arch/arm/src/tiva/common/tiva_timerlib.c:
* tiva_gptm_configure() and tiva_gptm_release(): Fix error: Was calling
tiva_emac_periphrdy() instead of tiva_gptm_periphrdy().
arch/arm/src/tiva/tiva_timer.h:
* Fix error in "abcde" description of bit flag defines.
kinetis:i2c transfer ensure correct result returned
kinetis_i2c_transfer released the mutex then fetched
the state, this resulted in returning the correct
results.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Move boards to boards folder
* boards: rename configs folder to boards
This is the proposed layout after the change:
boards: - folder containing board folders
<board>: - name of each board
drivers: - extra drivers specific for platform
include: - header files for the boars
scripts: - extra scripts specific for platform
src: - board specific code
tools: - extra tools specific for platform
<config>: - board specific configuration(s)
Note:
<xxx> names are dependent on platform
This is a logical change to aim to the arch layout but this is a
huge change it should be done in several steps to lower the risk.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Kconfig: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile.*: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Make.defs: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .sh: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .mk: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .c & .h: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .bat: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Rationale: TM4C1294NC is ambiguous:
TM4C1294NCPDT is a 128-TQFP
TM4C1294NCZAD is a 212-NFBGA
The TM4C1294NC part currently supported by NuttX is the TM4C1294NCPDT used on the TI EK-TM4C1294XL "Connected LaunchPad" (see configs/tm4c1294-launchpad). To ensure the correct part is fully specified, this commit updates all TM4C1294NC identifiers to TM4C1294NCPDT.
Rename:
CONFIG_ARCH_CHIP_TM4C1294NC to CONFIG_ARCH_CHIP_TM4C1294NCPDT
ARCH_CHIP_TM4C1294NC to ARCH_CHIP_TM4C1294NCPDT
TM4C1294NC to TM4C1294NCPDT
Rationale: In terms of firmware programming, there is no functional difference between these parts:
TM4C123GH6PMI7
TM4C123GH6PMI7R
TM4C123GH6PMT7
TM4C123GH6PMT7R
From a programming standpoint, all of the above parts are TM4C123GH6PM, which means it doesn't make sense to differentiate between PM and PMI. (The PM means 64-LQFP. The I means temperature range -40C to +85C. It could be T meaning -40C to +105C. The R means it ships in Tape and Reel packaging as opposed to Tray.)
arch/arm/include/tiva/chip.h:
arch/arm/include/tiva/tm4c_irq.h:
arch/arm/src/tiva/hardware/lm/lm3s_flash.h:
arch/arm/src/tiva/hardware/tm4c/tm4c_pinmap.h:
configs/tm4c123g-launchpad/README.txt:
configs/tm4c123g-launchpad/nsh/defconfig:
Rename: CONFIG_ARCH_CHIP_TM4C123GH6PMI to CONFIG_ARCH_CHIP_TM4C123GH6PM
arch/arm/src/tiva/Kconfig:
configs/Kconfig:
Rename: ARCH_CHIP_TM4C123GH6PMI to ARCH_CHIP_TM4C123GH6PM
arch/arm/src/tiva/hardware/tm4c/tm4c_memorymap.h:
Rename: CONFIG_ARCH_CHIP_TM4C123GH6PMI to CONFIG_ARCH_CHIP_TM4C123GH6PM
Remove redundant Peripheral Base Addresses section. There were two identical copies, one for CONFIG_ARCH_CHIP_TM4C123GH6PMI and another for CONFIG_ARCH_CHIP_TM4C123GH6PM.
Testing of the WiFi is minimal so far but functionality is proven. I'm specifically not happy that the driver doesn't recover elegantly from a DMA data checksum failure, but that is an issue that can be dealt with in due course ... I'm trying to get the rest of the interfaces fleshed out and the hardware proven so it can go for pre-production build. I _think_ there's only Bluetooth and USB-device left to implement now.
- Fix for mx25rxx driver as it does not work properly
- Add mx25rxx memory chip & smartfs support in b-l475e-iot01a/nsh config
- Update smartfs smart_scan() function
stm32f7: Fixes bad preprocessor logic preventing USB OTG HS to work when used without external ULPI.
Approved-by: David Sidrane <david.sidrane@nscdg.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Add support for LPC40xx family chips
* Corrected a few peripheral definitions and pin functions for the LPC17xx family.
Added configuration options, chip definitions, and additional pin functions for the LPC40xx family.
Added board configurations for Embedded Artists LPC4088 Quickstart board and LPC4088 Developer's kit. These configurations are still something of a work in progress. In particular, the LCD functionality is untested.
* First pass rename in *.c and *.h files.
* Renamed LPC17XX to LPC17XX_40XX in config files
* Rplaced LPC17xx with LPC17xx/LPC40xx in .c files
* Replaced LPC17xx with LPC17xx/LPC40xx in .h files
* Updated some documentation
* Working on moving directories
* moved arch/arm/src/lpc17xx and arch/arm/include/lpc17xx to lpc17xx_40xx
* Renamed LPC17_* constants / configuration options to LPC17_40_*
* Updated chip family name defines
* Renamed some chip-specific files
* Updated references to renamed files
* Updated references to lpc17_ to lpc17_40_
* Renamed source files from lpc17_* to lpc17_40_*
* Clean up white space
Approved-by: Gregory Nutt <gnutt@nuttx.org>
drivers/lcd/tda19988.c: Now uses the new common videomode structure of include/nuttx/video/videomode.h as do other video components.
video/, include/nuttx/video/videomode.h: Separate EDID and from videomode managment. They really are separate things.
