| .. |
|
a1x
|
Without lowsyslog() *llerr() is not useful. Eliminate and replace with *err().
|
2016-06-20 12:44:38 -06:00 |
|
arm
|
Replaces last three commits. Does the same thing, but does it in a way that does not change the usage model.
|
2016-06-21 05:26:08 -06:00 |
|
armv6-m
|
Replaces last three commits. Does the same thing, but does it in a way that does not change the usage model.
|
2016-06-21 05:26:08 -06:00 |
|
armv7-a
|
All CMP platforms: Apply same fix verified on other platforms found on Xtensa.
|
2016-12-21 14:04:09 -06:00 |
|
armv7-m
|
All CMP platforms: Apply same fix verified on other platforms found on Xtensa.
|
2016-12-21 14:04:09 -06:00 |
|
armv7-r
|
For Cortex-A9, should also set ACTLR.FW in SMP mode to enble TLB and cache broadcasts. Does not fix SMP cache problem.
|
2016-12-07 09:06:41 -06:00 |
|
c5471
|
Eliminate CONFIG_NO_NOINTS. Lots of files changed -> lots of testing needed.
|
2016-12-03 16:28:19 -06:00 |
|
common
|
i.MX6: Remove non-cached, inter-cpu memory region. Not a useful concept.
|
2016-12-13 16:59:50 -06:00 |
|
dm320
|
Fix names of pre-processor variables used in header file idempotence
|
2016-08-06 18:48:45 -06:00 |
|
efm32
|
EFM32: Fix a compilation error
|
2016-12-07 09:13:13 -06:00 |
|
imx1
|
arch: Disable priority inheritance on all semaphores used for signaling in all SPI drivers
|
2016-11-03 14:51:44 -06:00 |
|
imx6
|
i.MX6: Remove non-cached, inter-cpu memory region. Not a useful concept.
|
2016-12-13 16:59:50 -06:00 |
|
kinetis
|
Eliminate CONFIG_NO_NOINTS. Lots of files changed -> lots of testing needed.
|
2016-12-03 16:28:19 -06:00 |
|
kl
|
Remove minnsh configurations and support logic: up_getc() and lowinstream.
|
2016-12-13 18:01:23 -06:00 |
|
lpc11xx
|
Remove minnsh configurations and support logic: up_getc() and lowinstream.
|
2016-12-13 18:01:23 -06:00 |
|
lpc17xx
|
Back out most of 46dbbe837e. The order is correct -- or, rather, the order is the same as the order that response data is provided. Change the order will break all other drivers.
|
2016-12-15 07:16:24 -06:00 |
|
lpc31xx
|
arch: Disable priority inheritance on all semaphores used for signaling in all USB host drivers
|
2016-11-03 17:05:53 -06:00 |
|
lpc43xx
|
LPC43xx SD card: Correct pin configuration options needed for SD card pins.
|
2016-12-09 10:54:17 -06:00 |
|
lpc214x
|
Fix names of pre-processor variables used in header file idempotence
|
2016-08-06 18:48:45 -06:00 |
|
lpc2378
|
arch: Disable priority inheritance on all semaphores used for signaling in all I2C/TWI drivers
|
2016-11-03 14:23:42 -06:00 |
|
moxart
|
Change *err() to either info() or err(ERROR:..), depending upon if an error has occurred.
|
2016-06-16 16:30:45 -06:00 |
|
nuc1xx
|
Without lowsyslog() *llinfo() is not useful. Eliminate and replace with *info().
|
2016-06-20 11:59:15 -06:00 |
|
sam34
|
Fix some SMP-related compilation errors
|
2016-12-09 17:10:59 -06:00 |
|
sama5
|
SAMA5 PWM: Minor improvement to a loop
|
2016-12-04 15:48:13 -06:00 |
|
samdl
|
Missed a few *llinfo() to *info() conversions
|
2016-06-20 16:24:09 -06:00 |
|
samv7
|
SAMV7: MCAN: Prevent Interrupt-Flooding of ACKE when not connected to CAN-BUS. An Acknowledge-Error will occur every time no other CAN Node acknowledges the message sent. This will also occur if the device is not connected to the can-bus. The CAN-Standard declares, that the Chip has to retry a given message as long as it is not sent successfully (or it is not cancelled by the application). Every time the chip tries to resend the message an Acknowledge-Error-Interrupt is generated. At high baud rates this can lead in extremely high CPU load just for handling the interrupts (and possibly the error handling in the application). To prevent this Interrupt-Flooding we disable the ACKE once it is seen as long we didn't transfer at least one message successfully.
|
2016-12-13 11:22:54 -06:00 |
|
stm32
|
STM32: Fix some STM32F7 copy paste errors
|
2016-12-17 08:31:12 -06:00 |
|
stm32f7
|
Typo in stm32f76xx77xx_pinmap.h edited online with Bitbucket
|
2016-12-09 15:53:58 +00:00 |
|
stm32l4
|
STM32L4: Correct USART1/2 definitions. Use default mbed UART4 settings
|
2016-12-01 09:00:59 -06:00 |
|
str71x
|
Remove lowsyslog(). The new syslog() includes all of the functionality of lowsyslog(). No longer any need for two interfaces.
|
2016-06-20 08:57:08 -06:00 |
|
tiva
|
Review of last PR
|
2016-12-20 07:08:46 -06:00 |
|
tms570
|
Without lowsyslog() *llerr() is not useful. Eliminate and replace with *err().
|
2016-06-20 12:44:38 -06:00 |
|
.gitignore
|
Remove the arch/ subdirectory; replace it with a submodule
|
2015-07-22 10:56:22 -06:00 |
|
Makefile
|
Back out part of previous commit
|
2016-11-03 08:57:55 -06:00 |
