Co-authored-by: Jari van Ewijk <jari.vanewijk@nxp.com>
Co-authored-by: David Sidrane <david.sidrane@nscdg.com>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
imxrt:Kconfig fix formatting
imxrt:usbphy move IMXRT_USBPHY{1|[2]}_BASE to memory map
imxrt:lpspi Fix build breakage from adding 1170
imxrt:Finish 1170 iomux and clockconfig versioning
imxrt:Remove duplicate imxrt_clock{off|all}_lpi2c4
imxrt:pmu remove duplicate dcd non 117x header
imxrt:lpspi Fix unused var warnings
imxrt:lpi2c Fix unused var warnings
imxrt:lowputs Fix unused var warnings
imxrt:imxrt117x_dmamux fix duplicate entries
imxtr:serial Use IOMUX_PULL_{UP|DOWN} and map IOMUX V1 to them
imxrt:MPU Support the 1170
imxrt:dmamux Alias IMXRT_DMAMUX0_BASE as IMXRT_DMAMUX_BASE
imx1170:ccm Alias CCM_CCGR_DMA & CCM_CCGR_SNVS_LP for compatiblity
Author: Peter van der Perk <peter.vanderperk@nxp.com>
IMXRT7 Add LPUART 9/10/11/12 support
Author: David Sidrane <david.sidrane@nscdg.com>
imxrt:1170pinmux Add QTIMER pins
imxrt:1170pinmux Add GPT pins
imxrt:1170pinmux Add FLEXPWM pins
imxrt1170:pinmap Add GPIO_ENET_1G pinning
imxrt:enet Support ENET_1G
imxrt:periphclks rt1170 does not have canX_serial clock
imxrt:flexcan:Layer imxrt_ioctl
imxrt117x:memorymap added CAN3
imxrt:ADC support ver1 and ver2 for imxrt117x
imxrt:imxrt117x_ccm Align timer naming with other imxrt QTIMERn->TIMERn
imxrt:imxrt117x_ccm align CCM names with rt106x
imxrt:XBAR support larger number of selects needed on imxrt1170
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
FlexSPI AHB Region support, PIT rename for compatiblity
imxrt:USB Analog add VBUS_VALID_3V
FlexSPI expand prefetch registers for IMXRT117X
imxrt:Support Initialization of FlexRam without Running from OCRAM
imxrt: ocotp add UNIQUE_ID register definition
imxrt: enet use ocotp unique_id
imxrt: enet fixes for imxrt117x
imxrt: ethernet pinmux sion enable
imxrt:imxrt_periphclk_configure add memory sync
Flush the pipeline to prevent bus faults, by insuring a
peripheral is clocked before being accessed on return from
this function.
imxrt:Restructure gpioN to padmux mapping
imxrt:Add imxrt1170 daisy
imxrt: correct power modes for imxrt117x fixing hang on WFI
imxrt: imxrt117x TCM MPU config
imxrt: FlexRAM clocking DIV0 setup
imxrt: 117x periphclocks wait for status bit
imxrt: iomucx set pad settings correctly and allow reconfiguration
imxrt: enet align buffers 64-byte for optimal performance
Add DSC barriers for write-through cache support
imxrt: imxrt1170 use FlexCAN FD/ECC features
imxrt:iomuxc_ver2 (117x) SD_B1 and DISP_B1 use PULL feild not PUE/PUS
imxrt:Fix 1170 SNVS addressing
imxrt: enet set mii clock after ifdown so that phy keep working
nxstyle fixes
imxrt: preprocessor and include fixes
Fix configs
imxrt1170-evk clean defconfig
When I try to set priorities in certain programs, such as init_priority(HIGH_PRIORITY), I've noticed that during linking, there's no guarantee that the programs will be compiled in the sequence I've specified based on priority. This has led to some runtime errors in my program.
I realized that in the ld file, when initializing dynamic arrays, there's no assurance of initializing init_array.* before init_array. This has resulted in runtime errors in the program. Consequently, I've rearranged the init_array.* in the ld file of NuttX to be placed before init_array and added a SORT operation to init_array.* to ensure accurate initialization based on priorities during linking.
replace *(.init_array .init_array.*) with KEEP(*(.init_array .init_array.*)).
The KEEP statement within a linker script will instruct the linker to keep the specified section, even if no symbols inside it are referenced. This statement is used within the SECTIONS section of the linker script. This becomes relevant when garbage collection is performed at link time, enabled by passing the --gc-sections switch to the linker. The KEEP statement instructs the linker to use the specified section as a root node when creating a dependency graph, looking for unused sections. Essentially forcing the section to be marked as used.
Signed-off-by: cuiziwei <cuiziwei@xiaomi.com>
use PTHREAD_CLEANUP_STACKSIZE to enable or disable interfaces pthread_cleanup_push() and pthread_cleanup_pop().
reasons:(1)same as TLS_TASK_NELEM (2)it is no need to use two variables
Signed-off-by: yanghuatao <yanghuatao@xiaomi.com>
This commit updates configuration pikron-bb (configuration for open
hardware experimental board) to support permanent magnet sychnronous
motor control. This includes setup of PWM, GPIO and ADC peripherals.
Required follow up changes are done to pinout definition.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
The imxrt1064, imxrt1064, and teensy-4.x board configs would fail to
build when CONFIG_USERLED_LOWER was enabled, due to a missing header in
imxrt_appinit.c and an unset local define.
Verified a build succeds for the specified boards with the following
defconfig modifications:
# CONFIG_ARCH_LEDS is not set
CONFIG_USERLED=y
CONFIG_USERLED_LOWER=y
Tested the "leds" Led driver example on a Teensy 4.1.
## Summary
A lot of linker scripts were listed twice, once for unix, once for windows.
This PR cleans up the logic so they're only listed once.
## Impact
Any opportunity to use a single source of truth and reduce lines of code is a win!
## Testing
CI will test all build
This reverts commit 45672c269d.
Because:
* It's very confusing to have cc as LD.
* I don't see what "-nostartfiles -nodefaultlibs" in LDFLAGS are
supposed to do when we use LD directly. It would be simpler to
remove them from our LDFLAGS.
This commit adds option for Teensy 4.x board to initialize CAN3 as can0.
The reason of this is the CAN FD capability of CAN3. This commit also
disables tickless mode support for pikron-bb configuration as this option
started causing hard faults which are yet to be solved.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>