If sched lock before irq save, and irq handler do post, scheduler will
be delayed after WFI until next sched unlock. which is not acceptable.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
pm process should be done by chip specific, but we can provide a standard
flow, then vendor & chip can only focus on handle different state change.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
critical_section is not compatible with irq disabled, have to delay the
wd_start after spin_unlock_irqrestore.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
when the vsync comes, fb drivers should call fb_vsync_pollnotify to notify POLLPRI, so that users can catch the synchronization time of vsync and do something.
Signed-off-by: jianglianfang <jianglianfang@xiaomi.com>
1. increase CDCECM_MXDESCLEN to avoid memory overrun when sending
configuration description(mkcfmdesc) information
2. correct the request structure used in the notify phase
3. disable unused configuration options
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
optimize the interaction flow associated with network drivers to reduce
the amount of code and improve compatibility
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
When our netstack is replying packets when processing RX, the replied
packets will be sent without considering of TX quota because we don't
want to drop them. Now we may delay them by pushing them to a queue and
send them later, which can always keep quota working.
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
If per tick is set to 10ms, it will cause nxsig_usleep(1000) in the
sdio driver to sleep for 19ms, which is much longer than the
expected 1ms, resulting in very low write performance. Add option to
reduce CPU hogging by using sched_yield(), though it may also affect
write performance when the CPU is busy.
Signed-off-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
Reviewed-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Jacky Cao <Jacky.Cao@sony.com>
Tested-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
In mmcsd_cardidentify(), the clock is not enabled before issuing
CMD0, and the clock has been disabled in mmcsd_removed(). It makes
no sense to enable the clock after issuing CMD0, because when CMD0
is issued, it will exit with error due to the clock is not enabled.
Signed-off-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
Reviewed-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Jacky Cao <Jacky.Cao@sony.com>
Tested-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
Prompts for capacity, speed mode and bus width after eMMC
initialization is completed.
Signed-off-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
Reviewed-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Jacky Cao <Jacky.Cao@sony.com>
Tested-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
According to the eMMC specification, in Backwards Compatibility
with legacy MMC card mode, the frequency of the SD clock must be
0-26 MHZ; in high speed SDR mode, it must be 0-52MHZ. So we should
switch to high speed SDR mode if the clock frequency is higher than
26MHZ.
Signed-off-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
Reviewed-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Jacky Cao <Jacky.Cao@sony.com>
Tested-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
CMD6 can use these macros to set any writable EXT_CSD field, not
just the bus width, so optimize these macro definitions to make
them general.
Signed-off-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
Reviewed-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Jacky Cao <Jacky.Cao@sony.com>
Tested-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
All eMMC devices support 4-bit bus width, so we should mark the
device as supporting 4-bit bus width after detecting that the
device type is eMMC.
Signed-off-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
Reviewed-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Jacky Cao <Jacky.Cao@sony.com>
Tested-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
In order to better use the Android goldfish emulator,
a GPU FB driver has been added. This allows the goldfish
emulator side to achieve more flexible display effects,
such as UI skins.
Signed-off-by: rongyichang <rongyichang@xiaomi.com>
According to Virtual I/O Spec:
When using legacy interfaces, transitional drivers which have not negotiated VIRTIO_F_ANY_LAYOUT MUST use a single descriptor for the struct virtio_net_hdr on both transmit and receive, with the network data in the following descriptors.
https://docs.oasis-open.org/virtio/virtio/v1.2/cs01/virtio-v1.2-cs01.html#x1-2280006 (Section 5.1.6.6)
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
Refactoring path logic to prevent logic flaws, direntry size bug fix to allow proper direntry traversal, open free bug fix to prevent memory leak after close.
Signed-off-by: Saurav Pal <resyfer.dev@gmail.com>
Add configuration and driver support for the SSD1681 1.54 inch e-paper display,
including the necessary waveforms and settings for proper operation. This extends
the existing SSD1680 e-paper driver to accommodate the new display module.
The changes involve updates to the Kconfig file for additional configuration options,
modifications to the driver implementation in ssd1680.c to include SSD1681 specific
logic, and updates to the header file ssd1680.h to reflect the added support.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
When setting the sample rate (`es8311_setsamplerate`) and the bits
per sample (`es8311_setbitspersample`), check their return value in
`es8311_configure`. Also, this commit ensures that these functions
are called after `es8311_reset` to avoid these values to be set to
the default values.
Check if only one driver is used as console to avoid a non-working console
because a different one is selected and has higher priority than the one we wanted
This adds DRIVERS_VIRTIO_SERIAL_CONSOLE config and related logic to
virtio serial so that it can be used as console device. Note that
due to its dependency on OS services, this console is available late
so it is not proper for debugging too early booting issues.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This driver implements `read`, `write`, `open`, `close` and `ioctl`
interfaces to the SHT4X temperature and humidity sensor on an I2C bus.
The read implementation is that of a character driver for easy
debugging, while `ioctl` provides an interface to the sensor's raw data
collection and heating functionality.
- use 'lan9250_ioctl' to set and get the value of lan9250 phy register
- use `lan9250_uninitialize` to un-initialize the ethernet driver
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
This commit moves can_bytes2dlc and can_dlc2bytes from kernel internal
functions to API. These functions are necessary to convert bytes to
dlc for CAN FD frames and has to be accessible from the application
since can_hdr_s does not store message length in bytes but directly in
dlc.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
as we always want to take critical_section, and it is not long time job,
take mutex is not necessary, use spinlock_irq_save as a replace is
better, dont't have to take global critial_section in pm.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
When initialising the SJA1000 peripheral on some implementations
(SJA1000_FDTOL), "releasing" the buffer when the Rx buffer is empty
causes a buffer pointer misalignment.
On peripheral initialise, remove the flag to "release" the buffer.
This should be safe for all systems using the SJA1000 CAN controller
as a "reset" to the peripheral clears the Rx FIFO.
/home/raiden00/git/RTOS/nuttx/nuttx/drivers/wireless/gs2200m.c:2071:3: note: ‘snprintf’ output between 7 and 9 bytes into a destination of size 8
2071 | snprintf(cmd, sizeof(cmd), "ATE%d\r\n", on);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sched implementation not depends on macro abstraction, so revert below commit:
This reverts commit 4e62d0005a
This reverts commit 0f0c370520
This reverts commit ad0efd04ee
Signed-off-by: chao an <anchao@lixiang.com>
After change, when CONFIG_PM_NDOMAINS > 1,
the pm_register will not able to get notificaion
from not PM_IDLE_DOMAIN.
Should use pm_domain_register as a replacement.
Isolate domains from global callbacks can decrease
not necessary execution, and reduce the
lock instruction requirements.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
MCP794XX supports digital trimming that periodically adds or subtracts
clock cycles, resulting in small adjustments in the internal timing.
This way inaccuracies of clock source can be compensated.
This commit adds option to set the trimming register for MCP794XX.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit adds configuration option CONFIG_MCP794XX_DATETIME_UTC.
If set, the datetime is stored in UTC instead of local time. The
default value is kept at local time to keep backwards compatibility
with devices currently using the RTC.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
DAC driver uses CONFIG_DAC_FIFOSIZE, but this is not configurable
from Kconfig. This adds the missing option and allows to set DAC
FIFO size from the configuration.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
only when first time change state can hold WFI for enough time thresh,
allow second time goto target state,
suitable for the case when wakeup from sleep too slow, etc.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
There is no need to call rwb->rhreloade() when nblocks is 0,
and some platform(eg: BES) has the limit that the parameter
of len in pltatform flash read function cant't be 0.
Swap the sequence of domain state update and statechanged callback,
Make sure inside statechanged callback can get the old domain state.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
Some drivers may set too big quota by accident and consume all of our
buffers, so we add a check when registering devices.
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
Fix a bug which causes that 1-bit mode is always selected.
This happens even if the driver sets SDIO_CAPS_4BIT capability
in case of the card and the host support 1- and 4-bit wide bus.
Signed-off-by: Jani Paalijarvi <jani.paalijarvi@unikie.com>
There might be multiple expanders, one with interrupt used and other
without. This commit fixes initial incorrect interrupt design by
introducing ICJX_INT_ENABLE config option.
Also fixes naming of ICJX_MULTIPLE option.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Also extend the "struct phy_desc_s" to support for 1GB PHY's, the speed
detection always needs more than one bit.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
purpose:
1 sched_lock is very time-consuming, and reducing its invocations can improve performance.
2 sched_lock is prone to misuse, and narrowing its scope of use is to prevent people from referencing incorrect code and using it
test:
We can use qemu for testing.
compiling
make distclean -j20; ./tools/configure.sh -l qemu-armv8a:nsh_smp ;make -j20
running
qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic -machine virt,virtualization=on,gic-version=3 -net none -chardev stdio,id=con,mux=on -serial chardev:con -mon chardev=con,mode=readline -kernel ./nuttx
We have also tested this patch on other ARM hardware platforms.
Signed-off-by: hujun5 <hujun5@xiaomi.com>
issue:
in rwb_wrflush():
memmove(rwb->wrbuffer + padblocks * rwb->blocksize,
rwb->wrbuffer, rwb->wrnblocks * rwb->blocksize);
when the offest from rwb->wrblockstart to startblock plus rwb->wrnblocks is greater
than rwb->wralignblocks, it will be causing memory overflow since rwb->wrbuffer is
allocated rwb.wrmaxblock(rwb.wralignblocks) blocks.
fix:
Let us ensure that the wrblockstart in rwbuffer must be aligned according to
wralignblocks after writing, so there is no need to perform memmove when flushing
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
When usb is re-enumerated due to the reset signal, we need to push
the rx_pending message into the serial port buffer.
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
when the offest from rwb->wrblockstart to startblock
plus rwb->wrnblocks is greater than rwb->wralignblocks,
it will be causing memory overflow since rwb->wrbuffer is
allocated rwb.wrmaxblock(rwb.wralignblocks) blocks.
iC-JX expander has NINT (not interrupt) pin that goes to logical zero
if interrupt occurs. This commit adds support for iC-JX options settings
that allows to enable the interrupt for defined input pins.
The interrupt is handled in HP worker thread to avoid waiting for SPI
transfers in interrupt context. Board has to configure interrupt event
for GPIO pin connected to NINT.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Fix default_value of ioctl(VIDIOC_QUERYCTRL)(id=V4L2_CID_3A_STATUS)
to AE operating and AWB operating, because both AE and AWB are
automatical adjustment mode by default.
Because the exposure time and ISO sensitivity are adjusted automatically
by default, the default value can not be defined.
So, return the value out of range as the default_value of
ioctl(VIDIOC_QUERYCTRL).
which is useful in the m2m usage scenario, by replacing the first
argument of callback from "struct v4l2_ops_s *" to "struct file *"
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
