David Sidrane f078a2496b drivers/serial/serial_io.c: Uses signal numbers, but does not include signal.h. This has not problems but missing signal definitions have been seen in certain cases.		2019-11-04 16:24:41 -06:00
..
Kconfig	This commit brings in the drivers needed to support OpenAMP. These changes were ported from https://github.com/FishsemiCode/nuttx. The current state: Most drivers do now compile but are not yet verfied.	2019-11-02 11:30:33 -06:00
Kconfig-16550	Squashed commit of the following:	2018-08-26 11:37:16 -06:00
Kconfig-lpuart	This commit implements RS485 RX/TX switching and RTS/CTS flow control for the IMXRT family. It has been tested on 1020 but I don't see any reason for issues on any other family member.	2019-05-30 13:45:36 -06:00
Kconfig-sci	We have ported NuttX on Renesas RX65N Micro-controller. This port includes following interfaces	2019-10-11 23:36:57 +08:00
Kconfig-uart	drivers/serial/Kconfig: Kconfig is too big, divide into Kconfig, Kconfig-uart, Kconfig-usart, Kconfig-sci, Kconfig-16550. More than one MCU supports LPUARTs. Add Kconfig-lpuart and remove MCU-specific LPUART definitions. Affects Kinetis and STM32L4.	2018-03-14 10:33:27 -06:00
Kconfig-usart	drivers/serial/Kconfig: Kconfig is too big, divide into Kconfig, Kconfig-uart, Kconfig-usart, Kconfig-sci, Kconfig-16550. More than one MCU supports LPUARTs. Add Kconfig-lpuart and remove MCU-specific LPUART definitions. Affects Kinetis and STM32L4.	2018-03-14 10:33:27 -06:00
lowconsole.c	Squashed commit of the following:	2019-05-21 18:57:54 -06:00
Make.defs	This commit brings in the drivers needed to support OpenAMP. These changes were ported from https://github.com/FishsemiCode/nuttx. The current state: Most drivers do now compile but are not yet verfied.	2019-11-02 11:30:33 -06:00
ptmx.c	Squashed commit of the following:	2019-05-21 18:57:54 -06:00
pty.c	Squashed commit of the following:	2019-05-21 18:57:54 -06:00
pty.h	PTY: Add ioctls to support locking and unlocking of the slave. LIBC: Add implementation of unlockpt()	2016-07-15 09:39:33 -06:00
serial_dma.c	drivers/serial: The upper half serial driver configuration CONFIG_SERIAL_DMA used to enable DMA on both RX and TX streams. This was replaced with CONFIG_SERIAL_RXDMA and CONFIG_SERIAKL_TXDMA which will permit supporting DMA on only one or both streams.	2019-04-24 12:11:40 -06:00
serial_io.c	drivers/serial/serial_io.c: Uses signal numbers, but does not include signal.h. This has not problems but missing signal definitions have been seen in certain cases.	2019-11-04 16:24:41 -06:00
serial.c	drivers/serial/serial.c: Only real uart will call pm_activity().	2019-11-03 19:56:28 -06:00
tcdrain.c	Make sure that labeling is used consistently in all function headers (part 2).	2018-02-01 12:03:55 -06:00
uart_16550.c	drivers/serial: The upper half serial driver configuration CONFIG_SERIAL_DMA used to enable DMA on both RX and TX streams. This was replaced with CONFIG_SERIAL_RXDMA and CONFIG_SERIAKL_TXDMA which will permit supporting DMA on only one or both streams.	2019-04-24 12:11:40 -06:00
uart_rpmsg.c	This commit brings in the drivers needed to support OpenAMP. These changes were ported from https://github.com/FishsemiCode/nuttx. The current state: Most drivers do now compile but are not yet verfied.	2019-11-02 11:30:33 -06:00