W25QxxxJV NOR memories are backward compatible with older Winbond´s
generations and thus can also be supported here. This essentially brings
the support for generic SPI to W25QxxxJV memories as w25qxxxjv.c file only
supports QSPI communication.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
1.support to use dd commond to burn romfs image to nand flash
2.support bare-write nand flash device without file system
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
1. Update all CMakeLists.txt to adapt to new layout
2. Fix cmake build break
3. Update all new file license
4. Fully compatible with current compilation environment(use configure.sh or cmake as you choose)
------------------
How to test
From within nuttx/. Configure:
cmake -B build -DBOARD_CONFIG=sim/nsh -GNinja
cmake -B build -DBOARD_CONFIG=sim:nsh -GNinja
cmake -B build -DBOARD_CONFIG=sabre-6quad/smp -GNinja
cmake -B build -DBOARD_CONFIG=lm3s6965-ek/qemu-flat -GNinja
(or full path in custom board) :
cmake -B build -DBOARD_CONFIG=$PWD/boards/sim/sim/sim/configs/nsh -GNinja
This uses ninja generator (install with sudo apt install ninja-build). To build:
$ cmake --build build
menuconfig:
$ cmake --build build -t menuconfig
--------------------------
2. cmake/build: reformat the cmake style by cmake-format
https://github.com/cheshirekow/cmake_format
$ pip install cmakelang
$ for i in `find -name CMakeLists.txt`;do cmake-format $i -o $i;done
$ for i in `find -name *\.cmake`;do cmake-format $i -o $i;done
Co-authored-by: Matias N <matias@protobits.dev>
Signed-off-by: chao an <anchao@xiaomi.com>
Directly return -ENOTTY in rpmsgxxx_ioctl() when the command is
not supported to avoid fdsan command FIOC_SETTAG and FIOC_GETTAG
pass to the rpmsg dev/mtd/blk server with CONFIG_FDSAN enabled.
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
1 Gbit W25Q01JV flash uses two 512 Mbit dies. This requires specific
operations in the driver in order to support the entire 1 Gbit region.
This commit adds dual die support for W25Q01JV flash.
Generally the driver has to switch active dies when die specific read from
status register is required (therefore before read, write, erase and when
checking if write status register was successful).
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
W25QXXXJV_WRITE_STATUS_2 register uses just first byte therefore all
operations has to be done in priv->cmdbuf[0]. Previous priv->cmdbuf[1]
caused QuadSPI mode not being enabled.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
follow how Linux report the correction information from ecc:
http://www.infradead.org/pipermail/linux-mtd/2012-March/040305.html
since this information is very useful to file system(e.g. yaffs, ubi/buifs)
which is specially designed for nand flash.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Since not all nand devices follow ONFI spec, nand_raw_initialize could be used to skip ONFI special action
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Current driver supports MTDIOC_BULKERASE ioctl that erases the entire
device. The added ioctl MTDIOC_ERASESECTORS adds possibility to erase
just sectors defined by the user.
This is similar to MEMERASE call in Linux kernel.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
since mmap may exist in block_operations, but truncate may not,
moving mmap beforee truncate could make three struct more compatible
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
- Add mmap into file_operations and remove it from ioctl definitions.
- Add mm_map structure definitions to support future unmapping
- Modify all drivers to initialize the operations struct accordingly
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- Add truncate into file_operations
- Move truncate to be common for mountpt_operations and file_operations
- Modify all drivers to initialize the operations struct accordingly
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
GG25Q devices have the 4 byte read mode in bit 0 not bit 3 of the status register. This changes allows for both depending on the JEDEC DEVICE ID that is read back.
since we can query this value by MTDIOC_ERASESTATE after:
commit 30cb497fe1
Author: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Date: Tue Jul 13 19:33:12 2021 -0300
mtd: Add MTDIOC_ERASESTATE command for retrieving erase state value
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Certain variants of the W25QxxxJV Quad SPI NOR flash ICs have the Quad
SPI mode disabled after reset. As the w25qxxxjv driver is operating the
device in Quad SPI mode, make sure it gets enabled if required during
device initialization.
Signed-off-by: Michael Jung <michael.jung@secore.ly>
If CONFIG_SMARTFS_MULTI_ROOT_DIRS is enabled and dev->partname is not empty,
dev->rwbuffer is an uninitialized variable and register_blockdriver is called.
When device not support byte read or readlen less than
device block size, will use `dev->buffer` as dst address.
`CFGDIOC_FIRSTCONFIG` and `CFGDIOC_NEXTCONFIG` should also
malloc buffer before call `mtdconfig_readbytes`.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
- fix memory leak during RAM MTD initialization
- fix calculations for FILE MTD device with customized
block and erase sizes
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
