00 ------. | |
|
|
| | | | |
|
|
| | 4.7k | |
|
|
| | | | |
|
|
| STM32 |--- POWOUT A01 ------.------.------ VDD ----| HYT271 |
|
|
| | | | | |
|
|
| | 2.2k | | |
|
|
| | | | | |
|
|
| |----- SDA2 B11 ------.---- | ----- SDA ----| |
|
|
| | | | |
|
|
| | 2.2k | |
|
|
| | | | |
|
|
| |----- SCL2 B10 -------------.------ SCL ----| |
|
|
| | | |
|
|
--------- -----------
|
|
|
|
DS18B20 sensor support
|
|
======================
|
|
|
|
The existing sensor configuration allows connecting several sensors of type
|
|
ds18b20 on 1wire bus number 2. The following hardware setup is necessary.::
|
|
|
|
--------- -----------
|
|
| |------ GND ----------.------------- GND ----| |
|
|
| | | |
|
|
| | | |
|
|
| | | |
|
|
| |------ VDD ----------.------------- VDD ----| |
|
|
| STM32 | | | DS18B20 |
|
|
| | 4.7k | |
|
|
| | | | |
|
|
| |----- TX2 A02 -------.------.------- DQ ----| |
|
|
| | | |
|
|
-------- -----------
|
|
|
|
USB Console support
|
|
===================
|
|
|
|
The STM32F103C8 has a USB Device controller, then we can use NuttX support
|
|
to USB Device. We can the console over USB enabling these options:
|
|
|
|
::
|
|
|
|
System Type --->
|
|
STM32 Peripheral Support --->
|
|
[*] USB Device
|
|
|
|
It will enable: CONFIG_STM32_USB=y
|
|
|
|
Board Selection --->
|
|
-*- Enable boardctl() interface
|
|
[*] Enable USB device controls
|
|
|
|
It will enable: CONFIG_BOARDCTL_USBDEVCTRL=y
|
|
|
|
Device Drivers --->
|
|
-*- USB Device Driver Support --->
|
|
[*] USB Modem (CDC/ACM) support --->
|
|
|
|
It will enable: CONFIG_CDCACM=y and many default options.
|
|
|
|
Device Drivers --->
|
|
-*- USB Device Driver Support --->
|
|
[*] USB Modem (CDC/ACM) support --->
|
|
[*] CDC/ACM console device
|
|
|
|
It will enable: CONFIG_CDCACM_CONSOLE=y
|
|
|
|
Device Drivers --->
|
|
[*] Serial Driver Support --->
|
|
Serial console (No serial console) --->
|
|
(X) No serial console
|
|
|
|
It will enable: CONFIG_NO_SERIAL_CONSOLE=y
|
|
|
|
After flashing the firmware in the board, unplug and plug it in the computer
|
|
and it will create a /dev/ttyACM0 device in the Linux. Use minicom with this
|
|
device to get access to NuttX NSH console (press Enter three times to start)
|
|
|
|
MCP2515 External Module
|
|
=======================
|
|
|
|
You can use an external MCP2515 (tested with NiRen MCP2515_CAN module) to
|
|
get CAN Bus working on STM32F103C8 chip (remember the internal CAN cannot
|
|
work with USB at same time because they share the SRAM buffer).
|
|
|
|
You can connect the MCP2515 module in the STM32F103 Minimum board this way:
|
|
connect PA5 (SPI1 CLK) to SCK; PA7 (SPI1 MOSI) to SI; PA6 (SPI MISO) to SO;
|
|
PA4 to CS; B0 to INT. Also connect 5V to VCC and GND to GND.
|
|
|
|
Note: Although MCP2515 can work with 2.7V-5.5V it is more stable when using
|
|
it on BluePill board on 5V.
|
|
|
|
Testing: you will need at least 2 boards each one with a MCP2515 module
|
|
connected to it. Connect CAN High from the first module to the CAN High of
|
|
the second module, and the CAN Low from the first module to the CAN Low of
|
|
the second module.
|
|
|
|
You need to modify the "CAN example" application on menuconfig and create
|
|
two firmware versions: the first firmware will be Read-only and the second
|
|
one Write-only. Flash the first firmware in the first board and the second
|
|
firmware in the second board. Now you can start the both boards, run the
|
|
"can" command in the Write-only board and then run the "can" command in the
|
|
Read-only board. You should see the data coming.
|
|
|
|
STM32F103 Minimum - specific Configuration Options
|
|
==================================================
|
|
|
|
..
|
|
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
|
be set to:
|
|
|
|
CONFIG_ARCH=arm
|
|
|
|
CONFIG_ARCH_family - For use in C code:
|
|
|
|
CONFIG_ARCH_ARM=y
|
|
|
|
CONFIG_ARCH_architecture - For use in C code:
|
|
|
|
CONFIG_ARCH_CORTEXM3=y
|
|
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
|
|
CONFIG_ARCH_CHIP=stm32
|
|
|
|
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
|
chip:
|
|
|
|
CONFIG_ARCH_CHIP_STM32F103C8=y
|
|
|
|
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG - Enables special STM32 clock
|
|
configuration features.
|
|
|
|
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG=n
|
|
|
|
CONFIG_ARCH_BOARD - Identifies the boards/ subdirectory and
|
|
hence, the board that supports the particular chip or SoC.
|
|
|
|
CONFIG_ARCH_BOARD=stm32f103-minimum
|
|
|
|
CONFIG_ARCH_BOARD_name - For use in C code
|
|
|
|
CONFIG_ARCH_BOARD_STM32_MINIMUM=y
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
|
of delay loops
|
|
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
|
endian)
|
|
|
|
CONFIG_RAM_SIZE - Describes the installed DRAM (SRAM in this case):
|
|
|
|
CONFIG_RAM_SIZE=20480 (20Kb)
|
|
|
|
CONFIG_RAM_START - The start address of installed DRAM
|
|
|
|
CONFIG_RAM_START=0x20000000
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
|
have LEDs
|
|
|
|
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
stack. If defined, this symbol is the size of the interrupt
|
|
stack in bytes. If not defined, the user task stacks will be
|
|
used during interrupt handling.
|
|
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
..
|
|
Individual subsystems can be enabled:
|
|
|
|
AHB
|
|
---
|
|
CONFIG_STM32_CRC
|
|
CONFIG_STM32_BKPSRAM
|
|
|
|
APB1
|
|
----
|
|
CONFIG_STM32_TIM2
|
|
CONFIG_STM32_TIM3
|
|
CONFIG_STM32_TIM4
|
|
CONFIG_STM32_WWDG
|
|
CONFIG_STM32_IWDG
|
|
CONFIG_STM32_SPI2
|
|
CONFIG_STM32_USART2
|
|
CONFIG_STM32_USART3
|
|
CONFIG_STM32_I2C1
|
|
CONFIG_STM32_I2C2
|
|
CONFIG_STM32_CAN1
|
|
CONFIG_STM32_PWR -- Required for RTC
|
|
|
|
APB2
|
|
----
|
|
CONFIG_STM32_TIM1
|
|
CONFIG_STM32_USART1
|
|
CONFIG_STM32_ADC1
|
|
CONFIG_STM32_ADC2
|
|
CONFIG_STM32_SPI1
|
|
|
|
Timer devices may be used for different purposes. One special purpose is
|
|
to generate modulated outputs for such things as motor control. If CONFIG_STM32_TIMn
|
|
is defined (as above) then the following may also be defined to indicate that
|
|
the timer is intended to be used for pulsed output modulation or ADC conversion.
|
|
Note that ADC require two definitions: Not only do you have
|
|
to assign the timer (n) for used by the ADC, but then you also have to
|
|
configure which ADC (m) it is assigned to.
|
|
|
|
CONFIG_STM32_TIMn_PWM Reserve timer n for use by PWM, n=1,..,14
|
|
CONFIG_STM32_TIMn_ADC Reserve timer n for use by ADC, n=1,..,14
|
|
CONFIG_STM32_TIMn_ADCm Reserve timer n to trigger ADCm, n=1,..,14, m=1,..,3
|
|
|
|
For each timer that is enabled for PWM usage, we need the following additional
|
|
configuration settings:
|
|
|
|
CONFIG_STM32_TIMx_CHANNEL - Specifies the timer output channel {1,..,4}
|
|
|
|
NOTE: The STM32 timers are each capable of generating different signals on
|
|
each of the four channels with different duty cycles. That capability is
|
|
not supported by this driver: Only one output channel per timer.
|
|
|
|
JTAG Enable settings (by default only SW-DP is enabled):
|
|
|
|
CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
|
|
CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
|
|
but without JNTRST.
|
|
CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled
|
|
|
|
STM32F103 Minimum specific device driver settings
|
|
|
|
CONFIG_U[S]ARTn_SERIAL_CONSOLE - selects the USARTn (n=1,2,3)
|
|
for the console and ttys0 (default is the USART1).
|
|
CONFIG_U[S]ARTn_RXBUFSIZE - Characters are buffered as received.
|
|
This specific the size of the receive buffer
|
|
CONFIG_U[S]ARTn_TXBUFSIZE - Characters are buffered before
|
|
being sent. This specific the size of the transmit buffer
|
|
CONFIG_U[S]ARTn_BAUD - The configure BAUD of the UART. Must be
|
|
CONFIG_U[S]ARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
CONFIG_U[S]ARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
CONFIG_U[S]ARTn_2STOP - Two stop bits
|
|
|
|
STM32F103 Minimum CAN Configuration
|
|
|
|
CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or
|
|
CONFIG_STM32_CAN2 must also be defined)
|
|
CONFIG_CAN_EXTID - Enables support for the 29-bit extended ID. Default
|
|
Standard 11-bit IDs.
|
|
CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages.
|
|
Default: 8
|
|
CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests.
|
|
Default: 4
|
|
CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback
|
|
mode for testing. The STM32 CAN driver does support loopback mode.
|
|
CONFIG_STM32_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1
|
|
is defined.
|
|
CONFIG_STM32_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2
|
|
is defined.
|
|
CONFIG_STM32_CAN_TSEG1 - The number of CAN time quanta in segment 1.
|
|
Default: 6
|
|
CONFIG_STM32_CAN_TSEG2 - the number of CAN time quanta in segment 2.
|
|
Default: 7
|
|
CONFIG_STM32_CAN_REGDEBUG - If CONFIG_DEBUG_FEATURES is set, this will generate an
|
|
dump of all CAN registers.
|
|
|
|
STM32F103 Minimum SPI Configuration
|
|
|
|
CONFIG_STM32_SPI_INTERRUPTS - Select to enable interrupt driven SPI
|
|
support. Non-interrupt-driven, poll-waiting is recommended if the
|
|
interrupt rate would be to high in the interrupt driven case.
|
|
CONFIG_STM32_SPIx_DMA - Use DMA to improve SPIx transfer performance.
|
|
Cannot be used with CONFIG_STM32_SPI_INTERRUPT.
|
|
|
|
Configurations
|
|
==============
|
|
|
|
Instantiating Configurations
|
|
----------------------------
|
|
|
|
Each STM32F103 Minimum configuration is maintained in a sub-directory and
|
|
can be selected as follow::
|
|
|
|
tools/configure.sh STM32F103 Minimum:<subdir>
|
|
|
|
Where <subdir> is one of the following:
|
|
|
|
Configuration Directories
|
|
-------------------------
|
|
|
|
nsh
|
|
---
|
|
|
|
Configures the NuttShell (nsh) located at apps/examples/nsh. This
|
|
configuration enables a console on UART1. Support for
|
|
builtin applications is enabled, but in the base configuration no
|
|
builtin applications are selected.
|
|
|
|
jlx12864g
|
|
---------
|
|
|
|
This is a config example to use the JLX12864G-086 LCD module. To use this
|
|
LCD you need to connect PA5 (SPI1 CLK) to SCK; PA7 (SPI1 MOSI) to SDA; PA4
|
|
to CS; PA3 to RST; PA2 to RS.
|
|
|
|
nrf24
|
|
-----
|
|
|
|
This is a config example to test the nrf24 terminal example. You will need
|
|
two stm32f103-minimum board each one with a nRF24L01 module connected this
|
|
way: connect PB1 to nRF24 CE pin; PA4 to CSN; PA5 (SPI1 CLK) to SCK; PA7
|
|
(SPI1 MOSI) to MOSI; PA6 (SPI1 MISO) to MISO; PA0 to IRQ.
|
|
|
|
usbnsh
|
|
------
|
|
|
|
This is another NSH example. If differs from other 'nsh' configurations
|
|
in that this configurations uses a USB serial device for console I/O.
|
|
|
|
NOTES:
|
|
|
|
1. This configuration uses the mconf-based configuration tool. To
|
|
change this configuration using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
2. By default, this configuration uses the ARM EABI toolchain
|
|
for Windows and builds under Cygwin (or probably MSYS). That
|
|
can easily be reconfigured, of course.
|
|
|
|
CONFIG_HOST_WINDOWS=y : Builds under Windows
|
|
CONFIG_WINDOWS_CYGWIN=y : Using Cygwin
|
|
CONFIG_ARM_TOOLCHAIN_GNU_EABI=y : GNU EABI toolchain for Windows
|
|
|
|
3. This configuration does have UART2 output enabled and set up as
|
|
the system logging device:
|
|
|
|
CONFIG_SYSLOG_CHAR=y : Use a character device for system logging
|
|
CONFIG_SYSLOG_DEVPATH="/dev/ttyS0" : UART2 will be /dev/ttyS0
|
|
|
|
However, there is nothing to generate SYSLOG output in the default
|
|
configuration so nothing should appear on UART2 unless you enable
|
|
some debug output or enable the USB monitor.
|
|
|
|
4. Enabling USB monitor SYSLOG output. If tracing is enabled, the USB
|
|
device will save encoded trace output in in-memory buffer; if the
|
|
USB monitor is enabled, that trace buffer will be periodically
|
|
emptied and dumped to the system logging device (UART2 in this
|
|
configuration)::
|
|
|
|
CONFIG_USBDEV_TRACE=y : Enable USB trace feature
|
|
CONFIG_USBDEV_TRACE_NRECORDS=128 : Buffer 128 records in memory
|
|
CONFIG_NSH_USBDEV_TRACE=n : No builtin tracing from NSH
|
|
CONFIG_NSH_ARCHINIT=y : Automatically start the USB monitor
|
|
CONFIG_USBMONITOR=y : Enable the USB monitor daemon
|
|
CONFIG_USBMONITOR_STACKSIZE=2048 : USB monitor daemon stack size
|
|
CONFIG_USBMONITOR_PRIORITY=50 : USB monitor daemon priority
|
|
CONFIG_USBMONITOR_INTERVAL=2 : Dump trace data every 2 seconds
|
|
|
|
CONFIG_USBMONITOR_TRACEINIT=y : Enable TRACE output
|
|
CONFIG_USBMONITOR_TRACECLASS=y
|
|
CONFIG_USBMONITOR_TRACETRANSFERS=y
|
|
CONFIG_USBMONITOR_TRACECONTROLLER=y
|
|
CONFIG_USBMONITOR_TRACEINTERRUPTS=y
|
|
|
|
5. By default, this project assumes that you are *NOT* using the DFU
|
|
bootloader.
|
|
|
|
Using the Prolifics PL2303 Emulation
|
|
------------------------------------
|
|
|
|
You could also use the non-standard PL2303 serial device instead of
|
|
the standard CDC/ACM serial device by changing::
|
|
|
|
CONFIG_CDCACM=y : Disable the CDC/ACM serial device class
|
|
CONFIG_CDCACM_CONSOLE=y : The CDC/ACM serial device is NOT the console
|
|
CONFIG_PL2303=y : The Prolifics PL2303 emulation is enabled
|
|
CONFIG_PL2303_CONSOLE=y : The PL2303 serial device is the console
|
|
|
|
veml6070
|
|
--------
|
|
|
|
This is a config example to use the Vishay VEML6070 UV-A sensor. To use this
|
|
sensor you need to connect PB6 (I2C1 CLK) to SCL; PB7 (I2C1 SDA) to SDA of
|
|
sensor module. I used a GY-VEML6070 module to test this driver.
|