a3f23e3275
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@4802 42af7a65-404d-4744-a932-0658087f49c3
1581 lines
58 KiB
Plaintext
1581 lines
58 KiB
Plaintext
############################################################################
|
|
# configs/pic32mx7mmb/nsh/defconfig
|
|
#
|
|
# Copyright (C) 2012 Gregory Nutt. All rights reserved.
|
|
# Author: Gregory Nutt <gnutt@nuttx.org>
|
|
#
|
|
# Redistribution and use in source and binary forms, with or without
|
|
# modification, are permitted provided that the following conditions
|
|
# are met:
|
|
#
|
|
# 1. Redistributions of source code must retain the above copyright
|
|
# notice, this list of conditions and the following disclaimer.
|
|
# 2. Redistributions in binary form must reproduce the above copyright
|
|
# notice, this list of conditions and the following disclaimer in
|
|
# the documentation and/or other materials provided with the
|
|
# distribution.
|
|
# 3. Neither the name NuttX nor the names of its contributors may be
|
|
# used to endorse or promote products derived from this software
|
|
# without specific prior written permission.
|
|
#
|
|
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
|
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
|
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
|
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
|
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
# POSSIBILITY OF SUCH DAMAGE.
|
|
#
|
|
############################################################################
|
|
#
|
|
# architecture selection
|
|
#
|
|
# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
|
|
# processor architecture.
|
|
# CONFIG_ARCH_family - for use in C code. This identifies the
|
|
# particular chip family that the architecture is implemented
|
|
# in.
|
|
# CONFIG_ARCH_architecture - for use in C code. This identifies the
|
|
# specific architecture within the chip family.
|
|
# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
# CONFIG_ARCH_CHIP_name - For use in C code
|
|
# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
|
|
# the board that supports the particular chip or SoC.
|
|
# CONFIG_ARCH_BOARD_name - for use in C code
|
|
# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
|
|
# NOTE: The PIC32MX is always little endian.
|
|
# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure
|
|
# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
|
|
# the delay actually is 100 seconds.
|
|
# CONFIG_DRAM_SIZE - Describes the installed DRAM.
|
|
# CONFIG_DRAM_START - The start address of DRAM (physical)
|
|
# CONFIG_DRAM_END - Last address+1 of installed RAM
|
|
# CONFIG_ARCH_NOINTC - define if the architecture does not
|
|
# support an interrupt controller or otherwise cannot support
|
|
# APIs like up_enable_irq() and up_disable_irq().
|
|
# CONFIG_ARCH_VECNOTIRQ - Usually the interrupt vector number provided
|
|
# to interfaces like irq_attach() and irq_detach are the same as IRQ
|
|
# numbers that are provied to IRQ management functions like
|
|
# up_enable_irq() and up_disable_irq(). But that is not true for all
|
|
# interrupt controller implementations. For example, the PIC32MX
|
|
# interrupt controller manages interrupt sources that have a many-to-one
|
|
# relationship to interrupt vectors. In such cases, CONFIG_ARCH_VECNOTIRQ
|
|
# must defined so that the OS logic will know not to assume it can use
|
|
# a vector number to enable or disable interrupts.
|
|
# CONFIG_ARCH_IRQPRIO - The PIC32MX supports interrupt prioritization
|
|
# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
# stack. If defined, this symbol is the size of the interrupt
|
|
# stack in bytes. If not defined, the user task stacks will be
|
|
# used during interrupt handling.
|
|
# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
|
|
# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
|
# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture.
|
|
# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
|
# cause a 100 second delay during boot-up. This 100 second delay
|
|
# serves no purpose other than it allows you to calibrate
|
|
# CONFIG_ARCH_DMA - Support DMA initialization
|
|
#
|
|
CONFIG_ARCH=mips
|
|
CONFIG_ARCH_MIPS=y
|
|
CONFIG_ARCH_MIPS32=y
|
|
CONFIG_ARCH_CHIP=pic32mx
|
|
CONFIG_ARCH_CHIP_PIC32MX795F512L=y
|
|
CONFIG_ARCH_BOARD=pic32mx7mmb
|
|
CONFIG_ARCH_BOARD_PIC32MX7MMB=y
|
|
CONFIG_BOARD_LOOPSPERMSEC=7245
|
|
CONFIG_DRAM_SIZE=(128*1024)
|
|
CONFIG_DRAM_START=0xa0000000
|
|
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
|
CONFIG_ARCH_NOINTC=n
|
|
CONFIG_ARCH_VECNOTIRQ=y
|
|
CONFIG_ARCH_IRQPRIO=y
|
|
CONFIG_ARCH_INTERRUPTSTACK=n
|
|
CONFIG_ARCH_STACKDUMP=y
|
|
CONFIG_ARCH_BOOTLOADER=n
|
|
CONFIG_ARCH_LEDS=y
|
|
CONFIG_ARCH_BUTTONS=n
|
|
CONFIG_ARCH_CALIBRATION=n
|
|
CONFIG_ARCH_DMA=n
|
|
|
|
#
|
|
# Enable support for RAM-based functions
|
|
# (If selected, then modifications are needed in ld.script as well)
|
|
#
|
|
CONFIG_PIC32MX_RAMFUNCS=n
|
|
|
|
#
|
|
# Identify toolchain and linker options
|
|
#
|
|
CONFIG_PIC32MX_MICROCHIPW=n
|
|
CONFIG_PIC32MX_MICROCHIPL=n
|
|
CONFIG_PIC32MX_MICROCHIPW_LITE=y
|
|
CONFIG_PIC32MX_MICROCHIPL_LITE=n
|
|
|
|
#
|
|
# Individual subsystems can be enabled:
|
|
#
|
|
|
|
CONFIG_PIC32MX_WDT=n
|
|
CONFIG_PIC32MX_RTCC=n
|
|
CONFIG_PIC32MX_TIMER1=n
|
|
CONFIG_PIC32MX_TIMER2=n
|
|
CONFIG_PIC32MX_TIMER3=n
|
|
CONFIG_PIC32MX_TIMER4=n
|
|
CONFIG_PIC32MX_TIMER5=n
|
|
CONFIG_PIC32MX_IC1=n
|
|
CONFIG_PIC32MX_IC2=n
|
|
CONFIG_PIC32MX_IC3=n
|
|
CONFIG_PIC32MX_IC4=n
|
|
CONFIG_PIC32MX_IC5=n
|
|
CONFIG_PIC32MX_OC1=n
|
|
CONFIG_PIC32MX_OC2=n
|
|
CONFIG_PIC32MX_OC3=n
|
|
CONFIG_PIC32MX_OC4=n
|
|
CONFIG_PIC32MX_OC5=n
|
|
CONFIG_PIC32MX_I2C1=n
|
|
CONFIG_PIC32MX_I2C2=n
|
|
CONFIG_PIC32MX_SPI1=y
|
|
CONFIG_PIC32MX_SPI2=n
|
|
CONFIG_PIC32MX_SPI3=n
|
|
CONFIG_PIC32MX_SPI4=n
|
|
CONFIG_PIC32MX_UART1=y
|
|
CONFIG_PIC32MX_UART2=n
|
|
CONFIG_PIC32MX_UART3=n
|
|
CONFIG_PIC32MX_UART4=n
|
|
CONFIG_PIC32MX_UART5=n
|
|
CONFIG_PIC32MX_UART6=n
|
|
CONFIG_PIC32MX_PMP=n
|
|
CONFIG_PIC32MX_ADC=n
|
|
CONFIG_PIC32MX_CVR=n
|
|
CONFIG_PIC32MX_CM1=n
|
|
CONFIG_PIC32MX_CM2=n
|
|
CONFIG_PIC32MX_OSC=y
|
|
CONFIG_PIC32MX_DDP=n
|
|
CONFIG_PIC32MX_FLASH=n
|
|
CONFIG_PIC32MX_BMX=n
|
|
CONFIG_PIC32MX_DMA=n
|
|
CONFIG_PIC32MX_CHE=n
|
|
CONFIG_PIC32MX_USBDEV=y
|
|
CONFIG_PIC32MX_USBHOST=n
|
|
CONFIG_PIC32MX_CAN1=n
|
|
CONFIG_PIC32MX_CAN2=n
|
|
CONFIG_PIC32MX_ETHERNET=y
|
|
CONFIG_PIC32MX_IOPORTA=y
|
|
CONFIG_PIC32MX_IOPORTB=y
|
|
CONFIG_PIC32MX_IOPORTC=y
|
|
CONFIG_PIC32MX_IOPORTD=y
|
|
CONFIG_PIC32MX_IOPORTE=y
|
|
CONFIG_PIC32MX_IOPORTF=y
|
|
CONFIG_PIC32MX_IOPORTG=y
|
|
|
|
#
|
|
# PIC32MX Configuration Settings
|
|
#
|
|
# DEVCFG0:
|
|
# CONFIG_PIC32MX_DEBUGGER - Background Debugger Enable. Default 3 (disabled). The
|
|
# value 2 enables.
|
|
# CONFIG_PIC32MX_ICESEL - In-Circuit Emulator/Debugger Communication Channel Select
|
|
# Default 1 (PG2)
|
|
# CONFIG_PIC32MX_PROGFLASHWP - Program FLASH write protect. Default 0xff (disabled)
|
|
# CONFIG_PIC32MX_BOOTFLASHWP - Default 1 (disabled)
|
|
# CONFIG_PIC32MX_CODEWP - Default 1 (disabled)
|
|
# DEVCFG1: (All settings determined by selections in board.h)
|
|
# DEVCFG2: (All settings determined by selections in board.h)
|
|
# DEVCFG3:
|
|
# CONFIG_PIC32MX_USBIDO - USB USBID Selection. Default 1 if USB enabled
|
|
# (USBID pin is controlled by the USB module), but 0 (GPIO) otherwise.
|
|
# CONFIG_PIC32MX_VBUSIO - USB VBUSON Selection (Default 1 if USB enabled
|
|
# (VBUSON pin is controlled by the USB module, but 0 (GPIO) otherwise.
|
|
# CONFIG_PIC32MX_WDENABLE - Enabled watchdog on power up. Default 0 (watchdog
|
|
# can be enabled later by software).
|
|
# CONFIG_PIC32MX_FETHIO: Ethernet I/O Pin Selection bit. 1 (or undefined)=
|
|
# Default Ethernet I/O Pins; 0=Alternate Ethernet I/O Pins
|
|
# CONFIG_PIC32MX_FMIIEN: Ethernet MII Enable bit. 1 (or undefined) = MII
|
|
# enabled; 0=RMII enabled
|
|
#
|
|
CONFIG_PIC32MX_DEBUGGER=2
|
|
CONFIG_PIC32MX_ICESEL=1
|
|
CONFIG_PIC32MX_FETHIO=0
|
|
CONFIG_PIC32MX_FMIIEN=0
|
|
|
|
#
|
|
# PIC32MX specific serial device driver settings
|
|
#
|
|
# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
|
# console and ttys0 (default is the UART1).
|
|
# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
|
# This specific the size of the receive buffer
|
|
# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
|
# being sent. This specific the size of the transmit buffer
|
|
# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
|
# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
# CONFIG_UARTn_2STOP - Two stop bits
|
|
#
|
|
CONFIG_UART1_SERIAL_CONSOLE=y
|
|
CONFIG_UART2_SERIAL_CONSOLE=n
|
|
CONFIG_UART3_SERIAL_CONSOLE=n
|
|
CONFIG_UART4_SERIAL_CONSOLE=n
|
|
CONFIG_UART5_SERIAL_CONSOLE=n
|
|
CONFIG_UART6_SERIAL_CONSOLE=n
|
|
|
|
CONFIG_UART1_TXBUFSIZE=256
|
|
CONFIG_UART2_TXBUFSIZE=256
|
|
CONFIG_UART3_TXBUFSIZE=256
|
|
CONFIG_UART4_TXBUFSIZE=256
|
|
CONFIG_UART5_TXBUFSIZE=256
|
|
CONFIG_UART6_TXBUFSIZE=256
|
|
|
|
CONFIG_UART1_RXBUFSIZE=256
|
|
CONFIG_UART2_RXBUFSIZE=256
|
|
CONFIG_UART3_RXBUFSIZE=256
|
|
CONFIG_UART4_RXBUFSIZE=256
|
|
CONFIG_UART5_RXBUFSIZE=256
|
|
CONFIG_UART6_RXBUFSIZE=256
|
|
|
|
CONFIG_UART1_BAUD=115200
|
|
CONFIG_UART2_BAUD=115200
|
|
CONFIG_UART3_BAUD=115200
|
|
CONFIG_UART4_BAUD=115200
|
|
CONFIG_UART5_BAUD=115200
|
|
CONFIG_UART6_BAUD=115200
|
|
|
|
CONFIG_UART1_BITS=8
|
|
CONFIG_UART2_BITS=8
|
|
CONFIG_UART3_BITS=8
|
|
CONFIG_UART4_BITS=8
|
|
CONFIG_UART5_BITS=8
|
|
CONFIG_UART6_BITS=8
|
|
|
|
CONFIG_UART1_PARITY=0
|
|
CONFIG_UART2_PARITY=0
|
|
CONFIG_UART3_PARITY=0
|
|
CONFIG_UART4_PARITY=0
|
|
CONFIG_UART5_PARITY=0
|
|
CONFIG_UART6_PARITY=0
|
|
|
|
CONFIG_UART1_2STOP=0
|
|
CONFIG_UART2_2STOP=0
|
|
CONFIG_UART3_2STOP=0
|
|
CONFIG_UART4_2STOP=0
|
|
CONFIG_UART5_2STOP=0
|
|
CONFIG_UART6_2STOP=0
|
|
|
|
#
|
|
# PIC32MX specific PHY/Ethernet device driver settings
|
|
#
|
|
# CONFIG_PHY_KS8721 - Selects the Micrel KS8721 PHY
|
|
# CONFIG_PHY_DP83848C - Selects the National Semiconduction DP83848C PHY
|
|
# CONFIG_PHY_LAN8720 - Selects the SMSC LAN8720 PHY
|
|
# CONFIG_PHY_AUTONEG - Enable auto-negotion
|
|
# CONFIG_PHY_SPEED100 - Select 100Mbit vs. 10Mbit speed.
|
|
# CONFIG_PHY_FDUPLEX - Select full (vs. half) duplex
|
|
# CONFIG_NET_NTXDESC - Configured number of Tx descriptors. Default: 2
|
|
# CONFIG_NET_NRXDESC - Configured number of Rx descriptors. Default: 4
|
|
# CONFIG_NET_PRIORITY - Ethernet interrupt priority. The is default is
|
|
# the higest priority.
|
|
# CONFIG_NET_WOL - Enable Wake-up on Lan (not fully implemented).
|
|
# CONFIG_NET_DUMPPACKET - Dump all received and transmitted packets.
|
|
# Also needs CONFIG_DEBUG.
|
|
# CONFIG_NET_REGDEBUG - Enabled low level register debug. Also needs
|
|
# CONFIG_DEBUG. Automatically enables CONFIG_NET_DESCDEBUG as well.
|
|
# CONFIG_NET_DESCDEBUG - Enabled low level descriptor debug. Also needs
|
|
# CONFIG_DEBUG.
|
|
# CONFIG_NET_DUMPPACKET - Dump all incoming and output packet contents.
|
|
# Also needs CONFIG_DEBUG.
|
|
# CONFIG_NET_HASH - Enable receipt of near-perfect match frames.
|
|
# CONFIG_NET_MULTICAST - Enable receipt of multicast (and unicast) frames.
|
|
# Automatically set if CONFIG_NET_IGMP is selected.
|
|
#
|
|
# Related DEVCFG3 Configuration Settings:
|
|
# CONFIG_PIC32MX_FETHIO: Ethernet I/O Pin Selection bit. 1 (or undefined)=
|
|
# Default Ethernet I/O Pins; 0=Alternate Ethernet I/O Pins
|
|
# CONFIG_PIC32MX_FMIIEN: Ethernet MII Enable bit. 1 (or undefined) = MII
|
|
# enabled; 0=RMII enabled
|
|
#
|
|
CONFIG_PHY_KS8721=n
|
|
CONFIG_PHY_DP83848C=n
|
|
CONFIG_PHY_LAN8720=y
|
|
CONFIG_PHY_AUTONEG=y
|
|
CONFIG_PHY_SPEED100=n
|
|
CONFIG_PHY_FDUPLEX=y
|
|
CONFIG_NET_NTXDESC=7
|
|
CONFIG_NET_NRXDESC=7
|
|
CONFIG_NET_REGDEBUG=n
|
|
CONFIG_NET_DESCDEBUG=n
|
|
CONFIG_NET_DUMPPACKET=n
|
|
|
|
#
|
|
# PIC32MX-specific USB device setup
|
|
#
|
|
CONFIG_PIC32MX_USBDEV_REGDEBUG=n
|
|
CONFIG_PIC32MX_USBDEV_BDTDEBUG=n
|
|
|
|
#
|
|
# General build options
|
|
#
|
|
# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
|
|
# BSPs from www.ridgerun.com using the tools/mkimage.sh script
|
|
# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
|
|
# used with many different loaders using the GNU objcopy program
|
|
# Should not be selected if you are not using the GNU toolchain.
|
|
# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
|
|
# used with many different loaders using the GNU objcopy program
|
|
# Should not be selected if you are not using the GNU toolchain.
|
|
# CONFIG_RAW_BINARY - make a raw binary format file used with many
|
|
# different loaders using the GNU objcopy program. This option
|
|
# should not be selected if you are not using the GNU toolchain.
|
|
# CONFIG_HAVE_LIBM - toolchain supports libm.a
|
|
#
|
|
CONFIG_RRLOAD_BINARY=n
|
|
CONFIG_INTELHEX_BINARY=y
|
|
CONFIG_MOTOROLA_SREC=n
|
|
CONFIG_RAW_BINARY=n
|
|
CONFIG_HAVE_LIBM=n
|
|
|
|
#
|
|
# General OS setup
|
|
#
|
|
# CONFIG_APPS_DIR - Identifies the relative path to the directory
|
|
# that builds the application to link with NuttX. Default: ../apps
|
|
# CONFIG_DEBUG - enables built-in debug options
|
|
# CONFIG_DEBUG_VERBOSE - enables verbose debug output
|
|
# CONFIG_DEBUG_SYMBOLS - build without optimization and with
|
|
# debug symbols (needed for use with a debugger).
|
|
# CONFIG_HAVE_CXX - Enable support for C++
|
|
# CONFIG_HAVE_CXXINITIALIZE - The platform-specific logic includes support
|
|
# for initialization of static C++ instances for this architecture
|
|
# and for the selected toolchain (via up_cxxinitialize()).
|
|
# CONFIG_MM_REGIONS - If the architecture includes multiple
|
|
# regions of memory to allocate from, this specifies the
|
|
# number of memory regions that the memory manager must
|
|
# handle and enables the API mm_addregion(start, end);
|
|
# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
|
|
# time console output
|
|
# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
|
|
# or MSEC_PER_TICK=10. This setting may be defined to
|
|
# inform NuttX that the processor hardware is providing
|
|
# system timer interrupts at some interrupt interval other
|
|
# than 10 msec.
|
|
# CONFIG_RR_INTERVAL - The round robin timeslice will be set
|
|
# this number of milliseconds; Round robin scheduling can
|
|
# be disabled by setting this value to zero.
|
|
# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in
|
|
# scheduler to monitor system performance
|
|
# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
|
|
# task name to save in the TCB. Useful if scheduler
|
|
# instrumentation is selected. Set to zero to disable.
|
|
# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
|
|
# Used to initialize the internal time logic.
|
|
# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
|
|
# You would only need this if you are concerned about accurate
|
|
# time conversions in the past or in the distant future.
|
|
# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
|
|
# would only need this if you are concerned about accurate
|
|
# time conversion in the distand past. You must also define
|
|
# CONFIG_GREGORIAN_TIME in order to use Julian time.
|
|
# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
|
|
# provides /dev/console. Enables stdout, stderr, stdin.
|
|
# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
|
|
# driver (minimul support)
|
|
# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
|
|
# errorcheck mutexes. Enables pthread_mutexattr_settype().
|
|
# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
|
|
# inheritance on mutexes and semaphores.
|
|
# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
|
|
# inheritance is enabled. It defines the maximum number of
|
|
# different threads (minus one) that can take counts on a
|
|
# semaphore with priority inheritance support. This may be
|
|
# set to zero if priority inheritance is disabled OR if you
|
|
# are only using semaphores as mutexes (only one holder) OR
|
|
# if no more than two threads participate using a counting
|
|
# semaphore.
|
|
# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled,
|
|
# then this setting is the maximum number of higher priority
|
|
# threads (minus 1) than can be waiting for another thread
|
|
# to release a count on a semaphore. This value may be set
|
|
# to zero if no more than one thread is expected to wait for
|
|
# a semaphore.
|
|
# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
|
|
# by task_create() when a new task is started. If set, all
|
|
# files/drivers will appear to be closed in the new task.
|
|
# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
|
|
# three file descriptors (stdin, stdout, stderr) by task_create()
|
|
# when a new task is started. If set, all files/drivers will
|
|
# appear to be closed in the new task except for stdin, stdout,
|
|
# and stderr.
|
|
# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
|
|
# desciptors by task_create() when a new task is started. If
|
|
# set, all sockets will appear to be closed in the new task.
|
|
# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to
|
|
# handle delayed processing from interrupt handlers. This feature
|
|
# is required for some drivers but, if there are not complaints,
|
|
# can be safely disabled. The worker thread also performs
|
|
# garbage collection -- completing any delayed memory deallocations
|
|
# from interrupt handlers. If the worker thread is disabled,
|
|
# then that clean will be performed by the IDLE thread instead
|
|
# (which runs at the lowest of priority and may not be appropriate
|
|
# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE
|
|
# is enabled, then the following options can also be used:
|
|
# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
|
|
# thread. Default: 50
|
|
# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
|
|
# work in units of microseconds. Default: 50*1000 (50 MS).
|
|
# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
|
|
# thread. Default: CONFIG_IDLETHREAD_STACKSIZE.
|
|
# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
|
|
# the worker thread. Default: 4
|
|
# CONFIG_SCHED_WAITPID - Enable the waitpid() API
|
|
# CONFIG_SCHED_ATEXIT - Enabled the atexit() API
|
|
#
|
|
#CONFIG_APPS_DIR=
|
|
|
|
CONFIG_DEBUG=n
|
|
CONFIG_DEBUG_VERBOSE=n
|
|
CONFIG_DEBUG_SYMBOLS=n
|
|
CONFIG_DEBUG_SCHED=n
|
|
CONFIG_DEBUG_USB=n
|
|
CONFIG_DEBUG_NET=n
|
|
CONFIG_DEBUG_LCD=n
|
|
CONFIG_DEBUG_GRAPHICS=n
|
|
CONFIG_DEBUG_INPUT=n
|
|
CONFIG_DEBUG_FS=n
|
|
CONFIG_DEBUG_SPI=n
|
|
CONFIG_SPI_REGDEBUG=n
|
|
|
|
CONFIG_HAVE_CXX=n
|
|
CONFIG_HAVE_CXXINITIALIZE=n
|
|
CONFIG_MM_REGIONS=1
|
|
CONFIG_ARCH_LOWPUTC=y
|
|
CONFIG_RR_INTERVAL=200
|
|
CONFIG_SCHED_INSTRUMENTATION=n
|
|
CONFIG_TASK_NAME_SIZE=0
|
|
CONFIG_START_YEAR=2012
|
|
CONFIG_START_MONTH=6
|
|
CONFIG_START_DAY=1
|
|
CONFIG_GREGORIAN_TIME=n
|
|
CONFIG_JULIAN_TIME=n
|
|
CONFIG_DEV_CONSOLE=y
|
|
CONFIG_DEV_LOWCONSOLE=n
|
|
CONFIG_MUTEX_TYPES=n
|
|
CONFIG_PRIORITY_INHERITANCE=n
|
|
CONFIG_SEM_PREALLOCHOLDERS=0
|
|
CONFIG_SEM_NNESTPRIO=0
|
|
CONFIG_FDCLONE_DISABLE=n
|
|
CONFIG_FDCLONE_STDIO=n
|
|
CONFIG_SDCLONE_DISABLE=y
|
|
CONFIG_SCHED_WORKQUEUE=n
|
|
CONFIG_SCHED_WORKPRIORITY=192
|
|
CONFIG_SCHED_WORKPERIOD=(50*1000)
|
|
CONFIG_SCHED_WORKSTACKSIZE=2048
|
|
CONFIG_SIG_SIGWORK=4
|
|
CONFIG_SCHED_WAITPID=y
|
|
CONFIG_SCHED_ATEXIT=n
|
|
|
|
#
|
|
# System Logging
|
|
#
|
|
# CONFIG_SYSLOG - Enables the System Logging feature.
|
|
# CONFIG_RAMLOG - Enables the RAM logging feature
|
|
# CONFIG_RAMLOG_CONSOLE - Use the RAM logging device as a system console.
|
|
# If this feature is enabled (along with CONFIG_DEV_CONSOLE), then all
|
|
# console output will be re-directed to a circular buffer in RAM. This
|
|
# is useful, for example, if the only console is a Telnet console. Then
|
|
# in that case, console output from non-Telnet threads will go to the
|
|
# circular buffer and can be viewed using the NSH 'dmesg' command.
|
|
# CONFIG_RAMLOG_SYSLOG - Use the RAM logging device for the syslogging
|
|
# interface. If this feature is enabled (along with CONFIG_SYSLOG),
|
|
# then all debug output (only) will be re-directed to the circular
|
|
# buffer in RAM. This RAM log can be view from NSH using the 'dmesg'
|
|
# command.
|
|
# CONFIG_RAMLOG_NPOLLWAITERS - The number of threads than can be waiting
|
|
# for this driver on poll(). Default: 4
|
|
#
|
|
# If CONFIG_RAMLOG_CONSOLE or CONFIG_RAMLOG_SYSLOG is selected, then the
|
|
# following may also be provided:
|
|
#
|
|
# CONFIG_RAMLOG_CONSOLE_BUFSIZE - Size of the console RAM log. Default: 1024
|
|
#
|
|
|
|
CONFIG_SYSLOG=n
|
|
CONFIG_RAMLOG=n
|
|
CONFIG_RAMLOG_CONSOLE=n
|
|
CONFIG_RAMLOG_SYSLOG=n
|
|
#CONFIG_RAMLOG_NPOLLWAITERS
|
|
#CONFIG_RAMLOG_CONSOLE_BUFSIZE
|
|
|
|
#
|
|
# Settings for NXFLAT
|
|
#
|
|
# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
|
|
# This format will support execution of NuttX binaries located
|
|
# in a ROMFS filesystem (see examples/nxflat).
|
|
# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals
|
|
# with. CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and
|
|
# CONFIG_DEBUG_BINFMT have to be defined or
|
|
# CONFIG_NXFLAT_DUMPBUFFER does nothing.
|
|
# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table
|
|
# is ordered by symbol name
|
|
#
|
|
CONFIG_NXFLAT=n
|
|
CONFIG_NXFLAT_DUMPBUFFER=n
|
|
CONFIG_SYMTAB_ORDEREDBYNAME=y
|
|
|
|
#
|
|
# The following can be used to disable categories of
|
|
# APIs supported by the OS. If the compiler supports
|
|
# weak functions, then it should not be necessary to
|
|
# disable functions unless you want to restrict usage
|
|
# of those APIs.
|
|
#
|
|
# There are certain dependency relationships in these
|
|
# features.
|
|
#
|
|
# o mq_notify logic depends on signals to awaken tasks
|
|
# waiting for queues to become full or empty.
|
|
# o pthread_condtimedwait() depends on signals to wake
|
|
# up waiting tasks.
|
|
#
|
|
CONFIG_DISABLE_CLOCK=n
|
|
CONFIG_DISABLE_POSIX_TIMERS=n
|
|
CONFIG_DISABLE_PTHREAD=n
|
|
CONFIG_DISABLE_SIGNALS=n
|
|
CONFIG_DISABLE_MQUEUE=n
|
|
CONFIG_DISABLE_MOUNTPOINT=n
|
|
CONFIG_DISABLE_ENVIRON=n
|
|
CONFIG_DISABLE_POLL=y
|
|
|
|
#
|
|
# Misc libc settings
|
|
#
|
|
# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
|
|
# little smaller if we do not support fieldwidthes
|
|
#
|
|
CONFIG_NOPRINTF_FIELDWIDTH=n
|
|
|
|
#
|
|
# Allow for architecture optimized implementations
|
|
#
|
|
# The architecture can provide optimized versions of the
|
|
# following to improve system performance
|
|
#
|
|
CONFIG_ARCH_MEMCPY=n
|
|
CONFIG_ARCH_MEMCMP=n
|
|
CONFIG_ARCH_MEMMOVE=n
|
|
CONFIG_ARCH_MEMSET=n
|
|
CONFIG_ARCH_STRCMP=n
|
|
CONFIG_ARCH_STRCPY=n
|
|
CONFIG_ARCH_STRNCPY=n
|
|
CONFIG_ARCH_STRLEN=n
|
|
CONFIG_ARCH_STRNLEN=n
|
|
CONFIG_ARCH_BZERO=n
|
|
|
|
#
|
|
# Sizes of configurable things (0 disables)
|
|
#
|
|
# CONFIG_MAX_TASKS - The maximum number of simultaneously
|
|
# active tasks. This value must be a power of two.
|
|
# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
|
|
# of parameters that a task may receive (i.e., maxmum value
|
|
# of 'argc')
|
|
# CONFIG_NPTHREAD_KEYS - The number of items of thread-
|
|
# specific data that can be retained
|
|
# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
|
|
# descriptors (one for each open)
|
|
# CONFIG_NFILE_STREAMS - The maximum number of streams that
|
|
# can be fopen'ed
|
|
# CONFIG_NAME_MAX - The maximum size of a file name.
|
|
# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
|
|
# on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
|
|
# CONFIG_STDIO_LINEBUFFER - If standard C buffered I/O is enabled
|
|
# (CONFIG_STDIO_BUFFER_SIZE > 0), then this option may be added
|
|
# to force automatic, line-oriented flushing the output buffer
|
|
# for putc(), fputc(), putchar(), puts(), fputs(), printf(),
|
|
# fprintf(), and vfprintf(). When a newline is encountered in
|
|
# the output string, the output buffer will be flushed. This
|
|
# (slightly) increases the NuttX footprint but supports the kind
|
|
# of behavior that people expect for printf().
|
|
# CONFIG_NUNGET_CHARS - Number of characters that can be
|
|
# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
|
|
# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
|
|
# structures. The system manages a pool of preallocated
|
|
# message structures to minimize dynamic allocations
|
|
# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
|
|
# a fixed payload size given by this settin (does not include
|
|
# other message structure overhead.
|
|
# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
|
|
# can be passed to a watchdog handler
|
|
# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
|
|
# structures. The system manages a pool of preallocated
|
|
# watchdog structures to minimize dynamic allocations
|
|
# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
|
|
# timer structures. The system manages a pool of preallocated
|
|
# timer structures to minimize dynamic allocations. Set to
|
|
# zero for all dynamic allocations.
|
|
#
|
|
CONFIG_MAX_TASKS=16
|
|
CONFIG_MAX_TASK_ARGS=4
|
|
CONFIG_NPTHREAD_KEYS=4
|
|
CONFIG_NFILE_DESCRIPTORS=8
|
|
CONFIG_NFILE_STREAMS=8
|
|
CONFIG_NAME_MAX=32
|
|
CONFIG_STDIO_BUFFER_SIZE=64
|
|
CONFIG_STDIO_LINEBUFFER=y
|
|
CONFIG_NUNGET_CHARS=2
|
|
CONFIG_PREALLOC_MQ_MSGS=4
|
|
CONFIG_MQ_MAXMSGSIZE=32
|
|
CONFIG_MAX_WDOGPARMS=2
|
|
CONFIG_PREALLOC_WDOGS=8
|
|
CONFIG_PREALLOC_TIMERS=4
|
|
|
|
#
|
|
# Framebuffer driver options
|
|
#
|
|
CONFIG_FB_CMAP=n
|
|
CONFIG_FB_HWCURSOR=n
|
|
CONFIG_FB_HWCURSORIMAGE=n
|
|
#CONFIG_FB_HWCURSORSIZE
|
|
#CONFIG_FB_TRANSPARENCY
|
|
|
|
#
|
|
# Framebuffer driver options
|
|
#
|
|
CONFIG_FB_CMAP=n
|
|
CONFIG_FB_HWCURSOR=n
|
|
CONFIG_FB_HWCURSORIMAGE=n
|
|
#CONFIG_FB_HWCURSORSIZE
|
|
#CONFIG_FB_TRANSPARENCY
|
|
|
|
#
|
|
# Filesystem configuration
|
|
#
|
|
# CONFIG_FS_FAT - Enable FAT filesystem support
|
|
# CONFIG_FAT_SECTORSIZE - Max supported sector size
|
|
# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
|
|
# file name support.
|
|
# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims
|
|
# patents on FAT long file name technology. Please read the
|
|
# disclaimer in the top-level COPYING file and only enable this
|
|
# feature if you understand these issues.
|
|
# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
|
|
# default, maximum long file name is 255 bytes. This can eat up
|
|
# a lot of memory (especially stack space). If you are willing
|
|
# to live with some non-standard, short long file names, then
|
|
# define this value. A good choice would be the same value as
|
|
# selected for CONFIG_NAME_MAX which will limit the visibility
|
|
# of longer file names anyway.
|
|
# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
|
|
# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH.
|
|
# This must have one of the values of 0xff or 0x00.
|
|
# Default: 0xff.
|
|
# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
|
|
# don't both with file chunks smaller than this number of data bytes.
|
|
# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
|
|
# Default: 255.
|
|
# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
|
|
# don't both with file chunks smaller than this number of data bytes.
|
|
# Default: 32.
|
|
# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
|
|
# packing files together toward the end of the file or, if file are
|
|
# deleted at the end of the file, clean up can simply mean erasing
|
|
# the end of FLASH memory so that it can be re-used again. However,
|
|
# doing this can also harm the life of the FLASH part because it can
|
|
# mean that the tail end of the FLASH is re-used too often. This
|
|
# threshold determines if/when it is worth erased the tail end of FLASH
|
|
# and making it available for re-use (and possible over-wear).
|
|
# Default: 8192.
|
|
# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
|
|
# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
|
|
# option will enable a limited form of memory mapping that is
|
|
# implemented by copying whole files into memory.
|
|
#
|
|
CONFIG_FS_FAT=y
|
|
CONFIG_FAT_LCNAMES=y
|
|
CONFIG_FAT_LFN=y
|
|
CONFIG_FAT_MAXFNAME=32
|
|
CONFIG_FS_NXFFS=n
|
|
CONFIG_FS_ROMFS=n
|
|
|
|
#
|
|
# SPI-based MMC/SD driver
|
|
#
|
|
# CONFIG_MMCSD_NSLOTS
|
|
# Number of MMC/SD slots supported by the driver
|
|
# CONFIG_MMCSD_READONLY
|
|
# Provide read-only access (default is read/write)
|
|
# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
|
|
# Default is 20MHz.
|
|
#
|
|
CONFIG_MMCSD_NSLOTS=1
|
|
CONFIG_MMCSD_READONLY=n
|
|
CONFIG_MMCSD_SPICLOCK=12500000
|
|
|
|
#
|
|
# Block driver buffering
|
|
#
|
|
# CONFIG_FS_READAHEAD
|
|
# Enable read-ahead buffering
|
|
# CONFIG_FS_WRITEBUFFER
|
|
# Enable write buffering
|
|
#
|
|
CONFIG_FS_READAHEAD=n
|
|
CONFIG_FS_WRITEBUFFER=n
|
|
|
|
#
|
|
# SDIO-based MMC/SD driver
|
|
#
|
|
# CONFIG_SDIO_DMA
|
|
# SDIO driver supports DMA
|
|
# CONFIG_MMCSD_MMCSUPPORT
|
|
# Enable support for MMC cards
|
|
# CONFIG_MMCSD_HAVECARDDETECT
|
|
# SDIO driver card detection is 100% accurate
|
|
#
|
|
CONFIG_SDIO_DMA=n
|
|
CONFIG_MMCSD_MMCSUPPORT=n
|
|
CONFIG_MMCSD_HAVECARDDETECT=n
|
|
|
|
#
|
|
# TCP/IP and UDP support via uIP
|
|
#
|
|
# CONFIG_NET - Enable or disable all network features
|
|
# CONFIG_NET_NOINTS -- CONFIG_NET_NOINT indicates that uIP not called from
|
|
# the interrupt level. If CONFIG_NET_NOINTS is defined, critical sections
|
|
# will be managed with semaphores; Otherwise, it assumed that uIP will be
|
|
# called from interrupt level handling and critical sections will be
|
|
# managed by enabling and disabling interrupts.
|
|
# CONFIG_NET_MULTIBUFFER - Traditionally, uIP has used a single buffer
|
|
# for all incoming and outgoing traffic. If this configuration is
|
|
# selected, then the driver can manage multiple I/O buffers and can,
|
|
# for example, be filling one input buffer while sending another
|
|
# output buffer. Or, as another example, the driver may support
|
|
# queuing of concurrent input/ouput and output transfers for better
|
|
# performance.
|
|
# CONFIG_NET_IPv6 - Build in support for IPv6
|
|
# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
|
|
# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
|
|
# CONFIG_NET_BUFSIZE - uIP buffer size
|
|
# CONFIG_NET_TCP - TCP support on or off
|
|
# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
|
|
# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
|
|
# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
|
|
# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
|
|
# accept() is called. The size of the backlog is selected when listen() is called.
|
|
# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
|
|
# CONFIG_NET_UDP - UDP support on or off
|
|
# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
|
|
# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
|
|
# CONFIG_NET_ICMP - ICMP ping response support on or off
|
|
# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
|
|
# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
|
|
# CONFIG_NET_STATISTICS - uIP statistics on or off
|
|
# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
|
|
# CONFIG_NET_BROADCAST - Broadcast support
|
|
# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
|
|
# CONFIG_NET_ARP_IPIN - Harvest IP/MAC address mappings from the ARP table
|
|
# from incoming IP packets.
|
|
# CONFIG_NET_MULTICAST - Outgoing multi-cast address support
|
|
# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when
|
|
# looking for duplicates
|
|
#
|
|
CONFIG_NET=y
|
|
CONFIG_NET_NOINTS=n
|
|
CONFIG_NET_MULTIBUFFER=y
|
|
CONFIG_NET_IPv6=n
|
|
CONFIG_NSOCKET_DESCRIPTORS=10
|
|
CONFIG_NET_SOCKOPTS=y
|
|
CONFIG_NET_BUFSIZE=562
|
|
CONFIG_NET_TCP=y
|
|
CONFIG_NET_TCP_CONNS=40
|
|
#CONFIG_NET_TCP_READAHEAD_BUFSIZE
|
|
CONFIG_NET_NTCP_READAHEAD_BUFFERS=16
|
|
CONFIG_NET_TCPBACKLOG=y
|
|
CONFIG_NET_MAX_LISTENPORTS=40
|
|
CONFIG_NET_UDP=y
|
|
CONFIG_NET_UDP_CHECKSUMS=y
|
|
#CONFIG_NET_UDP_CONNS=10
|
|
CONFIG_NET_ICMP=y
|
|
CONFIG_NET_ICMP_PING=y
|
|
#CONFIG_NET_PINGADDRCONF=0
|
|
CONFIG_NET_STATISTICS=n
|
|
#CONFIG_NET_RECEIVE_WINDOW=
|
|
CONFIG_NET_BROADCAST=n
|
|
#CONFIG_NET_ARPTAB_SIZE=8
|
|
CONFIG_NET_ARP_IPIN=n
|
|
CONFIG_NET_MULTICAST=n
|
|
#CONFIG_NET_FWCACHE_SIZE=2
|
|
|
|
#
|
|
# UIP Network Utilities
|
|
# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
|
|
# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
|
|
#
|
|
CONFIG_NET_DHCP_LIGHT=n
|
|
CONFIG_NET_RESOLV_ENTRIES=4
|
|
|
|
#
|
|
# FTP Server
|
|
#
|
|
# CONFIG_FTPD_VENDORID - The vendor name to use in FTP communications.
|
|
# Default: "NuttX"
|
|
# CONFIG_FTPD_SERVERID - The server name to use in FTP communications.
|
|
# Default: "NuttX FTP Server"
|
|
# CONFIG_FTPD_CMDBUFFERSIZE - The maximum size of one command. Default:
|
|
# 128 bytes.
|
|
# CONFIG_FTPD_DATABUFFERSIZE - The size of the I/O buffer for data
|
|
# transfers. Default: 512 bytes.
|
|
# CONFIG_FTPD_WORKERSTACKSIZE - The stacksize to allocate for each
|
|
# FTP daemon worker thread. Default: 2048 bytes.
|
|
#
|
|
# Other required configuration settings: Of course TCP networking support
|
|
# is required. But here are a couple that are less obvious:
|
|
#
|
|
# CONFIG_DISABLE_PTHREAD - pthread support is required
|
|
# CONFIG_DISABLE_POLL - poll() support is required
|
|
#
|
|
CONFIG_FTPD_CMDBUFFERSIZE=512
|
|
CONFIG_FTPD_DATABUFFERSIZE=2048
|
|
|
|
#
|
|
# Input device configuration
|
|
#
|
|
CONFIG_INPUT=n
|
|
CONFIG_INPUT_TSC2007=n
|
|
CONFIG_INPUT_STMPE811=n
|
|
|
|
#
|
|
# USB Device Configuration
|
|
#
|
|
# CONFIG_USBDEV
|
|
# Enables USB device support
|
|
# CONFIG_USBDEV_ISOCHRONOUS
|
|
# Build in extra support for isochronous endpoints
|
|
# CONFIG_USBDEV_DUALSPEED
|
|
# Hardware handles high and full speed operation (USB 2.0)
|
|
# CONFIG_USBDEV_SELFPOWERED
|
|
# Will cause USB features to indicate that the device is
|
|
# self-powered
|
|
# CONFIG_USBDEV_MAXPOWER
|
|
# Maximum power consumption in mA
|
|
# CONFIG_USBDEV_TRACE
|
|
# Enables USB tracing for debug
|
|
# CONFIG_USBDEV_TRACE_NRECORDS
|
|
# Number of trace entries to remember
|
|
#
|
|
CONFIG_USBDEV=y
|
|
CONFIG_USBDEV_ISOCHRONOUS=n
|
|
CONFIG_USBDEV_DUALSPEED=n
|
|
CONFIG_USBDEV_SELFPOWERED=y
|
|
CONFIG_USBDEV_REMOTEWAKEUP=n
|
|
CONFIG_USBDEV_MAXPOWER=100
|
|
CONFIG_USBDEV_TRACE=n
|
|
CONFIG_USBDEV_TRACE_NRECORDS=128
|
|
|
|
#
|
|
# USB Serial Device Configuration
|
|
#
|
|
# CONFIG_PL2303
|
|
# Enable compilation of the USB serial driver
|
|
# CONFIG_PL2303_EPINTIN
|
|
# The logical 7-bit address of a hardware endpoint that supports
|
|
# interrupt IN operation
|
|
# CONFIG_PL2303_EPBULKOUT
|
|
# The logical 7-bit address of a hardware endpoint that supports
|
|
# bulk OUT operation
|
|
# CONFIG_PL2303_EPBULKIN
|
|
# The logical 7-bit address of a hardware endpoint that supports
|
|
# bulk IN operation
|
|
# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS
|
|
# The number of write/read requests that can be in flight
|
|
# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR
|
|
# The vendor ID code/string
|
|
# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR
|
|
# The product ID code/string
|
|
# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE
|
|
# Size of the serial receive/transmit buffers
|
|
#
|
|
CONFIG_PL2303=n
|
|
CONFIG_PL2303_EPINTIN=1
|
|
CONFIG_PL2303_EPBULKOUT=2
|
|
CONFIG_PL2303_EPBULKIN=3
|
|
CONFIG_PL2303_NWRREQS=4
|
|
CONFIG_PL2303_NRDREQS=4
|
|
CONFIG_PL2303_VENDORID=0x067b
|
|
CONFIG_PL2303_PRODUCTID=0x2303
|
|
CONFIG_PL2303_VENDORSTR="Nuttx"
|
|
CONFIG_PL2303_PRODUCTSTR="USBdev Serial"
|
|
CONFIG_PL2303_RXBUFSIZE=512
|
|
CONFIG_PL2303_TXBUFSIZE=512
|
|
|
|
#
|
|
# USB serial device class driver (Standard CDC ACM class)
|
|
#
|
|
# CONFIG_CDCACM
|
|
# Enable compilation of the USB serial driver
|
|
# CONFIG_CDCACM_CONSOLE
|
|
# Configures the CDC/ACM serial port as the console device.
|
|
# CONFIG_CDCACM_EP0MAXPACKET
|
|
# Endpoint 0 max packet size. Default 64
|
|
# CONFIG_CDCACM_EPINTIN
|
|
# The logical 7-bit address of a hardware endpoint that supports
|
|
# interrupt IN operation. Default 2.
|
|
# CONFIG_CDCACM_EPINTIN_FSSIZE
|
|
# Max package size for the interrupt IN endpoint if full speed mode.
|
|
# Default 64.
|
|
# CONFIG_CDCACM_EPINTIN_HSSIZE
|
|
# Max package size for the interrupt IN endpoint if high speed mode.
|
|
# Default 64
|
|
# CONFIG_CDCACM_EPBULKOUT
|
|
# The logical 7-bit address of a hardware endpoint that supports
|
|
# bulk OUT operation
|
|
# CONFIG_CDCACM_EPBULKOUT_FSSIZE
|
|
# Max package size for the bulk OUT endpoint if full speed mode.
|
|
# Default 64.
|
|
# CONFIG_CDCACM_EPBULKOUT_HSSIZE
|
|
# Max package size for the bulk OUT endpoint if high speed mode.
|
|
# Default 512.
|
|
# CONFIG_CDCACM_EPBULKIN
|
|
# The logical 7-bit address of a hardware endpoint that supports
|
|
# bulk IN operation
|
|
# CONFIG_CDCACM_EPBULKIN_FSSIZE
|
|
# Max package size for the bulk IN endpoint if full speed mode.
|
|
# Default 64.
|
|
# CONFIG_CDCACM_EPBULKIN_HSSIZE
|
|
# Max package size for the bulk IN endpoint if high speed mode.
|
|
# Default 512.
|
|
# CONFIG_CDCACM_NWRREQS and CONFIG_CDCACM_NRDREQS
|
|
# The number of write/read requests that can be in flight.
|
|
# Default 256.
|
|
# CONFIG_CDCACM_VENDORID and CONFIG_CDCACM_VENDORSTR
|
|
# The vendor ID code/string. Default 0x0525 and "NuttX"
|
|
# 0x0525 is the Netchip vendor and should not be used in any
|
|
# products. This default VID was selected for compatibility with
|
|
# the Linux CDC ACM default VID.
|
|
# CONFIG_CDCACM_PRODUCTID and CONFIG_CDCACM_PRODUCTSTR
|
|
# The product ID code/string. Default 0xa4a7 and "CDC/ACM Serial"
|
|
# 0xa4a7 was selected for compatibility with the Linux CDC ACM
|
|
# default PID.
|
|
# CONFIG_CDCACM_RXBUFSIZE and CONFIG_CDCACM_TXBUFSIZE
|
|
# Size of the serial receive/transmit buffers. Default 256.
|
|
#
|
|
CONFIG_CDCACM=n
|
|
CONFIG_CDCACM_CONSOLE=n
|
|
#CONFIG_CDCACM_EP0MAXPACKET
|
|
#CONFIG_CDCACM_EPINTIN
|
|
#CONFIG_CDCACM_EPINTIN_FSSIZE
|
|
#CONFIG_CDCACM_EPINTIN_HSSIZE
|
|
#CONFIG_CDCACM_EPBULKOUT
|
|
#CONFIG_CDCACM_EPBULKOUT_FSSIZE
|
|
#CONFIG_CDCACM_EPBULKOUT_HSSIZE
|
|
#CONFIG_CDCACM_EPBULKIN
|
|
#CONFIG_CDCACM_EPBULKIN_FSSIZE
|
|
#CONFIG_CDCACM_EPBULKIN_HSSIZE
|
|
#CONFIG_CDCACM_NWRREQS
|
|
#CONFIG_CDCACM_NRDREQS
|
|
#CONFIG_CDCACM_VENDORID
|
|
#CONFIG_CDCACM_VENDORSTR
|
|
#CONFIG_CDCACM_PRODUCTID
|
|
#CONFIG_CDCACM_PRODUCTSTR
|
|
#CONFIG_CDCACM_RXBUFSIZE
|
|
#CONFIG_CDCACM_TXBUFSIZE
|
|
|
|
#
|
|
# USB Storage Device Configuration
|
|
#
|
|
# CONFIG_USBMSC
|
|
# Enable compilation of the USB storage driver
|
|
# CONFIG_USBMSC_EP0MAXPACKET
|
|
# Max packet size for endpoint 0
|
|
# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN
|
|
# The logical 7-bit address of a hardware endpoints that support
|
|
# bulk OUT and IN operations
|
|
# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS
|
|
# The number of write/read requests that can be in flight
|
|
# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN
|
|
# The size of the buffer in each write/read request. This
|
|
# value needs to be at least as large as the endpoint
|
|
# maxpacket and ideally as large as a block device sector.
|
|
# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR
|
|
# The vendor ID code/string
|
|
# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR
|
|
# The product ID code/string
|
|
# CONFIG_USBMSC_REMOVABLE
|
|
# Select if the media is removable
|
|
#
|
|
CONFIG_USBMSC=y
|
|
CONFIG_USBMSC_EP0MAXPACKET=64
|
|
CONFIG_USBMSC_EPBULKOUT=1
|
|
CONFIG_USBMSC_EPBULKIN=2
|
|
CONFIG_USBMSC_NRDREQS=8
|
|
CONFIG_USBMSC_NWRREQS=2
|
|
CONFIG_USBMSC_BULKINREQLEN=256
|
|
CONFIG_USBMSC_BULKOUTREQLEN=64
|
|
CONFIG_USBMSC_VENDORID=0x584e
|
|
CONFIG_USBMSC_VENDORSTR="NuttX"
|
|
CONFIG_USBMSC_PRODUCTID=0x5342
|
|
CONFIG_USBMSC_PRODUCTSTR="USBdev Storage"
|
|
CONFIG_USBMSC_VERSIONNO=0x0399
|
|
CONFIG_USBMSC_REMOVABLE=y
|
|
|
|
#
|
|
# Graphics related configuration settings
|
|
#
|
|
# CONFIG_NX
|
|
# Enables overall support for graphics library and NX
|
|
# CONFIG_NX_MULTIUSER
|
|
# Configures NX in multi-user mode
|
|
# CONFIG_NX_NPLANES
|
|
# Some YUV color formats requires support for multiple planes,
|
|
# one for each color component. Unless you have such special
|
|
# hardware, this value should be undefined or set to 1
|
|
# CONFIG_NX_DISABLE_1BPP, CONFIG_NX_DISABLE_2BPP,
|
|
# CONFIG_NX_DISABLE_4BPP, CONFIG_NX_DISABLE_8BPP,
|
|
# CONFIG_NX_DISABLE_16BPP, CONFIG_NX_DISABLE_24BPP, and
|
|
# CONFIG_NX_DISABLE_32BPP
|
|
# NX supports a variety of pixel depths. You can save some
|
|
# memory by disabling support for unused color depths.
|
|
# CONFIG_NX_PACKEDMSFIRST
|
|
# If a pixel depth of less than 8-bits is used, then NX needs
|
|
# to know if the pixels pack from the MS to LS or from LS to MS
|
|
# CONFIG_NX_LCDDRIVER
|
|
# By default, NX builds to use a framebuffer driver (see
|
|
# include/nuttx/fb.h). If this option is defined, NX will
|
|
# build to use an LCD driver (see include/nuttx/lcd/lcd.h).
|
|
# CONFIG_LCD_MAXPOWER - The full-on power setting for an LCD device.
|
|
# CONFIG_LCD_MAXCONTRAST - The maximum contrast value for an LCD device.
|
|
# CONFIG_NX_MOUSE
|
|
# Build in support for mouse input
|
|
# CONFIG_NX_KBD
|
|
# Build in support of keypad/keyboard input
|
|
# CONFIG_NXTK_BORDERWIDTH
|
|
# Specifies with with of the border (in pixels) used with
|
|
# framed windows. The default is 4.
|
|
# CONFIG_NXTK_BORDERCOLOR1, CONFIG_NXTK_BORDERCOLOR2, CONFIG_NXTK_BORDERCOLOR3
|
|
# Specify the colors of the border used with framed windows.
|
|
# CONFIG_NXTK_BORDERCOLOR2 is the shadow side color and so is normally darker.
|
|
# CONFIG_NXTK_BORDERCOLOR3 is the shiny side color and so is normally brighter.
|
|
# The default is mediumdark grey, and light grey, respectively
|
|
# CONFIG_NXTK_AUTORAISE
|
|
# If set, a window will be raised to the top if the mouse position
|
|
# is over a visible portion of the window. Default: A mouse
|
|
# button must be clicked over a visible portion of the window.
|
|
# CONFIG_NXFONTS_CHARBITS
|
|
# The number of bits in the character set. Current options are
|
|
# only 7 and 8. The default is 7.
|
|
# CONFIG_NXFONT_SANS17X22
|
|
# This option enables support for a tiny, 17x22 san serif font
|
|
# (font ID FONTID_SANS17X22 == 14).
|
|
# CONFIG_NXFONT_SANS20X26
|
|
# This option enables support for a tiny, 20x26 san serif font
|
|
# (font ID FONTID_SANS20X26 == 15).
|
|
# CONFIG_NXFONT_SANS23X27
|
|
# This option enables support for a tiny, 23x27 san serif font
|
|
# (font ID FONTID_SANS23X27 == 1).
|
|
# CONFIG_NXFONT_SANS22X29
|
|
# This option enables support for a small, 22x29 san serif font
|
|
# (font ID FONTID_SANS22X29 == 2).
|
|
# CONFIG_NXFONT_SANS28X37
|
|
# This option enables support for a medium, 28x37 san serif font
|
|
# (font ID FONTID_SANS28X37 == 3).
|
|
# CONFIG_NXFONT_SANS39X48
|
|
# This option enables support for a large, 39x48 san serif font
|
|
# (font ID FONTID_SANS39X48 == 4).
|
|
# CONFIG_NXFONT_SANS17X23B
|
|
# This option enables support for a tiny, 17x23 san serif bold font
|
|
# (font ID FONTID_SANS17X23B == 16).
|
|
# CONFIG_NXFONT_SANS20X27B
|
|
# This option enables support for a tiny, 20x27 san serif bold font
|
|
# (font ID FONTID_SANS20X27B == 17).
|
|
# CONFIG_NXFONT_SANS22X29B
|
|
# This option enables support for a small, 22x29 san serif bold font
|
|
# (font ID FONTID_SANS22X29B == 5).
|
|
# CONFIG_NXFONT_SANS28X37B
|
|
# This option enables support for a medium, 28x37 san serif bold font
|
|
# (font ID FONTID_SANS28X37B == 6).
|
|
# CONFIG_NXFONT_SANS40X49B
|
|
# This option enables support for a large, 40x49 san serif bold font
|
|
# (font ID FONTID_SANS40X49B == 7).
|
|
# CONFIG_NXFONT_SERIF22X29
|
|
# This option enables support for a small, 22x29 font (with serifs)
|
|
# (font ID FONTID_SERIF22X29 == 8).
|
|
# CONFIG_NXFONT_SERIF29X37
|
|
# This option enables support for a medium, 29x37 font (with serifs)
|
|
# (font ID FONTID_SERIF29X37 == 9).
|
|
# CONFIG_NXFONT_SERIF38X48
|
|
# This option enables support for a large, 38x48 font (with serifs)
|
|
# (font ID FONTID_SERIF38X48 == 10).
|
|
# CONFIG_NXFONT_SERIF22X28B
|
|
# This option enables support for a small, 27x38 bold font (with serifs)
|
|
# (font ID FONTID_SERIF22X28B == 11).
|
|
# CONFIG_NXFONT_SERIF27X38B
|
|
# This option enables support for a medium, 27x38 bold font (with serifs)
|
|
# (font ID FONTID_SERIF27X38B == 12).
|
|
# CONFIG_NXFONT_SERIF38X49B
|
|
# This option enables support for a large, 38x49 bold font (with serifs)
|
|
# (font ID FONTID_SERIF38X49B == 13).
|
|
#
|
|
# NX Multi-user only options:
|
|
#
|
|
# CONFIG_NX_BLOCKING
|
|
# Open the client message queues in blocking mode. In this case,
|
|
# nx_eventhandler() will not return until a message is received and processed.
|
|
# CONFIG_NX_MXSERVERMSGS and CONFIG_NX_MXCLIENTMSGS
|
|
# Specifies the maximum number of messages that can fit in
|
|
# the message queues. No additional resources are allocated, but
|
|
# this can be set to prevent flooding of the client or server with
|
|
# too many messages (CONFIG_PREALLOC_MQ_MSGS controls how many
|
|
# messages are pre-allocated).
|
|
#
|
|
CONFIG_NX=n
|
|
CONFIG_NX_MULTIUSER=n
|
|
CONFIG_NX_NPLANES=1
|
|
CONFIG_NX_DISABLE_1BPP=y
|
|
CONFIG_NX_DISABLE_2BPP=y
|
|
CONFIG_NX_DISABLE_4BPP=y
|
|
CONFIG_NX_DISABLE_8BPP=y
|
|
CONFIG_NX_DISABLE_16BPP=n
|
|
CONFIG_NX_DISABLE_24BPP=y
|
|
CONFIG_NX_DISABLE_32BPP=y
|
|
CONFIG_NX_PACKEDMSFIRST=n
|
|
CONFIG_NX_LCDDRIVER=y
|
|
CONFIG_LCD_MAXPOWER=255
|
|
CONFIG_LCD_MAXCONTRAST=1
|
|
CONFIG_NX_MOUSE=y
|
|
CONFIG_NX_KBD=y
|
|
#CONFIG_NXTK_BORDERWIDTH=4
|
|
CONFIG_NXTK_BORDERCOLOR1=0x5cb7
|
|
CONFIG_NXTK_BORDERCOLOR2=0x21c9
|
|
CONFIG_NXTK_BORDERCOLOR3=0xffdf
|
|
CONFIG_NXTK_AUTORAISE=n
|
|
CONFIG_NXFONT_SANS17X22=n
|
|
CONFIG_NXFONT_SANS20X26=n
|
|
CONFIG_NXFONT_SANS22X29=n
|
|
CONFIG_NXFONT_SANS23X27=y
|
|
CONFIG_NXFONT_SANS28X37=n
|
|
CONFIG_NXFONT_SANS17X23B=n
|
|
CONFIG_NXFONT_SANS20X27B=n
|
|
CONFIG_NXFONT_SANS22X29B=y
|
|
CONFIG_NXFONT_SANS28X37B=n
|
|
CONFIG_NXFONT_SANS40X49B=n
|
|
CONFIG_NXFONT_SERIF22X29=n
|
|
CONFIG_NXFONT_SERIF29X37=n
|
|
CONFIG_NXFONT_SERIF38X48=n
|
|
CONFIG_NXFONT_SERIF22X28B=n
|
|
CONFIG_NXFONT_SERIF27X38B=n
|
|
CONFIG_NXFONT_SERIF38X49B=n
|
|
CONFIG_NXFONTS_CHARBITS=7
|
|
CONFIG_NX_BLOCKING=y
|
|
CONFIG_NX_MXSERVERMSGS=32
|
|
CONFIG_NX_MXCLIENTMSGS=16
|
|
|
|
#
|
|
# NxConsole Configuration Settings:
|
|
#
|
|
# CONFIG_NXCONSOLE
|
|
# Enables building of the NxConsole driver.
|
|
# CONFIG_NXCONSOLE_BPP
|
|
# Currently, NxConsole supports only a single pixel depth. This
|
|
# configuration setting must be provided to support that single pixel depth.
|
|
# Default: The smallest enabled pixel depth. (see CONFIG_NX_DISABLE_*BPP)
|
|
# CONFIG_NXCONSOLE_MXCHARS
|
|
# NxConsole needs to remember every character written to the console so
|
|
# that it can redraw the window. This setting determines the size of some
|
|
# internal memory allocations used to hold the character data. Default: 128.
|
|
# CONFIG_NXCONSOLE_CACHESIZE
|
|
# NxConsole supports caching of rendered fonts. This font caching is required
|
|
# for two reasons: (1) First, it improves text performance, but more
|
|
# importantly (2) it preserves the font memory. Since the NX server runs on
|
|
# a separate server thread, it requires that the rendered font memory persist
|
|
# until the server has a chance to render the font. (NOTE: There is still
|
|
# inherently a race condition in this!). Unfortunately, the font cache would
|
|
# be quite large if all fonts were saved. The CONFIG_NXCONSOLE_CACHESIZE setting
|
|
# will control the size of the font cache (in number of glyphs). Only that
|
|
# number of the most recently used glyphs will be retained. Default: 16.
|
|
# CONFIG_NXCONSOLE_LINESEPARATION
|
|
# This the space (in rows) between each row of test. Default: 2
|
|
# CONFIG_NXCONSOLE_NOWRAP
|
|
# By default, lines will wrap when the test reaches the right hand side
|
|
# of the window. This setting can be defining to change this behavior so
|
|
# that the text is simply truncated until a new line is encountered.
|
|
#
|
|
CONFIG_NXCONSOLE=n
|
|
CONFIG_NXCONSOLE_BPP=16
|
|
CONFIG_NXCONSOLE_MXCHARS=256
|
|
CONFIG_NXCONSOLE_CACHESIZE=32
|
|
# CONFIG_NXCONSOLE_LINESEPARATION
|
|
# CONFIG_NXCONSOLE_NOWRAP
|
|
|
|
#
|
|
# PIC32MX7 MMB LCD Hardware Configuration
|
|
#
|
|
# CONFIG_LCD_MIO283QT2
|
|
# Enables the MIO183QT2 LCD support.
|
|
# CONFIG_LCD_NOGETRUN
|
|
# NX components need to know if it can read from the LCD or not. If reading
|
|
# from the LCD is supported, then NxConsole can do more efficient
|
|
# scrolling. Default: Supported
|
|
# CONFIG_LCD_LANDSCAPE - Define for 320x240 display "landscape"
|
|
# support. Default is this 320x240 "landscape" orientation
|
|
# CONFIG_LCD_RLANDSCAPE - Define for 320x240 display "reverse
|
|
# landscape" support. Default is this 320x240 "landscape"
|
|
# orientation
|
|
# CONFIG_LCD_PORTRAIT - Define for 240x320 display "portrait"
|
|
# orientation support. In this orientation, the PIC32MX7 MMB's
|
|
# LCD ribbon cable is at the bottom of the display. Default is
|
|
# 320x240 "landscape" orientation.
|
|
# CONFIG_LCD_RPORTRAIT - Define for 240x320 display "reverse
|
|
# portrait" orientation support. In this orientation, the
|
|
# PIC32MX7 MMB's LCD ribbon cable is at the top of the display.
|
|
# Default is 320x240 "landscape" orientation.
|
|
#
|
|
CONFIG_LCD_MIO283QT2=n
|
|
CONFIG_LCD_NOGETRUN=n
|
|
CONFIG_LCD_LANDSCAPE=n
|
|
CONFIG_LCD_RLANDSCAPE=n
|
|
CONFIG_LCD_PORTRAIT=n
|
|
CONFIG_LCD_RPORTRAIT=y
|
|
|
|
#
|
|
# PIC32MX7 MMB specific LCD settings
|
|
#
|
|
|
|
#
|
|
# Settings for examples/uip
|
|
#
|
|
CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
|
|
CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
|
CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
|
|
CONFIG_EXAMPLE_UIP_DHCPC=n
|
|
|
|
#
|
|
# Settings for examples/nettest
|
|
#
|
|
# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act
|
|
# as either the client side or server side of the test
|
|
# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the
|
|
# client side simply receives messages forever, allowing
|
|
# measurement of throughput
|
|
# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has
|
|
# no MAC address; one will be assigned
|
|
# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address
|
|
# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address
|
|
# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask
|
|
# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the
|
|
# client side of the test (may be target or host)
|
|
#
|
|
CONFIG_EXAMPLE_NETTEST_SERVER=n
|
|
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
|
|
CONFIG_EXAMPLE_NETTEST_NOMAC=y
|
|
CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
|
|
CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
|
CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
|
|
CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
|
|
|
|
#
|
|
# Settings for examples/ostest
|
|
#
|
|
CONFIG_EXAMPLES_OSTEST_LOOPS=1
|
|
CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
|
|
CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
|
|
|
|
#
|
|
# Settings for apps/nshlib
|
|
#
|
|
# CONFIG_NSH_BUILTIN_APPS - Support external registered,
|
|
# "named" applications that can be executed from the NSH
|
|
# command line (see apps/README.txt for more information).
|
|
# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
|
|
# CONFIG_NSH_STRERROR - Use strerror(errno)
|
|
# CONFIG_NSH_LINELEN - Maximum length of one command line
|
|
# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
|
|
# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
|
|
# CONFIG_NSH_DISABLEBG - Disable background commands
|
|
# CONFIG_NSH_ROMFSETC - Use startup script in /etc
|
|
# CONFIG_NSH_CONSOLE - Use serial console front end
|
|
# CONFIG_NSH_CONDEV - Select the serial device used to support
|
|
# the NSH console. Default: stdin and stdout
|
|
# CONFIG_NSH_TELNET - Use telnetd console front end
|
|
# CONFIG_NSH_ARCHINIT - Platform provides architecture
|
|
# specific initialization (nsh_archinitialize()).
|
|
#
|
|
# If CONFIG_NSH_TELNET is selected:
|
|
# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
|
|
# CONFIG_NSH_DHCPC - Obtain address using DHCP
|
|
# CONFIG_NSH_IPADDR - Provides static IP address
|
|
# CONFIG_NSH_DRIPADDR - Provides static router IP address
|
|
# CONFIG_NSH_NETMASK - Provides static network mask
|
|
# CONFIG_NSH_NOMAC - Use a bogus MAC address
|
|
#
|
|
# If CONFIG_NSH_ROMFSETC is selected:
|
|
# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
|
|
# CONFIG_NSH_INITSCRIPT - Relative path to init script
|
|
# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
|
|
# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
|
|
# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
|
|
# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
|
|
# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
|
|
# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
|
|
#
|
|
CONFIG_NSH_BUILTIN_APPS=y
|
|
CONFIG_NSH_FILEIOSIZE=512
|
|
CONFIG_NSH_STRERROR=n
|
|
CONFIG_NSH_LINELEN=64
|
|
CONFIG_NSH_NESTDEPTH=3
|
|
CONFIG_NSH_DISABLESCRIPT=n
|
|
CONFIG_NSH_DISABLEBG=n
|
|
CONFIG_NSH_ROMFSETC=n
|
|
CONFIG_NSH_CONSOLE=y
|
|
#CONFIG_NSH_CONDEV="/dev/ttyS1"
|
|
CONFIG_NSH_TELNET=n
|
|
CONFIG_NSH_ARCHINIT=y
|
|
CONFIG_NSH_IOBUFFER_SIZE=512
|
|
CONFIG_NSH_DHCPC=n
|
|
CONFIG_NSH_NOMAC=n
|
|
CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
|
|
CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
|
|
CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
|
|
CONFIG_NSH_ROMFSMOUNTPT="/etc"
|
|
CONFIG_NSH_INITSCRIPT="init.d/rcS"
|
|
CONFIG_NSH_ROMFSDEVNO=0
|
|
CONFIG_NSH_ROMFSSECTSIZE=64
|
|
CONFIG_NSH_FATDEVNO=1
|
|
CONFIG_NSH_FATSECTSIZE=512
|
|
CONFIG_NSH_FATNSECTORS=1024
|
|
CONFIG_NSH_FATMOUNTPT=/tmp
|
|
|
|
#
|
|
# Architecture-specific NSH options
|
|
#
|
|
CONFIG_NSH_MMCSDSPIPORTNO=1
|
|
CONFIG_NSH_MMCSDSLOTNO=0
|
|
CONFIG_NSH_MMCSDMINOR=0
|
|
|
|
#
|
|
# I2C tool settings
|
|
#
|
|
# CONFIG_I2CTOOL_BUILTIN - Build the tools as an NSH built-in command
|
|
# CONFIG_I2CTOOL_MINBUS - Smallest bus index supported by the hardware (default 0).
|
|
# CONFIG_I2CTOOL_MAXBUS - Largest bus index supported by the hardware (default 3)
|
|
# CONFIG_I2CTOOL_MINADDR - Minium device address (default: 0x03)
|
|
# CONFIG_I2CTOOL_MAXADDR - Largest device address (default: 0x77)
|
|
# CONFIG_I2CTOOL_MAXREGADDR - Largest register address (default: 0xff)
|
|
# CONFIG_I2CTOOL_DEFFREQ - Default frequency (default: 1000000)
|
|
#
|
|
CONFIG_I2CTOOL_BUILTIN=y
|
|
CONFIG_I2CTOOL_MINBUS=1
|
|
CONFIG_I2CTOOL_MAXBUS=4
|
|
#CONFIG_I2CTOOL_MINADDR
|
|
#CONFIG_I2CTOOL_MAXADDR
|
|
#CONFIG_I2CTOOL_MAXREGADDR
|
|
CONFIG_I2CTOOL_DEFFREQ=100000
|
|
|
|
#
|
|
# Settings for examples/ftpd
|
|
#
|
|
# CONFIG_EXAMPLES_FTPD_PRIO - Priority of the FTP daemon.
|
|
# Default: SCHED_PRIORITY_DEFAULT
|
|
# CONFIG_EXAMPLES_FTPD_STACKSIZE - Stack size allocated for the
|
|
# FTP daemon. Default: 2048
|
|
# CONFIG_EXAMPLES_FTPD_NONETINIT - Define to suppress configuration of the
|
|
# network by apps/examples/ftpd. You would need to suppress network
|
|
# configuration if the network is configuration prior to running the
|
|
# example.
|
|
#
|
|
# NSH always initializes the network so if CONFIG_NSH_BUILTIN_APPS is
|
|
# defined, so is CONFIG_EXAMPLES_FTPD_NONETINIT (se it does not explicitly
|
|
# need to be defined in that case):
|
|
#
|
|
# CONFIG_NSH_BUILTIN_APPS - Build the FTPD daemon example test as an
|
|
# NSH built-in function. By default the FTPD daemon will be built
|
|
# as a standalone application.
|
|
#
|
|
# If CONFIG_EXAMPLES_FTPD_NONETINIT is not defined, then the following may
|
|
# be specified to customized the network configuration:
|
|
#
|
|
# CONFIG_EXAMPLE_FTPD_NOMAC - If the hardware has no MAC address of its
|
|
# own, define this =y to provide a bogus address for testing.
|
|
# CONFIG_EXAMPLE_FTPD_IPADDR - The target IP address. Default 10.0.0.2
|
|
# CONFIG_EXAMPLE_FTPD_DRIPADDR - The default router address. Default
|
|
# 10.0.0.1
|
|
# CONFIG_EXAMPLE_FTPD_NETMASK - The network mask. Default: 255.255.255.0
|
|
|
|
#
|
|
# Settings for examples/usbserial
|
|
#
|
|
# CONFIG_EXAMPLES_USBSERIAL_INONLY
|
|
# Only verify IN (device-to-host) data transfers. Default: both
|
|
# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
|
|
# Only verify OUT (host-to-device) data transfers. Default: both
|
|
# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
|
|
# Send only small, single packet messages. Default: Send large and small.
|
|
# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
|
|
# Send only large, multi-packet messages. Default: Send large and small.
|
|
#
|
|
CONFIG_EXAMPLES_USBSERIAL_INONLY=n
|
|
CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
|
|
CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
|
|
CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
|
|
|
|
CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
|
|
CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
|
|
CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
|
|
CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
|
|
CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
|
|
|
|
#
|
|
# Settings for examples/usbstorage
|
|
#
|
|
# CONFIG_EXAMPLES_USBMSC_BUILTIN
|
|
# Build the USBMSC storage example as an NSH built-in application.
|
|
# CONFIG_EXAMPLES_USBMSC_NLUNS
|
|
# Defines the number of logical units (LUNs) exported by the USB storage
|
|
# driver. Each LUN corresponds to one exported block driver (or partition
|
|
# of a block driver). May be 1, 2, or 3. Default is 1.
|
|
# CONFIG_EXAMPLES_USBMSC_DEVMINOR1
|
|
# The minor device number of the block driver for the first LUN. For
|
|
# example, N in /dev/mmcsdN. Used for registering the block driver. Default
|
|
# is zero.
|
|
# CONFIG_EXAMPLES_USBMSC_DEVPATH1
|
|
# The full path to the registered block driver. Default is "/dev/mmcsd0"
|
|
# CONFIG_EXAMPLES_USBMSC_DEVMINOR2 and CONFIG_EXAMPLES_USBMSC_DEVPATH2
|
|
# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS
|
|
# is 2 or 3. No defaults.
|
|
# CONFIG_EXAMPLES_USBMSC_DEVMINOR3 and CONFIG_EXAMPLES_USBMSC_DEVPATH3
|
|
# Similar parameters that would have to be provided if CONFIG_EXAMPLES_USBMSC_NLUNS
|
|
# is 3. No defaults.
|
|
#
|
|
# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB), then
|
|
# the example code will also manage the USB trace output. The amount of trace output
|
|
# can be controlled using:
|
|
#
|
|
# CONFIG_EXAMPLES_USBMSC_TRACEINIT
|
|
# Show initialization events
|
|
# CONFIG_EXAMPLES_USBMSC_TRACECLASS
|
|
# Show class driver events
|
|
# CONFIG_EXAMPLES_USBMSC_TRACETRANSFERS
|
|
# Show data transfer events
|
|
# CONFIG_EXAMPLES_USBMSC_TRACECONTROLLER
|
|
# Show controller events
|
|
# CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS
|
|
# Show interrupt-related events.
|
|
#
|
|
CONFIG_EXAMPLES_USBMSC_BUILTIN=y
|
|
CONFIG_EXAMPLES_USBMSC_NLUNS=1
|
|
CONFIG_EXAMPLES_USBMSC_DEVMINOR1=0
|
|
CONFIG_EXAMPLES_USBMSC_DEVPATH1="/dev/mmcsd0"
|
|
CONFIG_EXAMPLES_USBMSC_TRACEINIT=n
|
|
CONFIG_EXAMPLES_USBMSC_TRACECLASS=n
|
|
CONFIG_EXAMPLES_USBMSC_TRACETRANSFERS=n
|
|
CONFIG_EXAMPLES_USBMSC_TRACECONTROLLER=n
|
|
CONFIG_EXAMPLES_USBMSC_TRACEINTERRUPTS=n
|
|
|
|
#
|
|
# Settings for examples/usbterm
|
|
#
|
|
# CONFIG_EXAMPLES_USBTERM_BUILTIN - Build the usbterm example as an NSH
|
|
# built-in command. NOTE: This is not fully functional as of this
|
|
# writing.. It should work, but there is no mechanism in place yet
|
|
# to exit the USB terminal program and return to NSH.
|
|
# CONFIG_EXAMPLES_USBTERM_DEVINIT - If defined, then the example will
|
|
# call a user provided function as part of its initialization:
|
|
# int usbterm_devinit(void);
|
|
# And another user provided function at termination:
|
|
# void usbterm_devuninit(void);
|
|
# CONFIG_EXAMPLES_USBTERM_BUFLEN - The size of the input and output
|
|
# buffers used for receiving data. Default 256 bytes.
|
|
#
|
|
# If CONFIG_USBDEV_TRACE is enabled (or CONFIG_DEBUG and CONFIG_DEBUG_USB, or
|
|
# CONFIG_USBDEV_TRACE), then the example code will also manage the USB trace
|
|
# output. The amount of trace output can be controlled using:
|
|
#
|
|
# CONFIG_EXAMPLES_USBTERM_TRACEINIT
|
|
# Show initialization events
|
|
# CONFIG_EXAMPLES_USBTERM_TRACECLASS
|
|
# Show class driver events
|
|
# CONFIG_EXAMPLES_USBTERM_TRACETRANSFERS
|
|
# Show data transfer events
|
|
# CONFIG_EXAMPLES_USBTERM_TRACECONTROLLER
|
|
# Show controller events
|
|
# CONFIG_EXAMPLES_USBTERM_TRACEINTERRUPTS
|
|
# Show interrupt-related events.
|
|
#
|
|
CONFIG_EXAMPLES_USBTERM_BUILTIN=y
|
|
CONFIG_EXAMPLES_USBTERM_DEVINIT=y
|
|
#CONFIG_EXAMPLES_USBTERM_BUFLEN
|
|
CONFIG_EXAMPLES_USBTERM_TRACEINIT=n
|
|
CONFIG_EXAMPLES_USBTERM_TRACECLASS=n
|
|
CONFIG_EXAMPLES_USBTERM_TRACETRANSFERS=n
|
|
CONFIG_EXAMPLES_USBTERM_TRACECONTROLLER=n
|
|
CONFIG_EXAMPLES_USBTERM_TRACEINTERRUPTS=n
|
|
|
|
#
|
|
# Settings for examples/cdcacm
|
|
#
|
|
# Configuration prequisites:
|
|
#
|
|
# CONFIG_USBDEV=y : USB device support must be enabled
|
|
# CONFIG_CDCACM=y : The CDC/ACM driver must be built
|
|
# CONFIG_NSH_BUILTIN_APPS : NSH built-in application support must be enabled
|
|
#
|
|
# Configuration options specific to this example:
|
|
#
|
|
# CONFIG_EXAMPLES_CDCACM_DEVMINOR
|
|
# The minor number of the CDC/ACM device.
|
|
# CONFIG_EXAMPLES_CDCACM_TRACEINIT
|
|
# Show initialization events
|
|
# CONFIG_EXAMPLES_CDCACM_TRACECLASS
|
|
# Show class driver events
|
|
# CONFIG_EXAMPLES_CDCACM_TRACETRANSFERS
|
|
# Show data transfer events
|
|
# CONFIG_EXAMPLES_CDCACM_TRACECONTROLLER
|
|
# Show controller events
|
|
# CONFIG_EXAMPLES_CDCACM_TRACEINTERRUPTS
|
|
# Show interrupt-related events.
|
|
#
|
|
CONFIG_EXAMPLES_CDCACM_DEVMINOR=0
|
|
CONFIG_EXAMPLES_CDCACM_TRACEINIT=n
|
|
CONFIG_EXAMPLES_CDCACM_TRACECLASS=n
|
|
CONFIG_EXAMPLES_CDCACM_TRACETRANSFERS=n
|
|
CONFIG_EXAMPLES_CDCACM_TRACECONTROLLER=n
|
|
CONFIG_EXAMPLES_CDCACM_TRACEINTERRUPTS=n
|
|
|
|
#
|
|
# Stack and heap information
|
|
#
|
|
# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
|
|
# operation from FLASH but must copy initialized .data sections to RAM.
|
|
# (should also be =n for the PIC32MX which always runs from flash)
|
|
# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH
|
|
# but copy themselves entirely into RAM for better performance.
|
|
# CONFIG_CUSTOM_STACK - The up_ implementation will handle
|
|
# all stack operations outside of the nuttx model.
|
|
# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
|
|
# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
|
|
# This is the thread that (1) performs the inital boot of the system up
|
|
# to the point where user_start() is spawned, and (2) there after is the
|
|
# IDLE thread that executes only when there is no other thread ready to
|
|
# run.
|
|
# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
|
|
# for the main user thread that begins at the user_start() entry point.
|
|
# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
|
|
# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
|
|
# CONFIG_HEAP_BASE - The beginning of the heap
|
|
# CONFIG_HEAP_SIZE - The size of the heap
|
|
#
|
|
CONFIG_BOOT_RUNFROMFLASH=n
|
|
CONFIG_BOOT_COPYTORAM=n
|
|
CONFIG_CUSTOM_STACK=n
|
|
#CONFIG_STACK_POINTER
|
|
CONFIG_IDLETHREAD_STACKSIZE=2048
|
|
CONFIG_USERMAIN_STACKSIZE=2048
|
|
CONFIG_PTHREAD_STACK_MIN=256
|
|
CONFIG_PTHREAD_STACK_DEFAULT=2048
|
|
CONFIG_HEAP_BASE=
|
|
CONFIG_HEAP_SIZE=
|