86 lines
2.4 KiB
ReStructuredText
86 lines
2.4 KiB
ReStructuredText
==================
|
|
ST Nucleo U5A5ZJ-Q
|
|
==================
|
|
|
|
This page file discusses the port of NuttX to the STMicroelectronics
|
|
NUCLEO-U5A5ZJ-Q board. That board features the STM32U5A5ZJT6Q MCU with 4MiB
|
|
of Flash and 2500KiB of SRAM.
|
|
|
|
Status
|
|
======
|
|
|
|
2023-07-16: Initial port - works all ram memory and i2c(not extensively tested)
|
|
The i2c driver is based on stm32l4 one
|
|
|
|
Clock Source
|
|
============
|
|
|
|
Only the low speed external (LSE) 32.768kHz crystal (X2) is installed in
|
|
default configurations.
|
|
|
|
========= ====
|
|
FUNC GPIO
|
|
========= ====
|
|
OSC32_IN PC14
|
|
OSC32_OUT PC15
|
|
========= ====
|
|
|
|
Serial Consoles
|
|
===============
|
|
|
|
Virtual COM Port on USART1
|
|
--------------------------
|
|
|
|
Default board is configured to use USART1 as console. USART1 is connected
|
|
to the ST-LINKV3E Virtual COM port as well as made available on connector
|
|
CN10 (need some rework on PCB).
|
|
|
|
Pins and Connectors:
|
|
|
|
==== ==== ======= ========
|
|
FUNC GPIO Pin NAME
|
|
==== ==== ======= ========
|
|
TXD: PA9 CN10 14 T.VCP_TX
|
|
RXD: PA10 CN9 13 T.VCP_RX
|
|
==== ==== ======= ========
|
|
|
|
Configurations
|
|
==============
|
|
|
|
Information Common to All Configurations
|
|
----------------------------------------
|
|
|
|
There is only one configuration which can be selected as follow::
|
|
|
|
tools/configure.sh nucleo-u5a5zj-q:nsh
|
|
|
|
Before building, make sure the PATH environment variable includes the
|
|
correct path to the directory than holds your toolchain binaries.
|
|
|
|
And then build NuttX by simply typing the following. At the conclusion of
|
|
the make, the nuttx binary will reside in an ELF file called, simply, nuttx.::
|
|
|
|
make menuconfig
|
|
make
|
|
|
|
The <subdir> that is provided above as an argument to the tools/configure.sh
|
|
must be is one of the following.
|
|
|
|
NOTES:
|
|
|
|
1. These configurations use the mconf-based configuration tool. To
|
|
change any of these configurations using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
2. All of these configurations are set up to build under Linux using the
|
|
"GNU Tools for ARM Embedded Processors" that is maintained by ARM
|
|
(unless stated otherwise in the description of the configuration).
|
|
|
|
https://developer.arm.com/open-source/gnu-toolchain/gnu-rm
|
|
|