Pre-allocated files to avoid allocator access during thread creation
phase, For functional safety requirements, increase
CONFIG_NFILE_DESCRIPTORS_PER_BLOCK could also avoid allocator access
caused by the file descriptor exceeding the limit.
For Task Termination, the time consumption will be reduced ~3us (Tricore TC397 300MHZ):
10.65(us) -> 7.35(us)
NOTE:
This commit will not waste of extra heap, just pre-allocates the list of files for task_group.
Signed-off-by: chao an <anchao@lixiang.com>
This change is missing from the below commit:
| commit 7cb1f3b3c0
| Author: chao an <anchao@lixiang.com>
| Date: Tue Mar 5 10:23:30 2024 +0800
|
| sched/group: replace group_findbypid to task_getgroup
|
| Task group could find from process id, replace group_findbypid to
| task_getgroup to simplify the search logic
|
| Signed-off-by: chao an <anchao@lixiang.com>
Signed-off-by: chao an <anchao@lixiang.com>
Reproduce:
configure:
./tools/configure.sh qemu-armv7a:nsh -j8
open kasan:
CONFIG_MM_KASAN=y
run:
qemu-system-arm -cpu cortex-a7 -nographic -machine virt,virtualization=off,gic-version=2 -net none -chardev stdio,id=con,mux=on -serial chardev:con -mon chardev=con,mode=readline -kernel ./nuttx
error:
run hanged
Rootcause:
In Qemu armv7a, the ram-end reserved for MMU PGTABLE:
And the up_allocate_heap() directly use the ram-end for heap in arch/arm/src/common/arm_allocateheap.c
*heap_size = CONFIG_RAM_END - g_idle_topstack;
Then they are conflict.
Usually, we won't use the heap end, so can't find the error.
BUT, the KASAN will use the heap end for shadow, so found the error.
Resolve:
up_allocate_heap() consider of MMU, re-define the RAM_END at chip.h
Signed-off-by: ligd <liguiding1@xiaomi.com>
The maximum startup parameters have been checked accordingly in nxtask_setup_stackargs(),
let us save argument counter to avoid limit check.
Signed-off-by: chao an <anchao@lixiang.com>
Task group could find from process id, replace group_findbypid to
task_getgroup to simplify the search logic
Signed-off-by: chao an <anchao@lixiang.com>
This commit adds support for TX DMA transfers for USART peripheral. Code
refactor in sam_serial.h was also required in order to have correct
defines for all possible cases (both RX and TX DMA used, just one used,
none used).
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
When an application is being loaded `up_addrenv_create ` calls
`create_region` to create the address environment. Only the first
entry is mapped when the region is created. Virtual memory that is
not mapped will trigger an exception when accessed. Other memory
pages are allocated and mapped on-demand. This enables setting
larger heap and stack for the process without compromising the
overall system memory.
Current `CONFIG_PAGING` refers to an experimental implementation
to enable embedded MCUs with some limited RAM space to execute
large programs from some non-random access media.
On-demand paging should be implemented for the kernel mode with
address environment implementation enabled.
Add support for static tcb, applications in some special case can
initialize system resources in advance through static tcb.
| static struct task_tcb_s g_tcb;
|
| memset(&g_tcb, 0, sizeof(struct task_tcb_s));
| g_tcb.cmn.flags = TCB_FLAG_TTYPE_KERNEL;
| nxtask_init(&g_tcb, "PTCB", 101, NULL, 1024, ptcb_task, NULL, NULL, NULL);
|
| ...
| nxtask_activate(&g_tcb.cmn);
Signed-off-by: chao an <anchao@lixiang.com>
We will first check whether the target file path exists. If it does not exist, we will check whether the common exists. If not, we will restore the path that should be spliced at the beginning.
Signed-off-by: chenrun1 <chenrun1@xiaomi.com>
We'll look for ETC resources from two paths
1.board/src/etc
2.common/etc
Search for the content in the board/src/etc directory first
Signed-off-by: chenrun1 <chenrun1@xiaomi.com>
Previously we need turn off the PMP locks in K230 vendor u-boot to use
NuttX, this complicates the setup process. This patch supports running
NuttX with original vendor u-boot so that to reduce setup complexity.
It also enables empty NSH prompt string in AMP master config as the apps
side support is ready.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
