2023-08-24 15:00:13 +02:00
|
|
|
==============
|
|
|
|
|
ET-STM32 Stamp
|
|
|
|
|
==============
|
|
|
|
|
|
2023-08-24 13:50:32 +02:00
|
|
|
This page discusses issues/thoughts unique to NuttX configuration(s) for the
|
2023-08-24 15:00:13 +02:00
|
|
|
ET-STM32 Stamp board from Futurlec (https://www.futurlec.com/ET-STM32_Stamp.shtml).
|
|
|
|
|
|
2023-08-24 13:50:32 +02:00
|
|
|
- Microprocessor: 32-bit ARM Cortex M3 at 72MHz STM32F103RET6
|
|
|
|
|
- Memory: 512 KB Flash and 64 KB SRAM
|
|
|
|
|
- I/O Pins Out: 48
|
|
|
|
|
- ADCs: 16 (at 12-bit resolution)
|
|
|
|
|
- DACs: 2 (at 12-bit resolution)
|
2023-10-28 21:40:30 +02:00
|
|
|
- Peripherals: RTC, 4 timers, 2 I2Cs, 3 SPI ports, 1 on-board UART (up to 5 channels)
|
2023-08-24 13:50:32 +02:00
|
|
|
- Other: Sleep, stop, and standby modes; serial wire debug and JTAG interfaces
|
2023-08-24 15:00:13 +02:00
|
|
|
|
|
|
|
|
Please see link below for board specific details:
|
|
|
|
|
|
|
|
|
|
https://www.futurlec.com/ET-STM32_Stamp_Technical.shtml
|
|
|
|
|
|
|
|
|
|
This configuration supports the ET-STM32 Stamp module.
|
|
|
|
|
|
|
|
|
|
Development Environment
|
|
|
|
|
=======================
|
|
|
|
|
|
|
|
|
|
Either Linux (recommended), Mac or Cygwin on Windows can be used for the development
|
|
|
|
|
environment. The source has been built only using the GNU (Cortex M) toolchain.
|
|
|
|
|
Other toolchains will likely cause problems.
|
|
|
|
|
|
|
|
|
|
WSL (Windows Subsystem for Linux) was used to develop, compile and test the NuttX
|
|
|
|
|
build for the ET-STM32 Stamp platform.
|
|
|
|
|
|
|
|
|
|
Flashing/Programming
|
|
|
|
|
====================
|
|
|
|
|
|
|
|
|
|
Prerequisites:
|
|
|
|
|
|
|
|
|
|
1. The ET-STM32 Stamp module from Futurlec.
|
|
|
|
|
|
|
|
|
|
2. An RS232 connection cable such as the one in this link: (Part code: RS232CONN):
|
|
|
|
|
https://www.futurlec.com/DevBoardAccessories.shtml
|
|
|
|
|
|
|
|
|
|
It has a 4-pin connection header on one end and an RS-232 (DB9) female connector on
|
|
|
|
|
the other. The 4-pin connector can be directly plugged onto the Stamp module.
|
|
|
|
|
|
|
|
|
|
3. An RS232 to USB converter cable. Ensure that a suitable driver is installed for
|
|
|
|
|
the converter cable. When the cable is plugged in (for example), my PC lists the
|
|
|
|
|
assigned port with this name: "USB-SERIAL CH340 (COM2)".
|
|
|
|
|
|
|
|
|
|
Assuming Windows 10, navigate to: This PC -> Manage -> Device Manager -> Ports.
|
|
|
|
|
|
|
|
|
|
4. ST's Flash loader demonstrator tool. You can download it from here:
|
|
|
|
|
https://www.st.com/en/development-tools/flasher-stm32.html
|
|
|
|
|
|
|
|
|
|
To install the NuttX firmware (nuttx.bin) on the ET-STM32 Stamp:
|
|
|
|
|
|
|
|
|
|
1. First, power the Stamp module with a 3.3 VDC power supply. I made my own
|
|
|
|
|
Stamp module fixture using a 3.3 VDC switching regulator, a prototype PCB card
|
|
|
|
|
and some solder.
|
|
|
|
|
|
|
|
|
|
2. Insert the RS232CONN into the 4-pin on-board header. The other end should be
|
|
|
|
|
connected to the USB port of the PC using the RS232-USB converter.
|
|
|
|
|
|
|
|
|
|
3. Set the BOOT1 jumper on your board to the ISP position.
|
|
|
|
|
|
|
|
|
|
4. Press the BOOT0 switch. The green "BOOT0=1" LED should light up.
|
|
|
|
|
|
|
|
|
|
5. Reset the board by pressing on the RESET button.
|
|
|
|
|
|
|
|
|
|
6. Using the ST Flash loader demonstrator to download the NuttX binary image.
|
|
|
|
|
|
|
|
|
|
7. Wait until programming is completed and press "Finish". Toggle the
|
|
|
|
|
BOOT0 switch again. Reset the board.
|
|
|
|
|
|
|
|
|
|
You will now be presented with the NuttShell (NSH). Enjoy.
|
|
|
|
|
|
|
|
|
|
Configurations
|
|
|
|
|
==============
|
|
|
|
|
|
|
|
|
|
Information Common to All Configurations
|
|
|
|
|
----------------------------------------
|
|
|
|
|
|
|
|
|
|
The ET-STM32 Stamp configuration is maintained in a sub-directory and can be
|
|
|
|
|
selected as follow::
|
|
|
|
|
|
|
|
|
|
tools/configure.sh et-stm32-stamp:<subdir>
|
|
|
|
|
|
|
|
|
|
Before building, make sure the PATH environment variable includes the
|
|
|
|
|
correct path to the directory than holds your toolchain binaries.
|
|
|
|
|
|
|
|
|
|
And then build NuttX by simply typing the following. At the conclusion of
|
|
|
|
|
the make, the nuttx binary will reside in an ELF file called, simply, nuttx.::
|
|
|
|
|
|
|
|
|
|
make
|
|
|
|
|
|
|
|
|
|
The <subdir> that is provided above as an argument to the tools/configure.sh
|
|
|
|
|
must be in one of the following.
|
|
|
|
|
|
|
|
|
|
NOTES:
|
|
|
|
|
|
|
|
|
|
1. These configurations use the mconf-based configuration tool. To
|
|
|
|
|
change any of these configurations using that tool, you should:
|
|
|
|
|
|
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
|
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
|
|
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
|
|
|
reconfiguration process.
|
|
|
|
|
|
|
|
|
|
Configuration Sub-directories
|
|
|
|
|
-----------------------------
|
|
|
|
|
|
|
|
|
|
nsh:
|
|
|
|
|
----
|
|
|
|
|
|
|
|
|
|
This configuration directory provide the basic NuttShell (NSH).
|
|
|
|
|
A serial console is provided on USART1.
|
