ieee802154: Simplifies notify() and rxframe() calls to a single notify() call. dataind's and all other "notifs" are now "primitives" which aligns with standard terminology
* mac802154: Adds missing breaks from case statement
* sixlowpan: Fixes bad logic where ACK is not requested if address is not a broadcast
* ieee802154: Simplification of "notifs" and "datainds" to generic primitives passed via a single notify call to the layer above the MAC
* Directories.mk should reference CONFIG_WIRELESS instead of CONFIG_DRIVERS_WIRELESS
* xbee_netdev: Network must be locked when calling sixlowpan_input
* sixlowpan: Reassembly buffer can't be freed if provided by radio driver
* sixlowpan: Don't free IOB if there is an error processing it as the MAC will try to pass it along to another receiver
* ieee802154: Adds basic logging to ieee802154_primitive.c
* Minor fixes after rebase
* xbee: Adds AT query timeout to retry if XBee doesn't respond to request
* same70-xplained: Adds Xbee support. Makes mikroBus slot Kconfig 'choice'
* mac802154: Removes unused function declaration
* drivers/mrf24j40: Fixes compilation error using . operator rather than -> operator
* mac802154_device: Changes a few mac802154_primtive_free's to ieee802154_primitive_free() and changes notif to primitive in a couple places.
* mac802154: Adds promiscous mode logic to bypass parsing of incoming frames. MAC char device also checks for promiscous mode and passes whole frames including header and FCS to the application if promiscous mode is enabled.
* sixlowpan: Fixes logic to correctly check if packet is large enough to include header. This would cause packets to be considered too small when they are sufficiently sized.
* sixlowpan: Fixes forwarding logic to use forwarding device rather than received device to look up destination link layer address
* net/ipforward: Fixes typo that caused build error when IP forwarding was enabled with CONFIG_NET_ICMPv6_NEIGHBOR enabled as well.
* configs/same70-xplained: Simple spelling fix
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Replace all calls to sigqueue() in the OS proper with calls to nxsig_queue() to avoid accessing the errno variable.
sched/signal: Add nxsig_queue() which is functionally equivalent to sigqueue() except that it does not modify the errno variable.
This commit backs out most of commit b4747286b1. That change was added because sem_wait() would sometimes cause cancellation points inappropriated. But with these recent changes, nxsem_wait() is used instead and it is not a cancellation point.
In the OS, all calls to sem_wait() changed to nxsem_wait(). nxsem_wait() does not return errors via errno so each place where nxsem_wait() is now called must not examine the errno variable.
In all OS functions (not libraries), change sem_wait() to nxsem_wait(). This will prevent the OS from creating bogus cancellation points and from modifying the per-task errno variable.
sched/semaphore: Add the function nxsem_wait(). This is a new internal OS interface. It is functionally equivalent to sem_wait() except that (1) it is not a cancellation point, and (2) it does not set the per-thread errno value on return.
sched/semaphore: Add nxsem_post() which is identical to sem_post() except that it never modifies the errno variable. Changed all references to sem_post in the OS to nxsem_post().
sched/semaphore: Add nxsem_destroy() which is identical to sem_destroy() except that it never modifies the errno variable. Changed all references to sem_destroy() in the OS to nxsem_destroy().
libc/semaphore and sched/semaphore: Add nxsem_getprotocol() and nxsem_setprotocola which are identical to sem_getprotocol() and set_setprotocol() except that they never modifies the errno variable. Changed all references to sem_setprotocol in the OS to nxsem_setprotocol(). sem_getprotocol() was not used in the OS
libc/semaphore: Add nxsem_getvalue() which is identical to sem_getvalue() except that it never modifies the errno variable. Changed all references to sem_getvalue in the OS to nxsem_getvalue().
sched/semaphore: Rename all internal private functions from sem_xyz to nxsem_xyz. The sem_ prefix is (will be) reserved only for the application semaphore interfaces.
libc/semaphore: Add nxsem_init() which is identical to sem_init() except that it never modifies the errno variable. Changed all references to sem_init in the OS to nxsem_init().
sched/semaphore: Rename sem_tickwait() to nxsem_tickwait() so that it is clear this is an internal OS function.
sched/semaphoate: Rename sem_reset() to nxsem_reset() so that it is clear this is an internal OS function.
drivers/xbee: Fixes a few warnings
* drivers/xbee: Fixes a few warnings
* configs/clicker2-stm32: Updates sections about i8sak usage in the README
Approved-by: Gregory Nutt <gnutt@nuttx.org>
drivers/wireless: Adds XBee S2C (802.15.4 firmware) support. XBee driver emulates mac802154 interface
* drivers/wireless/xbee: Adds xbee_netdev. Very similar to mac802154_netdev
* configs/same70-xplained: Starts adding support for XBee radio
* drivers/wireless/ieee802154/xbee: More structuring of XBee driver
* drivers/wireless/ieee802154/xbee: More Xbee work. Starts adding support on Clicker2
* drivers/wireless/ieee802154/xbee: More XBee MAC code
* configs/clicker2-stm32: More work to add XBee radio support
* drivers/wireless/ieee802154/xbee: Most of driver is now structured. No build errors
* configs/clicker2-stm32: Adjustments to XBee click module support
* drivers/xbee: Changes md_ prefix to xd_ prefix for xbeenet_driver_s fields
* drivers/xbee: XBee network device now passes MAC events via IOCTL
* drivers/xbee: Support querying device for parameters, setting parameters, and structures association/startpan logic
* configs/clicker2-stm32: Fixes Xbee lower half ATTN poll logic
* drivers/xbee: Removes dependce on CONFIG_IEEE802154_NETDEV
* drivers/xbee: Supports MAC RESET.request primitive
* drivers/xbee: Exposes generic AT query to the rest of driver
* drivers/xbee: Sets local values when writing setting change to Xbee device
* drivers/xbee: Finish association logic
* drivers/xbee: Adds xbee_get_mhrlen( ) allocating enough space for API frame header to frame
* drivers/xbee: Finishes transmit/receive logic
* drivers/xbee: Fixes xbee_netdev to match logic in mac802154_netdev.c
* drivers/xbee: Rearranges logic to prevent a loop condition where recursion could potentially occur to the point of deadlocking the system
Approved-by: Gregory Nutt <gnutt@nuttx.org>
