a1c991d921
Move boards to boards folder
* boards: rename configs folder to boards
This is the proposed layout after the change:
boards: - folder containing board folders
<board>: - name of each board
drivers: - extra drivers specific for platform
include: - header files for the boars
scripts: - extra scripts specific for platform
src: - board specific code
tools: - extra tools specific for platform
<config>: - board specific configuration(s)
Note:
<xxx> names are dependent on platform
This is a logical change to aim to the arch layout but this is a
huge change it should be done in several steps to lower the risk.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Kconfig: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile.*: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Make.defs: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .sh: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .mk: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .c & .h: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .bat: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
40 lines
1.1 KiB
Plaintext
40 lines
1.1 KiB
Plaintext
README.txt
|
|
^^^^^^^^^^
|
|
|
|
OSTEST Project
|
|
--------------
|
|
|
|
ostest.zfpproj is a simple ZDS II - ZNEO 5.0.1 project that will allow you
|
|
to use the ZDS-II debugger. Before using, copy the following files from
|
|
the toplevel directory:
|
|
|
|
nuttx.hex, nuttx.map, nuttx.lod
|
|
|
|
to this directory as:
|
|
|
|
ostest.hex, ostest.map, ostest.lod
|
|
|
|
Loading and Executing Code
|
|
--------------------------
|
|
|
|
1. Copy the files to this directory as described above
|
|
2. Connect the ZiLOG XTools USB debugger.
|
|
3. Install the USB driver from the ZDS-II device_drivers directory
|
|
4. Start ZDS-II and load the ostest.zfpproj project
|
|
5. In the debug tab, connect to the debugger
|
|
6. In the debug tab, load code, reset, and go
|
|
|
|
Hmmm... it appears that the code does not run if started by a hardware reset.
|
|
It runs only when started via the debugger. What is up with that?
|
|
|
|
Console Output
|
|
--------------
|
|
|
|
OS test results will be provided on the serial console at 57600 8N1 baud.
|
|
|
|
STATUS
|
|
------
|
|
|
|
This exemple works fine when started from ZDS-II. But I have seen problems
|
|
when starting from a hardware reset.
|