Bug description:
CONFIG_SMP=y
Suppose we have 2 cores in SMP, here is the ps return:
PID GROUP CPU PRI POLICY TYPE NPX STATE STACK USED FILLED COMMAND
0 0 0 0 FIFO Kthread N-- Assigned 004076 000748 18.3% CPU0 IDLE
1 0 1 0 FIFO Kthread N-- Running 004096 000540 13.1% CPU1 IDLE
nsh> kill -4 0
or:
nsh> kill -4 1
system blocked.
Reason:
In func xx_sigdeliver() restore stage, when saved_irqcount == 0, that means
rtcb NOT in critical_section before switch to xx_sigdeliver(), then we need
reset the critical_section state before swith back.
Fix:
Add condition to cover saved_irqcount == 0.
Change-Id: I4af7f95e47f6d78a4094c3757d39b01ac9d533b3
Signed-off-by: ligd <liguiding1@xiaomi.com>
This Knob will cycle through the values from
low to high. To avoid damaging the crystal.
We want to use the lowest setting that gets
the OSC running. See app note AN2867
This Knob will cycle through the correct*
values from low to high. To avoid damaging
the crystal. We want to use the lowest setting
that gets the OSC running. See app note AN2867
*It will take into account the rev of the silicon
and use the correct code points to achive the drive
strength. See Eratta ES0392 Rev 7 2.2.14 LSE oscillator
driving capability selection bits are swapped.
With TrustZone support in armv8-m the bit-fields in EXC_RETURN have been
extended. Bit 6 ('S') now specifies whether the interrupted program was
running in the Non-Secure (S=0) or Secure (S=1) security state.
Furthermore, Bit 0 ('ES' - Exception Secure) specifies the
security state athe exception is taken to (0: Non-Secure, 1: Secure).
When NuttX is run together with TrustedFirmware-M as the application in
the non-secure world both the S and the ES bits have to be set to '0'.
For armv8-m those are also the correct values if TrustZone is not
implemented on the respective MCU or if it is disabled.
Signed-off-by: Michael Jung <mijung@gmx.net>
Summary:
- This commit applies armv7-m signal handling logic
Impact:
- armv6-m signal handling
Testing:
- Tested with ostest with the following configs
- raspberrypi-pico:nsh, raspberrypi-pico:smp
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- This commit adds 'select ARM_HAVE_WFE_SEV' to ARCH_CHIP_RP2040
- Now NuttX spinlock uses WFE/SEV to reduce power consumption
- Also, modify a comment on rp2040
Impact:
- rp2040 only
Testing:
- Tested with raspberrypi-pico:smp
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- In the previous implementation, the build system stops if
PICO_SDK_PATH is not set.
- However, this behavior is not good for CI. Because the path
is only used to generate a flash image.
- This commit fixes this issue
Impact:
- rp2040 only
Testing:
- Tested with and without PICO_SDK_PATH
This change reflects that the geometry isn't related to the largest
allocatable unit on the platform.
Calls to read and write block devices are also affected and have
been updated.
Check if all messages were transferred, if not, return -ENXIO.
This is particularly useful when the slave returns an unexpected NAK,
the application code should catch the error to avoid failing silently.
Summary:
- This commit introduces driver-specific spinlock in cxd56_serial.c
to improve performance
Impact:
- SMP only
Testing:
- Tested with spresense:wifi and spresense:wifi_smp
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- This commit changes spinlock APIs (spin_lock_irqsave/spin_unlock_irqrestore)
- In the previous implementation, the global spinlock (i.e. g_irq_spin) was used.
- This commit allows to use caller specific spinlock but also supports to use
g_irq_spin for backword compatibility (In this case, NULL must be specified)
Impact:
- None
Testing:
- Tested with the following configurations
- spresnse:wifi, spresense:wifi_smp
- esp32-devkitc:smp (QEMU), sabre6-quad:smp (QEMU)
- maxi-bit:smp (QEMU), sim:smp
- stm32f4discovery:wifi
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- This commit fixes style warnings under max32660
- Also fix compile errors in max32660_gpio.c with CONFIG_DEBUG_GPIO_INFO=y
Impact:
- None
Testing:
- Built with max32660-evsys:nsh
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- In the previous imxrt_enet.c, imxrt_enet.c assumed that
CONFIG_NET_ETH_PKTSIZE includes the ethernet CRC (4bytes)
- However, most of the driver implementation explicitly
add CONFIG_NET_GUARDSIZE for the CRC to the internal buffer
- This commit conforms to such rules
Imapct:
- No impact
Testing:
- Tested with iperf with imxrt1060-evk
- NOTE: need to add the following configs
+CONFIG_EXAMPLES_IPERF=y
+CONFIG_EXAMPLES_IPERFTEST_DEVNAME="eth0"
+CONFIG_IOB_NBUFFERS=128
+CONFIG_NET_ETH_PKTSIZE=1514
+CONFIG_NET_GUARDSIZE=4
+CONFIG_RR_INTERVAL=200
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Port C was not working because the GPIO pin count was
wrong. The 48 pin packages has 34 GPIO (Not counting PH0 & PH1)
It is GPIOA GPIO B (sans PB11) and GPIOC PC13-PC15
The calls via RTC API weren't fast enough for the edge case
of minimum counter value, resulting in the timer never
expiring as the counter had already passed the compare value.
This now uses direct register access functions and also
gets the latest counter value in edge case.
The MCAN driver private structure has been renamed to struct sam_mcan_s,
but some functions reference sam_can_s. There are missing defines
of return variable in some functions.
Signed-off-by: Pavel Pisa <ppisa@pikron.com>
Summary:
- This commit fixes a compile error in imx_enet.c
with CONFIG_DEBUG_ASSERTIONS=y
Impact:
- None
Testing:
- Tested with sabre-6quad:netnsh with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
