libs/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
syscall/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
wireless/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
Documentation/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
include/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
drivers/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
sched/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
configs: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/xtensa: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/z80: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/x86: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/renesas and arch/risc-v: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/or1k: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/misoc: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/mips: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/avr: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/arm: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
* Clocks were wrongly configured - way too fast because there is no primary divider on LPC4330
This is fixed by means of changing the definitions in the board.h file. I've edited the one for the lpc4330-xplorer board because I'm actually working with Versiboard and don't want to contribute that config just yet while I've still got the drains up on it.
* The LPC43_SDMMC_DELAY register was not being set
I suspect, in the 'real world', it's possible to get away without setting this, but I've added a register definition, default value and register access macros into arch/arm/src/lpc43xx/chip/lpc43_scu.h and then used them in arch/arm/src/lpc43xx/lpc43_sdmmc.c.
* The LPC43_SDMMC_BLKSIZ and LPC43_SDMMC_BYTECNT registers had the wrong values.
The management have already implemented a rather nice block level interface for the stm32 so I've just re-used that to write to these registers as required. I'm slightly nervous that accessing the configuration registers (SCR being the prime example) which has a much smaller block size may not be being done in the right way but it does seem to work correctly, so let's assume it's all OK until someone tells me otherwise.
These fixes have been tested with DMA-based read/write on a LPC4330. Speed via nsh is pretty low but I'm assuming that's just a buffering/implementation issue for now.
arch/arm/src/lpc43xx: Fix ethernet TX_EN pin definitions
TX_EN on LPC43xx can be routed via P0.1 and PC.4 in both
MII and RMII mode.
Before, P0.1 was hardcoded for MII and PC.4 was hardcoded for RMII.
Also, the definitions used inconsistent naming (TXEN vs. TX_EN).
Approved-by: GregoryN <gnutt@nuttx.org>
lpc17: Removed duplicate configuration variable definitions from Kconfig: CONFIG_USBHOST_BULK_DISABLE, CONFIG_USBHOST_INT_DISABLE, and USBHOST_ISOC_DISABLE. These are global USBHOST configurations and are all defined in drivers/usbhost/Kconfig.
lpc17: Correct scope of naming of configuration variables: CONFIG_USBHOST_TDBUFFERS->CONFIG_LPC17_USBHOST_TDBUFFERS, CONFIG_USBHOST_TDBUFSIZE->CONFIG_LPC17_USBHOST_TDBUFSIZE, and CONFIG_USBHOST_IOBUFSIZE->CONFIG_LPC17_USBHOST_IOBUFSIZE
lpc17: Correct scope of naming of configuration variables: CONFIG_USBHOST_NEDS->CONFIG_LPC17_USBHOST_NEDS and CONFIG_USBHOST_NTDS->CONFIG_LPC17_USBHOST_NTDS
lpc17: Correct scope of naming of configuration variable: CONFIG_USBHOST_OHCIRAM_SIZE->CONFIG_LPC17_OHCIRAM_SIZE
arch/arm: Remove support for CONFIG_ARMV7M_CMNVECTOR. It is now the only vector support available. Also remove CONFIG_HAVE_CMNVECTOR. That no longer signifies anything."
arch/arm/src/stm32: This commit removes support for the dedicated vector handling from the STM32 architecture support. Only common vectors are now supported.
Squashed commit of the following:
configs/*/README.txt: Replace each occurrence of './configure.sh' with 'tools/configure.sh'
configs/*/README.txt: Remove 'cd ..' after each './configure.sh'
configs/*/README.txt: Remove 'cd -' after each './configure.sh'
configs/*/README.txt: Remove 'cd tools' before each './configure.sh'
configs/README.txt: Remove instruction to CD tools/ before running configure.sh.
Provide a user defined callback context for irq's, such that when
registering a callback users can provide a pointer that will get
passed back when the isr is called.
