- Add defconfig and board specific files
- Create mpfs/common for code which is shared between MPFS boards.
- Add support for GPIO driven EMMCSD mux.
- Move DDR Libero definitions from arch to boards.
Signed-off-by: Jani Paalijarvi <jani.paalijarvi@unikie.com>
When waiting for a response to a sent command, the command
complete bit (MPFS_EMMCSD_SRS12_CC) should always guarantee
the completion of that particular command. There's no need
to have some combinations skipping the check of the command
complete bit. Thus, remove the 'waitbits' parameter as it's
unnecessary.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
script.
These functions are strongly declared and thus will be used instead of
any other implementation. Furthermore, necessary Kconfig options are
selected to avoid building those function from NuttX's C library.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
Currently configuring the uart3/4 as the serial console
doesn't work. Apply proper changes in mpfs_config.h that
enables the following configuration options:
- CONFIG_UART3_SERIAL_CONSOLE
- CONFIG_UART4_SERIAL_CONSOLE
Also, fix a typo in mpfs_lowputc.c that gives a compile
error if defined.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
When enable DEBUG_TCBINFO config, a global struct will
provide, then debuggers can aware nuttx task infomation.
Signed-off-by: zhuyanlin <zhuyanlin1@xiaomi.com>
cppcheck reports the following:
arch/risc-v/src/mpfs/mpfs_emmcsd.c:2375:22: error: Uninitialized variable: waitbits [uninitvar]
while (!(status & (waitbits | MPFS_EMMCSD_SRS12_EINT))
The finding is positive and this patch initializes it to
zero properly.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
1. Wi-Fi and BLE use common PHY functions.
2. Fix Wi-Fi & BLE coexist adapter error.
3. Update esp-wireless-drivers-3rdparty, provide coexist protection for connection.
1. Fix the issue that Wi-Fi can't connect to some special routers occasionally.
2. Support Wi-Fi 12/13 channel active scanning by default.
3. Update Wi-Fi driver code to fix issue of failure to send pkt.
4. Replace software random with hardware random
5. Fix Wi-Fi mode start error
E51 may configure the L1 and L2 caches. Once configured,
no reconfiguration is possible after hardware reset is
issued.
L2 is 16-way set associative with write-back policy. The
size 2 MB, from which 1 MB is utilized with the values
provided here. That's a total of 8 ways. The rest of the
L2 is left out for the bootloader usage.
mpfs_enable_cache() first checks the bootloader usage
doesn't overlap with the cache itself, thus providing a
set of functional values.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
So far the SD-card functionality has been tested with
the driver. Now, also the internal eMMC has been tested
working with this patch. This patch applies IOMUX and
clock settings that have been tested working with the
internal eMMC in the Polarfire Icicle kit.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This adds the proper flag for introducing the DDR
support. Also call the mpfs_ddr_init() at the
proper location.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This adds DDR training. The training has a small chance of failing,
and then the training is restarted.
DDR training cannot be done meaningfully while the software is
in DDR. If the system is intended to run from eNVM, like a
bootloader, the linker script should be tuned to utilize the envm
region as follows:
envm (rx) : ORIGIN = 0x20220100, LENGTH = 128K - 256
l2lim (rwx) : ORIGIN = 0x08000000, LENGTH = 1024k
256 bytes are reserved for the system; The fixed block may be
installed from the 'hart-software-services' -repository:
https://github.com/polarfire-soc/hart-software-services.git
For example, the 256-byte image: hss-envm-wrapper-bm1-dummySbic.bin
may be prepended on the nuttx bootloader image in the following
manner:
cat hss-envm-wrapper-bm1-dummySbic.bin > nuttx_bootloader.bin
cat nuttx.bin >> nuttx_bootloader.bin
riscv64-unknown-elf-objcopy -I binary -O ihex --change-section-lma
*+0x20220000 nuttx_bootloader.bin flashable_image.hex
This provides an image 'flashable_image.hex' that may be flashed on
the eNVM region via Microsemi Libero tool.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
