Summary:
- I thought this cs is needed to avoid data corruption
- For example, while executing uart_xmitchar() in the interrupt
handler on CPU0, an application running on CPU1 can call
uart_putxmitchar() via write()->uart_write().
- In this case, taking xmit.sem in uart_write() will wait for CPU0
to finish uart_xmitchar() because CPU0 has already taken a cs
in uart_xmitchar() then nxsem_wait() on CPU0 takes a new cs
inside (and release the cs when returning but it's OK)
- Then uart_write() on CPU1 disables UART TX, so uart_xmitchar()
on CPU0 will not be called while executing uart_write() on CPU1.
- So this critical section in uart_putxmitchar() can be removed.
Impact:
- None
Testing:
- Tested with spresense:wifi_smp, esp32-devkitc:smp
Reported-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
This is addressing an issue where Rx interrupts were not restored for
cdcacm after the buffer had been filled (in a burst).
The Rx interrupts were only restored after the watchdog timeout of 200ms
fired.
This happened because CONFIG_SERIAL_RXDMA was set, however, for the
cdcacm driver this does not actually matter as it is relying on
uart_enablerxint to be called via the ops table.
This patch makes sure that uart_enablerxint and uart_disablerxint are
always called, independent of CONFIG_SERIAL_RXDMA, relying on the ops
table to be correct for the case where it should be only a no-op.
Re-check RX queue status after uart_enablerxint() and before blocking
the reading task on the receive semaphore. cdcacm (and maybe other UART
drivers) can push buffered data into the receive queue during
uart_enablerxint(), leading to a blocked task while data is already
available.
Signed-off-by: Tido Klaassen <tido@4gh.eu>
Follow the POSIX description.
SIGTSTP should be sent when the Ctrl-Z characters is encountered, not SIGSTP.
Testing:
Built with hifive1-revb:nsh (CONFIG_SERIAL_TERMIOS=y, CONFIG_SIG_DEFAULT=y and CONFIG_TTY_SIGTSTP=y)
There is a good case on sim platform:
When we input some cmd and click enter key to start application in terminal,
this context will change to application from IDLE loop. Althrough entey key '\r'
has been received to recv buffer and complete post semaphore of reader, but
pollnotify may not be called because context change. So when application run
poll function, because no events happend and poll enter wait, context will
again change to IDLE loop, this pollnotify of IDLE loop will run to send poll
events, poll function of applicaton will wake up. It's wrong!
Change-Id: I812a889f2e90781a9c3cb4b0251cccc4d32bebd1
Signed-off-by: dongjiuzhu <dongjiuzhu1@xiaomi.com>
boards/z80/ez80/z20x/configs/w25boot/defconfig: Increase size of serial Tx buffer.
boards/z80/ez80/z20x/src/w25_main.c: Add some fflush() in necessary places. Greatly improves the usability of the UI.
boards/z80/ez80/z20x/README.txt: Trival update to README
drivers/serial/serial.c and tcdrain.c: Correct some typos.
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
drivers: serial: Fix data corruption when outputting data in SMP mode
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
sched/ audio/ crypto/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
Documentation/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
fs/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
graphics/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
net/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
drivers/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
include/, syscall/, wireless/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
configs/: Remove all references to CONFIG_DISABLE_POLL. Standard POSIX poll can no longer be disabled.
libs/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
syscall/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
wireless/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
Documentation/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
include/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
drivers/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
sched/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
configs: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/xtensa: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/z80: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/x86: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/renesas and arch/risc-v: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/or1k: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/misoc: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/mips: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/avr: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/arm: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
