nuttx

a1x

Without lowsyslog() *llerr() is not useful. Eliminate and replace with *err().

2016-06-20 12:44:38 -06:00

arm

Replaces last three commits. Does the same thing, but does it in a way that does not change the usage model.

2016-06-21 05:26:08 -06:00

armv6-m

Replaces last three commits. Does the same thing, but does it in a way that does not change the usage model.

2016-06-21 05:26:08 -06:00

armv7-a

Replaces last three commits. Does the same thing, but does it in a way that does not change the usage model.

2016-06-21 05:26:08 -06:00

armv7-m

Replaces last three commits. Does the same thing, but does it in a way that does not change the usage model.

2016-06-21 05:26:08 -06:00

armv7-r

Fix STM32 RTC Alarm interrupts. They were being enabled BEFORE the interrupt system was being initialized.

2016-07-23 10:36:06 -06:00

c5471

Fix names of pre-processor variables used in header file idempotence

2016-08-06 18:48:45 -06:00

calypso

Fix names of pre-processor variables used in header file idempotence

2016-08-06 18:48:45 -06:00

common

2016-07-20 13:15:37 -06:00

dm320

Fix names of pre-processor variables used in header file idempotence

2016-08-06 18:48:45 -06:00

efm32

Make bit-order SPI H/W feature configurable for better error detection

2016-08-08 11:54:13 -06:00

imx1

Remove lowsyslog(). The new syslog() includes all of the functionality of lowsyslog(). No longer any need for two interfaces.

2016-06-20 08:57:08 -06:00

imx6

Centralize definitions associated with CONFIG_DEBUG_GPIO

2016-06-15 09:20:23 -06:00

kinetis

Kinetis I2C: Review and extend I2C register definitions for K40 and K60

2016-08-16 12:17:23 -06:00

kl

Merged in JordanMacIntyre/nuttx/PWM_driver (pull request #106 )

2016-07-25 14:59:45 -06:00

lpc11xx

Rename LP11xx version of CONFIG_GPIO_IRQ to CONFIG_LPC11_GPIOIRQ

2016-07-22 14:23:31 -06:00

lpc17xx

Rename LP17xx version of CONFIG_GPIO_IRQ to CONFIG_LPC17_GPIOIRQ

2016-07-22 14:18:30 -06:00

lpc31xx

Without lowsyslog() *llinfo() is not useful. Eliminate and replace with *info().

2016-06-20 11:59:15 -06:00

lpc43xx

There are some small problems in LPC43xx RS485 mode configuration. In particular: 1. UART0,2,3 do not have DTR pins (different from UART1), so, Kconfig needs to be adjusted. 2. lpc43_uart.c in RS485 mode only configures DIR pin, but doesn't enable pin output for UART0,2,3. 3. should be option to reverse DIR control pin output polarity. 4. lpc43xx/chip/lpc43_uart.h doesn't have USART3 definitions. NOTE: I didn't modified and didn't tested USART1, as it has different hardware. From Vytautas Lukenskas.

2016-09-30 08:51:49 -06:00

lpc214x

Fix names of pre-processor variables used in header file idempotence

2016-08-06 18:48:45 -06:00

lpc2378

Fix names of pre-processor variables used in header file idempotence

2016-08-06 18:48:45 -06:00

moxart

Change *err() to either info() or err(ERROR:..), depending upon if an error has occurred.

2016-06-16 16:30:45 -06:00

nuc1xx

Without lowsyslog() *llinfo() is not useful. Eliminate and replace with *info().

2016-06-20 11:59:15 -06:00

sam34

SAM GPIO: Apply Wolfgang's change for SAM3/4 to SAMA5 and SAMV7

2016-09-20 15:33:31 -06:00

sama5

SAM GPIO: Apply Wolfgang's change for SAM3/4 to SAMA5 and SAMV7

2016-09-20 15:33:31 -06:00

samdl

Missed a few *llinfo() to *info() conversions

2016-06-20 16:24:09 -06:00

samv7

SAM GPIO: Apply Wolfgang's change for SAM3/4 to SAMA5 and SAMV7

2016-09-20 15:33:31 -06:00

stm32

dma2d: fix an error in up_dma2dcreatelayer where an invalid pointer was returned when a certain underlying function failed.

2016-10-07 13:42:24 +02:00

stm32f7

Remove GPIO_ETH_RMII_TX_CLK. TX_CLK is not present in RMII

2016-09-22 10:05:45 +02:00

stm32l4

Fixed L4 USB Driver by avoiding SETUPDONE and EPOUT_SETUP

2016-10-04 16:52:12 -10:00

str71x

Remove lowsyslog(). The new syslog() includes all of the functionality of lowsyslog(). No longer any need for two interfaces.

2016-06-20 08:57:08 -06:00

tiva

Add a new ioctl command (set MAXPOS) for tiva QEI

2016-09-26 18:10:06 +08:00

tms570

Without lowsyslog() *llerr() is not useful. Eliminate and replace with *err().

2016-06-20 12:44:38 -06:00

.gitignore

Remove the arch/ subdirectory; replace it with a submodule

2015-07-22 10:56:22 -06:00

Makefile

All GCC final arch/*/src/Makefiles: Allow --start-group and --end-group to be redefined for the case where GCC is used to link (instead of LD). Suggested by Paul Alexander Patience.

2016-05-17 10:43:15 -06:00