sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
27,431 Commits 1 Branch 0 Tags 291 MiB
9e349f4335
Commit Graph

455 Commits

Author SHA1 Message Date
Wolfgang Reißnegger
9e349f4335 SAM3/4: Remove unused 'halted' flag in UDP driver. 2016-11-18 17:23:21 -08:00
Wolfgang Reißnegger
c7ef82c546 SAM3/4: Add delay between setting and clearing the endpoint RESET bit in sam_ep_resume(). 
We need to add a delay between setting and clearing the endpoint reset
bit in SAM_UDP_RSTEP. Without the delay the USB controller will (may?)
not reset the endpoint.

If the endpoint is not being reset, the Data Toggle (DTGLE) bit will
not to be cleared which will cause the next transaction to fail if
DTGLE is 1. If that happens the host will time-out and reset the bus.

Adding this delay may also fix the USBMSC_STALL_RACEWAR in
usbmsc_scsi.c, however this has not been verified yet.
 2016-11-18 17:23:21 -08:00
Gregory Nutt
19c1c9d78b All timer lower half drivers. Port Sebastien's changes to all all other implementations of the timer lower half. Very many just and untested. Expect some problems. 2016-11-17 15:03:31 -06:00
Gregory Nutt
bb6bfa633e arch: Disable priority inheritance on all semaphores used for signaling in all SD card drivers 2016-11-03 15:13:27 -06:00
Gregory Nutt
8b07aa6f7c arch: Disable priority inheritance on all semaphores used for signaling in all SPI drivers 2016-11-03 14:51:44 -06:00
Gregory Nutt
e1cd9febbf arch: Disable priority inheritance on all semaphores used for signaling in all I2C/TWI drivers 2016-11-03 14:23:42 -06:00
Frank Benkert
cf5fdf1f8f SAM Watchdog: Register the watchdog device at the configured device path CONFIG_WATCHDOG_DEVPATH vs. hard-coded /dev/wdt 2016-10-21 07:09:20 -06:00
Gregory Nutt
1c20376e39 SAM GPIO: Apply Wolfgang's change for SAM3/4 to SAMA5 and SAMV7 2016-09-20 15:33:31 -06:00
Wolfgang Reißnegger
3f22b63321 SAM3/4: Fix GPIO pull-up/down code. 
Enabling the pull-down resistor while the pull-up resistor is still enabled
is not possible. In this case, the write of PIO_PPDER for the relevant I/O
line is discarded. Likewise, enabling the pull-up resistor while the
pull-down resistor is still enabled is not possible. In this case, the
write of PIO_PUER for the relevant I/O line is discarded.
 2016-09-20 13:32:04 -07:00
Gregory Nutt
4dc3521743 All SAM Ethernet Drivers: Add support so that the drivers can be built with CONFIG_NET_MULTIBUFFER=y 2016-09-20 08:56:36 -06:00
Gregory Nutt
046acf6b54 Add a simulated oneshot lowerhalf driver 2016-08-12 13:14:03 -06:00
Gregory Nutt
b4e8876b09 Correct some spacing 2016-08-12 12:41:49 -06:00
Gregory Nutt
82b86cdcf3 oneshot interface: max_delay method should return time in a standard struct timespec form. 2016-08-12 11:33:10 -06:00
Gregory Nutt
61b0ac06bf Missed a dependency in last set of commits 2016-08-11 17:20:12 -06:00
Gregory Nutt
a5a776e223 SAM4CM: Add option to support oneshot timer without free-running timer. Add oneshot lower half driver. 2016-08-11 17:04:19 -06:00
Gregory Nutt
0e35bad987 Update some comments 2016-08-11 10:12:04 -06:00
Gregory Nutt
7823a1680e Update a comment 2016-08-09 17:08:03 -06:00
Gregory Nutt
698d6d1294 SAM3/4: Extend clocking logic to enable clocking on ports D-F 2016-08-09 17:05:11 -06:00
Wolfgang Reissnegger
cf35bb0b18 SAM3/4 GPIO: Enable peripheral clock for GPIO port when GPIO is configured as input. 
The value of a GPIO input is only sampled when the peripheral clock for
the port controller the GPIO resides in is enabled. Therefore we need
to enable the clock even when polling a GPIO.
 2016-08-09 13:23:05 -07:00
Gregory Nutt
e895e19b9f Minor changes from review of last PR 2016-07-24 07:45:46 -06:00
Wolfgang Reissnegger
c0fa319f2b SAM3/4 UDP: Fix handling of endpoint RX FIFO banks. 
This fixes a race condition where the HW fills a FIFO bank while the SW is
busy, resulting in out of sequence USB packets.
 2016-07-23 20:11:04 -07:00
Wolfgang Reissnegger
cc191a977d SAM3/4 UDP: Remove redundant EP state assignment. 2016-07-23 20:11:03 -07:00
Wolfgang Reissnegger
f3a6a40f62 SAM3/4 Serial: Fix warning when CONFIG_SUPPRESS_UART_CONFIG is set. 2016-07-23 16:23:49 -07:00
Gregory Nutt
96d5b734a8 Add missing TWI definitions 2016-07-21 08:01:59 -06:00
Gregory Nutt
18059d6821 Restore Wolfgang Reissnegger's PR as submitted. My mistake is it late here. 2016-07-14 18:39:51 -06:00
Wolfgang Reissnegger
f982180ec7 SAM3/4 Timer: Remove broken definitions for BMR register. 
Per documentation SAM4S and SAM4E have the BMR register values
as they are already defined. No need for chip specific values.

In addition:
 - CONFIG_ARCH_CHIP_SAM4s has wrong lower case 's' so the definitions would
   not be used anyways for SAM4S builds.
 - TC_BMR_TC2XC2S_TIOA2 does not make sense. There is no way to loop back
   TC2's TIOA2 into itself.
 2016-07-14 18:17:05 -06:00
Wolfgang Reissnegger
d89e062c06 SAM3/4 I2C: Fix reversed logic in twi_startmessage(). 2016-07-09 06:51:07 -06:00
Wolfgang Reissnegger
f4adb82fe7 [sam34][dacc] Bugfix: DACC_WPMR_WPKEY_MASK -> DACC_WPMR_WPKEY 2016-06-23 17:12:24 -07:00
Gregory Nutt
aed4d0e198 Missed a few *llinfo() to *info() conversions 2016-06-20 16:24:09 -06:00
Gregory Nutt
2a751068e6 Without lowsyslog() *llerr() is not useful. Eliminate and replace with *err(). 2016-06-20 12:44:38 -06:00
Gregory Nutt
43eb04bb8f Without lowsyslog() *llinfo() is not useful. Eliminate and replace with *info(). 2016-06-20 11:59:15 -06:00
Gregory Nutt
d40a473f72 Without lowsyslog() *llwarn() is not useful. Eliminate and replace with *warn(). 2016-06-20 09:37:08 -06:00
Gregory Nutt
832efae5d8 Fix some debug output statements that were changed and lost their ll-ness 2016-06-18 09:41:55 -06:00
Gregory Nutt
3fa41c0f18 Kconfig files: Fix some dependencies that have CONFIG_ in the variable name 2016-06-17 19:30:19 -06:00
Gregory Nutt
0d3ecb3ddd Fix another victim of the mass name changes: xyz_errmonitor->xyz_dbgmonitor 2016-06-17 07:00:33 -06:00
Gregory Nutt
f35086dbf7 Change *err() to either info() or err(ERROR:..), depending upon if an error has occurred. 2016-06-16 16:30:45 -06:00
Gregory Nutt
801d661423 Change *err() to either info() or err(ERROR:..), depending upon if an error has occurred. 2016-06-16 15:10:57 -06:00
Gregory Nutt
0c8c7fecf0 Add _ to the beginning of all debug macros to avoid name collisions 2016-06-16 12:33:32 -06:00
Gregory Nutt
b7f0fbc073 Centralize definitions associated with CONFIG_DEBUG_RTC 2016-06-16 07:39:23 -06:00
Gregory Nutt
37b9742189 Centralize definitions associated with CONFIG_DEBUG_TIMER 2016-06-16 07:16:25 -06:00
Gregory Nutt
6b517ed017 Centralize definitions associated with CONFIG_DEBUG_WATCHDOG 2016-06-16 06:28:04 -06:00
Gregory Nutt
5c89b18af8 Centralize definitions associated with CONFIG_DEBUG_I2C 2016-06-15 16:30:12 -06:00
Gregory Nutt
ba03134bed Centralize definitions associated with CONFIG_DEBUG_SPI 2016-06-15 10:41:13 -06:00
Gregory Nutt
a97d3ae707 Centralize definitions associated with CONFIG_DEBUG_GPIO 2016-06-15 09:20:23 -06:00
Gregory Nutt
c4e6f50eac Centralize definitions associated with CONFIG_DEBUG_IRQ 2016-06-15 08:35:22 -06:00
Gregory Nutt
0f249016a0 Eliminate some warnings 2016-06-13 14:01:32 -06:00
Gregory Nutt
eac916c907 Fix some warnings 2016-06-13 11:48:20 -06:00
Gregory Nutt
a1469a3e95 Add CONFIG_DEBUG_ERROR. Change names of *dbg() * *err() 2016-06-11 15:50:49 -06:00
Gregory Nutt
e99301d7c2 Rename *lldbg to *llerr 2016-06-11 14:55:27 -06:00
Gregory Nutt
1cdc746726 Rename CONFIG_DEBUG to CONFIG_DEBUG_FEATURES 2016-06-11 14:14:08 -06:00