nuttx/boards/arm/stm32/nucleo-f303ze/include/board.h

/****************************************************************************
 * boards/arm/stm32/nucleo-f303ze/include/board.h
 *
 * Licensed to the Apache Software Foundation (ASF) under one or more
 * contributor license agreements.  See the NOTICE file distributed with
 * this work for additional information regarding copyright ownership.  The
 * ASF licenses this file to you under the Apache License, Version 2.0 (the
 * "License"); you may not use this file except in compliance with the
 * License.  You may obtain a copy of the License at
 *
 *   http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
 * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
 * License for the specific language governing permissions and limitations
 * under the License.
 *
 ****************************************************************************/

#ifndef __BOARDS_ARM_STM32_NUCLEOF303ZE_INCLUDE_BOARD_H
#define __BOARDS_ARM_STM32_NUCLEOF303ZE_INCLUDE_BOARD_H

/****************************************************************************
 * Included Files
 ****************************************************************************/

#include <nuttx/config.h>

#ifndef __ASSEMBLY__
#  include <stdint.h>
#  include <stdbool.h>
#endif

#ifdef __KERNEL__
#  include "stm32.h"
#endif

/****************************************************************************
 * Pre-processor Definitions
 ****************************************************************************/

/* Clocking *****************************************************************/

/* HSI - Internal 8 MHz RC Oscillator
 * LSI - 32 KHz RC
 * HSE - 8 MHz from MCO output of ST-LINK
 * LSE - 32.768 kHz
 */

#define STM32_BOARD_XTAL        8000000ul        /* X1 on board */

#define STM32_HSEBYP_ENABLE
#define STM32_HSI_FREQUENCY     8000000ul
#define STM32_LSI_FREQUENCY     40000            /* Between 30kHz and 60kHz */
#define STM32_HSE_FREQUENCY     STM32_BOARD_XTAL
#define STM32_LSE_FREQUENCY     32768            /* X2 on board */

/* PLL source is HSE/1, PLL multipler is 9:
 *   PLL frequency is 8MHz (XTAL) x 9 = 72MHz
 */

#define STM32_CFGR_PLLSRC       RCC_CFGR_PLLSRC
#define STM32_CFGR_PLLXTPRE     0
#define STM32_CFGR_PLLMUL       RCC_CFGR_PLLMUL_CLKx9
#define STM32_PLL_FREQUENCY     (9*STM32_BOARD_XTAL)

/* Use the PLL and set the SYSCLK source to be the PLL */

#define STM32_SYSCLK_SW         RCC_CFGR_SW_PLL
#define STM32_SYSCLK_SWS        RCC_CFGR_SWS_PLL
#define STM32_SYSCLK_FREQUENCY  STM32_PLL_FREQUENCY

/* AHB clock (HCLK) is SYSCLK (72MHz) */

#define STM32_RCC_CFGR_HPRE     RCC_CFGR_HPRE_SYSCLK
#define STM32_HCLK_FREQUENCY    STM32_SYSCLK_FREQUENCY

/* APB2 clock (PCLK2) is HCLK (72MHz) */

#define STM32_RCC_CFGR_PPRE2    RCC_CFGR_PPRE2_HCLK
#define STM32_PCLK2_FREQUENCY   STM32_HCLK_FREQUENCY
#define STM32_APB2_CLKIN        (STM32_PCLK2_FREQUENCY)   /* Timers 1 and 8, 15-17 */

/* APB2 timers 1 and 8, 15-17 will receive PCLK2. */

/* Timers driven from APB2 will be PCLK2 */

#define STM32_APB2_TIM1_CLKIN   (STM32_PCLK2_FREQUENCY)
#define STM32_APB2_TIM8_CLKIN   (STM32_PCLK2_FREQUENCY)
#define STM32_APB1_TIM15_CLKIN  (STM32_PCLK2_FREQUENCY)
#define STM32_APB1_TIM16_CLKIN  (STM32_PCLK2_FREQUENCY)
#define STM32_APB1_TIM17_CLKIN  (STM32_PCLK2_FREQUENCY)

/* APB1 clock (PCLK1) is HCLK/2 (36MHz) */

#define STM32_RCC_CFGR_PPRE1    RCC_CFGR_PPRE1_HCLKd2
#define STM32_PCLK1_FREQUENCY   (STM32_HCLK_FREQUENCY/2)

/* APB1 timers 2-7 will be twice PCLK1 */

#define STM32_APB1_TIM2_CLKIN   (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM3_CLKIN   (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM4_CLKIN   (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM6_CLKIN   (2*STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM7_CLKIN   (2*STM32_PCLK1_FREQUENCY)

/* USB divider -- Divide PLL clock by 1.5 */

#define STM32_CFGR_USBPRE       0

/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx
 * otherwise frequency is 2xAPBx.
 * Note: TIM1,8 are on APB2, others on APB1
 */

#define BOARD_TIM1_FREQUENCY   STM32_HCLK_FREQUENCY
#define BOARD_TIM2_FREQUENCY   (STM32_HCLK_FREQUENCY / 2)
#define BOARD_TIM3_FREQUENCY   (STM32_HCLK_FREQUENCY / 2)
#define BOARD_TIM4_FREQUENCY   (STM32_HCLK_FREQUENCY / 2)
#define BOARD_TIM5_FREQUENCY   (STM32_HCLK_FREQUENCY / 2)
#define BOARD_TIM6_FREQUENCY   (STM32_HCLK_FREQUENCY / 2)
#define BOARD_TIM7_FREQUENCY   (STM32_HCLK_FREQUENCY / 2)
#define BOARD_TIM8_FREQUENCY   STM32_HCLK_FREQUENCY

/* LED definitions **********************************************************/

/* The Nucleo-144 board has numerous LEDs but only three, LD1 a Green LED,
 * LD2 a Blue LED and LD3 a Red LED, that can be controlled by software.
 * The following definitions assume the default Solder Bridges are installed.
 *
 * If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs
 * in any way.
 * The following definitions are used to access individual LEDs.
 */

/* LED index values for use with board_userled() */

#define BOARD_LED1        0
#define BOARD_LED2        1
#define BOARD_LED3        2
#define BOARD_NLEDS       3

#define BOARD_LED_GREEN   BOARD_LED1
#define BOARD_LED_BLUE    BOARD_LED2
#define BOARD_LED_RED     BOARD_LED3

/* LED bits for use with board_userled_all() */

#define BOARD_LED1_BIT    (1 << BOARD_LED1)
#define BOARD_LED2_BIT    (1 << BOARD_LED2)
#define BOARD_LED3_BIT    (1 << BOARD_LED3)

/* If CONFIG_ARCH_LEDS is defined, the usage by the board port is defined in
 * include/board.h and src/stm32_leds.c. The LEDs are used to encode
 * OS-related events as follows:
 *
 *
 *   SYMBOL                     Meaning                      LED state
 *                                                        Red   Green Blue
 *   ----------------------  --------------------------  ------ ------ ----
 */

#define LED_STARTED        0 /* NuttX has been started   OFF    OFF   OFF  */
#define LED_HEAPALLOCATE   1 /* Heap has been allocated  OFF    OFF   ON   */
#define LED_IRQSENABLED    2 /* Interrupts enabled       OFF    ON    OFF  */
#define LED_STACKCREATED   3 /* Idle stack created       OFF    ON    ON   */
#define LED_INIRQ          4 /* In an interrupt          N/C    N/C   GLOW */
#define LED_SIGNAL         5 /* In a signal handler      N/C    GLOW  N/C  */
#define LED_ASSERTION      6 /* An assertion failed      GLOW   N/C   GLOW */
#define LED_PANIC          7 /* The system has crashed   Blink  OFF   N/C  */
#define LED_IDLE           8 /* MCU is is sleep mode     ON     OFF   OFF  */

/* Button definitions *******************************************************/

/* The NUCLEO board supports one button:  Pushbutton B1, labeled "User", is
 * connected to GPIO PC13.  A high value will be sensed when the button is
 * depressed.
 */

#define BUTTON_USER      0
#define NUM_BUTTONS      1

#define BUTTON_USER_BIT  (1 << BUTTON_USER)

/* Alternate function pin selections ****************************************/

/* USART3 (Nucleo Virtual Console) */

#define GPIO_USART3_RX     GPIO_USART3_RX_3  /* PD9 */
#define GPIO_USART3_TX     GPIO_USART3_TX_3  /* PD8 */

/* I2C1 Use Nucleo I2C1 pins */

#define GPIO_I2C1_SCL GPIO_I2C1_SCL_3 /* PB8 - D15 */
#define GPIO_I2C1_SDA GPIO_I2C1_SDA_3 /* PB9 - D14 */

/* I2C2 Use Nucleo I2C2 pins */

#define GPIO_I2C2_SCL  GPIO_I2C2_SCL_2  /* PF1 - D69 */
#define GPIO_I2C2_SDA  GPIO_I2C2_SDA_2  /* PF0 - D68 */
#define GPIO_I2C2_SMBA GPIO_I2C2_SMBA_2 /* PF2 - D70 */

/* DMA **********************************************************************/

#define ADC1_DMA_CHAN DMACHAN_ADC1
#define ADC3_DMA_CHAN DMACHAN_ADC3

#endif /* __BOARDS_ARM_STM32_NUCLEO_F303ZE_INCLUDE_BOARD_H */