nuttx/arch/arm/src/stm32/stm32_i2c.c

/************************************************************************************
 * arch/arm/src/stm32/stm32_i2c.c
 *
 *   Copyright (C) 2011 Uros Platise. All rights reserved.
 *   Author: Uros Platise <uros.platise@isotel.eu>
 *
 * With extensions, modifications by:
 *
 *   Copyright (C) 2011 Gregory Nutt. All rights reserved.
 *   Author: Gregroy Nutt <gnutt@nuttx.org>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 * 3. Neither the name NuttX nor the names of its contributors may be
 *    used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 ************************************************************************************/

/* \file
 *  \author Uros Platise
 *  \brief STM32 I2C Hardware Layer - Device Driver
 * 
 * Supports:
 *  - Master operation, 100 kHz (standard) and 400 kHz (full speed)
 *  - Multiple instances (shared bus)
 *  - Interrupt based operation
 * 
 * Structure naming:
 *  - Device: structure as defined by the nuttx/i2c/i2c.h
 *  - Instance: represents each individual access to the I2C driver, obtained by
 *      the i2c_init(); it extends the Device structure from the nuttx/i2c/i2c.h; 
 *      Instance points to OPS, to common I2C Hardware private data and contains
 *      its own private data, as frequency, address, mode of operation (in the future)
 *  - Private: Private data of an I2C Hardware
 * 
 * \todo
 *  - Check for all possible deadlocks (as BUSY='1' I2C needs to be reset in HW using the I2C_CR1_SWRST)
 *  - SMBus support (hardware layer timings are already supported) and add SMBA gpio pin
 *  - Slave support with multiple addresses (on multiple instances):
 *      - 2 x 7-bit address or 
 *      - 1 x 10 bit adresses + 1 x 7 bit address (?)
 *      - plus the broadcast address (general call)
 *  - Multi-master support
 *  - DMA (to get rid of too many CPU wake-ups and interventions)
 *  - Be ready for IPMI
 **/

/************************************************************************************
 * Included Files
 ************************************************************************************/

#include <nuttx/config.h>

#include <sys/types.h>
#include <stdio.h>
#include <stdlib.h>
#include <stdint.h>
#include <stdbool.h>
#include <semaphore.h>
#include <errno.h>
#include <debug.h>

#include <nuttx/arch.h>
#include <nuttx/irq.h>
#include <nuttx/i2c.h>
#include <nuttx/kmalloc.h>
#include <nuttx/clock.h>

#include <arch/board/board.h>

#include "up_arch.h"

#include "stm32_rcc.h"
#include "stm32_i2c.h"
#include "stm32_waste.h"

#if defined(CONFIG_STM32_I2C1) || defined(CONFIG_STM32_I2C2)

/************************************************************************************
 * Pre-processor Definitions
 ************************************************************************************/
/* Configuration ********************************************************************/
/* CONFIG_I2C_POLLED may be set so that I2C interrrupts will not be used.  Instead,
 * CPU-intensive polling will be used.
 */

/* Interrupt wait timeout in seconds and milliseconds */

#if !defined(CONFIG_STM32_I2CTIMEOSEC) && !defined(CONFIG_STM32_I2CTIMEOMS)
#  define  CONFIG_STM32_I2CTIMEOSEC 0
#  define CONFIG_STM32_I2CTIMEOMS   500   /* Default is 500 milliseconds */
#elif !defined(CONFIG_STM32_I2CTIMEOSEC)
#  define  CONFIG_STM32_I2CTIMEOSEC 0     /* User provided milliseconds */
#elif !defined(CONFIG_STM32_I2CTIMEOMS)
#  define CONFIG_STM32_I2CTIMEOMS   0     /* User provided seconds */
#endif

/* Interrupt wait time timeout in system timer ticks */

#define CONFIG_STM32_I2CTIMEOTICKS \
  (SEC2TICK(CONFIG_STM32_I2CTIMEOSEC) + MSEC2TICK(CONFIG_STM32_I2CTIMEOMS))

/* Debug ****************************************************************************/
/* CONFIG_DEBUG_I2C + CONFIG_DEBUG enables general I2C debug output. */

#ifdef CONFIG_DEBUG_I2C
#  define i2cdbg dbg
#  define i2cvdbg vdbg
#else
#  define i2cdbg(x...)
#  define i2cvdbg(x...)
#endif

/* I2C event trace logic.  NOTE:  trace uses the internal, non-standard, low-level
 * debug interface lib_rawprintf() but does not require that any other debug
 * is enabled.
 */

#ifndef CONFIG_I2C_TRACE
#  define stm32_i2c_tracereset(p)
#  define stm32_i2c_tracenew(p,s)
#  define stm32_i3c_traceevent(p,e,a)
#  define stm32_i2c_tracedump(p)
#endif

#ifndef CONFIG_I2C_NTRACE
#  define CONFIG_I2C_NTRACE 20
#endif

/************************************************************************************
 * Private Types
 ************************************************************************************/
/* Interrupt state */

enum stm32_intstate_e
{
  INTSTATE_IDLE = 0,      /* No I2C activity */
  INTSTATE_WAITING,       /* Waiting for completion of interrupt activity */
  INTSTATE_DONE,          /* Interrupt activity complete */
};

/* Trace events */

enum stm32_trace_e
{
  I2CEVENT_NONE = 0,      /* No events have occurred with this status */
  I2CEVENT_SB,            /* Start/Master, param = msgc */
  I2CEVENT_SENDBYTE,      /* Send byte, param = byte sent */
  I2CEVENT_READ,          /* Read data, param = dcnt */
  I2CEVENT_ITBUFEN,       /* Enable buffer interrupts, param = 0 */
  I2CEVENT_RXNE,          /* Read more dta, param = dcnt */
  I2CEVENT_REITBUFEN,     /* Re-enable buffer interrupts, param = 0 */
  I2CEVENT_DISITBUFEN,    /* Disable buffer interrupts, param = 0 */
  I2CEVENT_BTFSTART,      /* Last byte sent, re-starting, param = msgc */
  I2CEVENT_BTFSTOP,       /* Last byte sten, send stop, param = 0 */
  I2CEVENT_ERROR          /* Error occurred, param = 0 */
};

/* Trace data */

struct stm32_trace_s
{
  uint32_t status;             /* I2C 32-bit SR2|SR1 status */
  uint32_t count;              /* Interrupt count when status change */
  enum stm32_intstate_e event; /* Last event that occurred with this status */
  uint32_t parm;               /* Parameter associated with the event */
};

/* I2C Device Private Data */

struct stm32_i2c_priv_s
{
  uint32_t    base;        /* I2C base address */
  int         refs;        /* Referernce count */
  sem_t       sem_excl;    /* Mutual exclusion semaphore */
#ifndef CONFIG_I2C_POLLED
  sem_t       sem_isr;     /* Interrupt wait semaphore */
#endif
  volatile uint8_t intstate;  /* Interrupt handshake (see enum stm32_intstate_e) */
    
  uint8_t     msgc;        /* Message count */
  struct i2c_msg_s *msgv;  /* Message list */
  uint8_t    *ptr;         /* Current message buffer */
  int         dcnt;        /* Current message length */
  uint16_t    flags;       /* Current message flags */

  /* I2C trace support */

#ifdef CONFIG_I2C_TRACE
  int         tndx;        /* Trace array index */
  uint32_t    isr_count;   /* Count of ISRs processed */
  uint32_t    old_status;  /* Last 32-bit status value */

  /* The actual trace data */

  struct stm32_trace_s trace[CONFIG_I2C_NTRACE];
#endif

  uint32_t    status;      /* End of transfer SR2|SR1 status */
};

/* I2C Device, Instance */

struct stm32_i2c_inst_s
{
  struct i2c_ops_s        *ops;  /* Standard I2C operations */
  struct stm32_i2c_priv_s *priv; /* Common driver private data structure */
    
  uint32_t    frequency;   /* Frequency used in this instantiation */
  int         address;     /* Address used in this instantiation */
  uint16_t    flags;       /* Flags used in this instantiation */
};

/************************************************************************************
 * Private Function Prototypes
 ************************************************************************************/

static inline uint16_t stm32_i2c_getreg(FAR struct stm32_i2c_priv_s *priv,
                                        uint8_t offset);
static inline void stm32_i2c_putreg(FAR struct stm32_i2c_priv_s *priv, uint8_t offset,
                                    uint16_t value);
static inline void stm32_i2c_modifyreg(FAR struct stm32_i2c_priv_s *priv,
                                       uint8_t offset, uint16_t clearbits,
                                       uint16_t setbits);
static inline void stm32_i2c_sem_wait(FAR struct i2c_dev_s *dev);
static inline int  stm32_i2c_sem_waitdone(FAR struct stm32_i2c_priv_s *priv);
static inline void stm32_i2c_sem_waitstop(FAR struct stm32_i2c_priv_s *priv);
static inline void stm32_i2c_sem_post(FAR struct i2c_dev_s *dev);
static inline void stm32_i2c_sem_init(FAR struct i2c_dev_s *dev);
static inline void stm32_i2c_sem_destroy(FAR struct i2c_dev_s *dev);
#ifdef CONFIG_I2C_TRACE
static void stm32_i2c_tracereset(FAR struct stm32_i2c_priv_s *priv);
static void stm32_i2c_tracenew(FAR struct stm32_i2c_priv_s *priv, uint32_t status);
static void stm32_i3c_traceevent(FAR struct stm32_i2c_priv_s *priv,
                               enum stm32_trace_e event, uint32_t parm);
static void stm32_i2c_tracedump(FAR struct stm32_i2c_priv_s *priv);
#endif
static void stm32_i2c_setclock(FAR struct stm32_i2c_priv_s *priv,
                               uint32_t frequency);
static inline void stm32_i2c_sendstart(FAR struct stm32_i2c_priv_s *priv);
static inline void stm32_i2c_clrstart(FAR struct stm32_i2c_priv_s *priv);
static inline void stm32_i2c_sendstop(FAR struct stm32_i2c_priv_s *priv);
static inline uint32_t stm32_i2c_getstatus(FAR struct stm32_i2c_priv_s *priv);
#if defined(CONFIG_STM32_FSMC) && defined (CONFIG_STM32_I2C1)
static inline uint32_t stm32_i2c_disablefsmc(FAR struct stm32_i2c_priv_s *priv);
static inline void stm32_i2c_enablefsmc(uint32_t ahbenr);
#endif
static int stm32_i2c_isr(struct stm32_i2c_priv_s * priv);
#ifndef CONFIG_I2C_POLLED
#ifdef CONFIG_STM32_I2C1
static int stm32_i2c1_isr(int irq, void *context);
#endif
#ifdef CONFIG_STM32_I2C2
static int stm32_i2c2_isr(int irq, void *context);
#endif
#endif
static int stm32_i2c_init(FAR struct stm32_i2c_priv_s *priv);
static int stm32_i2c_deinit(FAR struct stm32_i2c_priv_s *priv);
static uint32_t stm32_i2c_setfrequency(FAR struct i2c_dev_s *dev,
                                       uint32_t frequency);
static int stm32_i2c_setaddress(FAR struct i2c_dev_s *dev, int addr, int nbits);
static int stm32_i2c_process(FAR struct i2c_dev_s *dev, FAR struct i2c_msg_s *msgs,
                             int count);
static int stm32_i2c_write(FAR struct i2c_dev_s *dev, const uint8_t *buffer,
                          int buflen);
static int stm32_i2c_read(FAR struct i2c_dev_s *dev, uint8_t *buffer, int buflen);
#ifdef CONFIG_I2C_WRITEREAD
static int stm32_i2c_writeread(FAR struct i2c_dev_s *dev,
                               const uint8_t *wbuffer, int wbuflen,
                               uint8_t *buffer, int buflen);
#endif
#ifdef CONFIG_I2C_TRANSFER
static int stm32_i2c_transfer(FAR struct i2c_dev_s *dev, FAR struct i2c_msg_s *msgs,
                              int count);
#endif

/************************************************************************************
 * Private Data
 ************************************************************************************/

#ifdef CONFIG_STM32_I2C1
struct stm32_i2c_priv_s stm32_i2c1_priv =
{
  .base       = STM32_I2C1_BASE,
  .refs       = 0,
  .intstate   = INTSTATE_IDLE,
  .msgc       = 0,
  .msgv       = NULL,
  .ptr        = NULL,
  .dcnt       = 0,
  .flags      = 0,
  .status     = 0    
};
#endif

#ifdef CONFIG_STM32_I2C2
struct stm32_i2c_priv_s stm32_i2c2_priv =
{
  .base       = STM32_I2C2_BASE,
  .refs       = 0,
  .intstate   = INTSTATE_IDLE,
  .msgc       = 0,
  .msgv       = NULL,
  .ptr        = NULL,
  .dcnt       = 0,
  .flags      = 0,
  .status     = 0
};
#endif

/* Device Structures, Instantiation */

struct i2c_ops_s stm32_i2c_ops =
{
  .setfrequency       = stm32_i2c_setfrequency,
  .setaddress         = stm32_i2c_setaddress,
  .write              = stm32_i2c_write,
  .read               = stm32_i2c_read
#ifdef CONFIG_I2C_WRITEREAD
  , .writeread          = stm32_i2c_writeread
#endif
#ifdef CONFIG_I2C_TRANSFER
  , .transfer           = stm32_i2c_transfer
#endif
#ifdef CONFIG_I2C_SLAVE
  , .setownaddress      = stm32_i2c_setownaddress,
    .registercallback   = stm32_i2c_registercallback
#endif
};

/************************************************************************************
 * Private Functions
 ************************************************************************************/

/************************************************************************************
 * Name: stm32_i2c_getreg
 *
 * Description:
 *   Get register value by offset
 *
 ************************************************************************************/

static inline uint16_t stm32_i2c_getreg(FAR struct stm32_i2c_priv_s *priv,
                                        uint8_t offset)
{
  return getreg16(priv->base + offset);
}

/************************************************************************************
 * Name: stm32_i2c_putreg
 *
 * Description:
 *  Put register value by offset
 *
 ************************************************************************************/

static inline void stm32_i2c_putreg(FAR struct stm32_i2c_priv_s *priv, uint8_t offset,
                                    uint16_t value)
{
  putreg16(value, priv->base + offset);
}

/************************************************************************************
 * Name: stm32_i2c_modifyreg
 *
 * Description:
 *   Modify register value by offset
 *
 ************************************************************************************/

static inline void stm32_i2c_modifyreg(FAR struct stm32_i2c_priv_s *priv,
                                       uint8_t offset, uint16_t clearbits,
                                       uint16_t setbits)
{
  modifyreg16(priv->base + offset, clearbits, setbits);
}

/************************************************************************************
 * Name:
 *
 * Description:
 *
 *
 ************************************************************************************/

static inline void stm32_i2c_sem_wait(FAR struct i2c_dev_s *dev)
{
  while (sem_wait(&((struct stm32_i2c_inst_s *)dev)->priv->sem_excl) != 0)
    {
      ASSERT(errno == EINTR);
    }
}

/************************************************************************************
 * Name: stm32_i2c_sem_waitdone
 *
 * Description:
 *   Wait for a transfer to complete
 *
 ************************************************************************************/

#ifndef CONFIG_I2C_POLLED
static inline int stm32_i2c_sem_waitdone(FAR struct stm32_i2c_priv_s *priv)
{
  struct timespec abstime;
  irqstate_t flags;
  uint32_t regval;
  int ret;

  flags = irqsave();

  /* Enable I2C interrupts */

  regval  = stm32_i2c_getreg(priv, STM32_I2C_CR2_OFFSET);
  regval |= (I2C_CR2_ITERREN | I2C_CR2_ITEVFEN);
  stm32_i2c_putreg(priv, STM32_I2C_CR2_OFFSET, regval);

  /* Signal the interrupt handler that we are waiting.  NOTE:  Interrupts
   * are currently disabled but will be temporarily re-enabled below when
   * sem_timedwait() sleeps.
   */

   priv->intstate = INTSTATE_WAITING;
   do
    {
      /* Get the current time */

      (void)clock_gettime(CLOCK_REALTIME, &abstime);

      /* Calculate a time in the future */

#if CONFIG_STM32_I2CTIMEOSEC > 0
      abstime.tv_sec += CONFIG_STM32_I2CTIMEOSEC;
#endif
#if CONFIG_STM32_I2CTIMEOMS > 0
      abstime.tv_nsec += CONFIG_STM32_I2CTIMEOMS * 1000 * 1000;
      if (abstime.tv_nsec > 1000 * 1000 * 1000)
        {
          abstime.tv_sec++;
          abstime.tv_nsec -= 1000 * 1000 * 1000;
        }
#endif
      /* Wait until either the transfer is complete or the timeout expires */

      ret = sem_timedwait(&priv->sem_isr, &abstime);
      if (ret != OK && errno != EINTR)
        {
          /* Break out of the loop on irrecoverable errors.  This would
           * include timeouts and mystery errors reported by sem_timedwait.
           * NOTE that we try again if we are awakened by a signal (EINTR).
           */

          break;
        }
    }

  /* Loop until the interrupt level transfer is complete. */

  while (priv->intstate != INTSTATE_DONE);

  /* Set the interrupt state back to IDLE */

  priv->intstate = INTSTATE_IDLE;

  /* Disable I2C interrupts */

  regval  = stm32_i2c_getreg(priv, STM32_I2C_CR2_OFFSET);
  regval &= ~I2C_CR2_ALLINTS;
  stm32_i2c_putreg(priv, STM32_I2C_CR2_OFFSET, regval);

  irqrestore(flags);
  return ret;
}
#else
static inline int stm32_i2c_sem_waitdone(FAR struct stm32_i2c_priv_s *priv )
{
  uint32_t start;
  uint32_t elapsed;
  int ret;

  /* Signal the interrupt handler that we are waiting.  NOTE:  Interrupts
   * are currently disabled but will be temporarily re-enabled below when
   * sem_timedwait() sleeps.
   */

  priv->intstate = INTSTATE_WAITING;
  start = clock_systimer();
  do
    {
      /* Poll by simply calling the timer interrupt handler until it
       * reports that it is done.
       */

      stm32_i2c_isr(priv);

      /* Calculate the elapsed time */

      elapsed = clock_systimer() - start;
    }

  /* Loop until the transfer is complete. */

  while (priv->intstate != INTSTATE_DONE && elapsed < CONFIG_STM32_I2CTIMEOTICKS);

  i2cvdbg("intstate: %d elapsed: %d threshold: %d status: %08x\n",
          priv->intstate, elapsed, CONFIG_STM32_I2CTIMEOTICKS, priv->status);

  /* Set the interrupt state back to IDLE */

  ret = priv->intstate == INTSTATE_DONE ? OK : -ETIMEDOUT;
  priv->intstate = INTSTATE_IDLE;
  return ret;
}
#endif

/************************************************************************************
 * Name: stm32_i2c_sem_waitstop
 *
 * Description:
 *   Wait for a STOP to complete
 *
 ************************************************************************************/

static inline void stm32_i2c_sem_waitstop(FAR struct stm32_i2c_priv_s *priv)
{
  uint32_t start;
  uint32_t elapsed;
  uint32_t cr1;
  uint32_t sr1;

  /* Wait as stop might still be in progress; but stop might also
   * be set because of a timeout error: "The [STOP] bit is set and
   * cleared by software, cleared by hardware when a Stop condition is
   * detected, set by hardware when a timeout error is detected."
   */

  start = clock_systimer();
  do
    {
      /* Check for STOP condition */

      cr1 = stm32_i2c_getreg(priv, STM32_I2C_CR1_OFFSET);
      if ((cr1 & I2C_CR1_STOP) == 0)
        {
          return;
        }

      /* Check for timeout error */

      sr1 = stm32_i2c_getreg(priv, STM32_I2C_SR1_OFFSET);
      if ((sr1 & I2C_SR1_TIMEOUT) != 0)
        {
          return;
        }      

      /* Calculate the elapsed time */

      elapsed = clock_systimer() - start;
    }

  /* Loop until the stop is complete or a timeout occurs. */

  while (elapsed < CONFIG_STM32_I2CTIMEOTICKS);

  /* If we get here then a timeout occurred with the STOP condition
   * still pending.
   */

  i2cvdbg("Timeout with CR1: %04x SR1: %04x\n", cr1, sr1);
}

/************************************************************************************
 * Name: stm32_i2c_sem_post
 *
 * Description:
 *   Release the mutual exclusion semaphore
 *
 ************************************************************************************/

static inline void stm32_i2c_sem_post(FAR struct i2c_dev_s *dev)
{
  sem_post( &((struct stm32_i2c_inst_s *)dev)->priv->sem_excl );
}

/************************************************************************************
 * Name: stm32_i2c_sem_init
 *
 * Description:
 *   Initialize semaphores
 *
 ************************************************************************************/

static inline void stm32_i2c_sem_init(FAR struct i2c_dev_s *dev)
{
  sem_init(&((struct stm32_i2c_inst_s *)dev)->priv->sem_excl, 0, 1);
#ifndef CONFIG_I2C_POLLED
  sem_init(&((struct stm32_i2c_inst_s *)dev)->priv->sem_isr, 0, 0);
#endif
}

/************************************************************************************
 * Name: stm32_i2c_sem_destroy
 *
 * Description:
 *   Destroy semaphores.
 *
 ************************************************************************************/

static inline void stm32_i2c_sem_destroy(FAR struct i2c_dev_s *dev)
{
  sem_destroy(&((struct stm32_i2c_inst_s *)dev)->priv->sem_excl);
#ifndef CONFIG_I2C_POLLED
  sem_destroy(&((struct stm32_i2c_inst_s *)dev)->priv->sem_isr);
#endif
}

/************************************************************************************
 * Name: stm32_i2c_trace*
 *
 * Description:
 *   I2C trace instrumentation
 *
 ************************************************************************************/

#ifdef CONFIG_I2C_TRACE
static void stm32_i2c_tracereset(FAR struct stm32_i2c_priv_s *priv)
{
  /* Reset the trace info for a new data collection */

  priv->isr_count  = 0;
  priv->old_status = 0xffffffff;
  priv->tndx       = -1;
}

static void stm32_i2c_tracenew(FAR struct stm32_i2c_priv_s *priv, uint32_t status)
{
  /* Increment the cout of interrupts received */

  priv->isr_count++;

  /* Has the status changed from the last interrupt */

  if (status != priv->old_status)
    {
      /* Yes.. bump up the trace index (unless we are out of trace entries) */

      if (priv->tndx < CONFIG_I2C_NTRACE)
        {
          priv->tndx++;
        }

      /* Initialize the new trace entry */

      priv->trace[priv->tndx].status = status;
      priv->trace[priv->tndx].count  = priv->isr_count;
      priv->trace[priv->tndx].event  = I2CEVENT_NONE;
      priv->trace[priv->tndx].parm   = 0;
      priv->old_status               = status;
    }
}

static void stm32_i3c_traceevent(FAR struct stm32_i2c_priv_s *priv,
                                enum stm32_trace_e event, uint32_t parm)
{
  /* Add the event to the trace entry (possibly overwriting a previous trace
   * event.
   */
 
  priv->trace[priv->tndx].event  = event;
  priv->trace[priv->tndx].parm   = parm;
}

static void stm32_i2c_tracedump(FAR struct stm32_i2c_priv_s *priv)
{
  int i;

  /* Dump all of the buffered trace entries */

  for (i = 0; i < priv->tndx; i++)
    {
      lib_rawprintf("%2d. STATUS: %08x COUNT: %3d EVENT: %2d PARM: %08x\n", i,
                    priv->trace[i].status, priv->trace[i].count,
                    priv->trace[i].event,  priv->trace[i].parm);
    }
}
#endif /* CONFIG_I2C_TRACE */

/************************************************************************************
 * Name: stm32_i2c_setclock
 *
 * Description:
 *   Set the I2C clock
 *
 ************************************************************************************/

static void stm32_i2c_setclock(FAR struct stm32_i2c_priv_s *priv, uint32_t frequency)
{
  uint16_t cr1;
  uint16_t ccr;
  uint16_t trise;
  uint16_t freqmhz;
  uint16_t speed;

  /* Disable the selected I2C peripheral to configure TRISE */

  cr1 = stm32_i2c_getreg(priv, STM32_I2C_CR1_OFFSET);
  stm32_i2c_putreg(priv, STM32_I2C_CR1_OFFSET, cr1 & ~I2C_CR1_PE);

  /* Update timing and control registers */

  freqmhz = (uint16_t)(STM32_PCLK1_FREQUENCY / 1000000);
  ccr = 0;

  /* Configure speed in standard mode */

  if (frequency <= 100000)
    {
      /* Standard mode speed calculation */

      speed = (uint16_t)(STM32_PCLK1_FREQUENCY / (frequency << 1));

      /* The CCR fault must be >= 4 */

      if (speed < 4)
        {
          /* Set the minimum allowed value */

          speed = 4;  
        }
      ccr |= speed;

      /* Set Maximum Rise Time for standard mode */

      trise = freqmhz + 1; 
    }

  /* Configure speed in fast mode */

  else /* (frequency <= 400000) */
    {
      /* Fast mode speed calculation with Tlow/Thigh = 16/9 */

#ifdef CONFIG_I2C_DUTY16_9
      speed = (uint16_t)(STM32_PCLK1_FREQUENCY / (frequency * 25));

      /* Set DUTY and fast speed bits */

      ccr |= (I2C_CCR_DUTY|I2C_CCR_FS);
#else
      /* Fast mode speed calculation with Tlow/Thigh = 2 */

      speed = (uint16_t)(STM32_PCLK1_FREQUENCY / (frequency * 3));

      /* Set fast speed bit */

      ccr |= I2C_CCR_FS;
#endif

      /* Verify that the CCR speed value is nonzero */

      if (speed < 1)
        {
          /* Set the minimum allowed value */

          speed = 1;  
        }
      ccr |= speed;

      /* Set Maximum Rise Time for fast mode */

      trise = (uint16_t)(((freqmhz * 300) / 1000) + 1);  
    }

  /* Write the new values of the CCR and TRISE registers */

  stm32_i2c_putreg(priv, STM32_I2C_CCR_OFFSET, ccr);
  stm32_i2c_putreg(priv, STM32_I2C_TRISE_OFFSET, trise);

  /* Bit 14 of OAR1 must be configured and kept at 1 */

  stm32_i2c_putreg(priv, STM32_I2C_OAR1_OFFSET, I2C_OAR1_ONE);

  /* Re-enable the peripheral (or not) */

  stm32_i2c_putreg(priv, STM32_I2C_CR1_OFFSET, cr1);
}

/************************************************************************************
 * Name: stm32_i2c_sendstart
 *
 * Description:
 *   Send the START conditions/force Master mode
 *
 ************************************************************************************/

static inline void stm32_i2c_sendstart(FAR struct stm32_i2c_priv_s *priv)
{
  /* Disable ACK on receive by default and generate START */

  stm32_i2c_modifyreg(priv, STM32_I2C_CR1_OFFSET, I2C_CR1_ACK, I2C_CR1_START);
}

/************************************************************************************
 * Name: stm32_i2c_clrstart
 *
 * Description:
 *   Clear the STOP, START or PEC condition on certain error recovery steps.
 *
 ************************************************************************************/

static inline void stm32_i2c_clrstart(FAR struct stm32_i2c_priv_s *priv)
{
  /* "Note: When the STOP, START or PEC bit is set, the software must
   *  not perform any write access to I2C_CR1 before this bit is
   *  cleared by hardware. Otherwise there is a risk of setting a
   *  second STOP, START or PEC request."
   *
   * "The [STOP] bit is set and cleared by software, cleared by hardware
   *  when a Stop condition is detected, set by hardware when a timeout
   *  error is detected.
   * 
   * "This [START] bit is set and cleared by software and cleared by hardware
   *  when start is sent or PE=0."  The bit must be cleared by software if the
   *  START is never sent.
   *
   * "This [PEC] bit is set and cleared by software, and cleared by hardware
   *  when PEC is transferred or by a START or Stop condition or when PE=0."
   */

  stm32_i2c_modifyreg(priv, STM32_I2C_CR1_OFFSET,
                      I2C_CR1_START|I2C_CR1_STOP|I2C_CR1_PEC, 0);
}

/************************************************************************************
 * Name: stm32_i2c_sendstop
 *
 * Description:
 *   Send the STOP conditions
 *
 ************************************************************************************/

static inline void stm32_i2c_sendstop(FAR struct stm32_i2c_priv_s *priv)
{
  stm32_i2c_modifyreg(priv, STM32_I2C_CR1_OFFSET, I2C_CR1_ACK, I2C_CR1_STOP);
}

/************************************************************************************
 * Name: stm32_i2c_getstatus
 *
 * Description:
 *   Get 32-bit status (SR1 and SR2 combined)
 *
 ************************************************************************************/

static inline uint32_t stm32_i2c_getstatus(FAR struct stm32_i2c_priv_s *priv)
{
  uint32_t status = stm32_i2c_getreg(priv, STM32_I2C_SR1_OFFSET);
  status |= (stm32_i2c_getreg(priv, STM32_I2C_SR2_OFFSET) << 16);
  return status;
}

/************************************************************************************
 * Name: stm32_i2c_disablefsmc
 *
 * Description:
 *   FSMC must be disable while accessing I2C1 because it uses a common resource
 *   (LBAR)
 *
 ************************************************************************************/

#if defined(CONFIG_STM32_FSMC) && defined (CONFIG_STM32_I2C1)
static inline uint32_t stm32_i2c_disablefsmc(FAR struct stm32_i2c_priv_s *priv)
{
  uint32_t ret = 0;
  uint32_t regval;

  /* Is this I2C1 */

#ifdef CONFIG_STM32_I2C2
  if (priv->base == STM32_I2C1_BASE)
#endif
    {
      /* Disable FSMC unconditionally */

      ret    = getreg32( STM32_RCC_AHBENR);
      regval = ret & ~RCC_AHBENR_FSMCEN;
      putreg32(regval, STM32_RCC_AHBENR);
    }
  return ret;
}

/************************************************************************************
 * Name: stm32_i2c_enablefsmc
 *
 * Description:
 *   Re-enabled the FSMC
 *
 ************************************************************************************/

static inline void stm32_i2c_enablefsmc(uint32_t ahbenr)
{
  uint32_t regval;

  /* Enable AHB clocking to the FSMC only if it was previously enabled. */

  if ((ahbenr & RCC_AHBENR_FSMCEN) != 0)
    {
      regval  = getreg32( STM32_RCC_AHBENR);
      regval |= RCC_AHBENR_FSMCEN;
      putreg32(regval, STM32_RCC_AHBENR);
    }
}
#else
#  define stm32_i2c_disablefsmc(priv) (0)
#  define stm32_i2c_enablefsmc(ahbenr)
#endif

/************************************************************************************
 * Name: stm32_i2c_isr
 *
 * Description:
 *  Common Interrupt Service Routine
 *
 ************************************************************************************/

static int stm32_i2c_isr(struct stm32_i2c_priv_s * priv)
{
  uint32_t status = stm32_i2c_getstatus(priv);

  /* Check for new trace setup */

  stm32_i2c_tracenew(priv, status);
            
  /* Was start bit sent */
    
  if ((status & I2C_SR1_SB) != 0)
    {
      stm32_i3c_traceevent(priv, I2CEVENT_SB, priv->msgc);

      /* Get run-time data */

      priv->ptr   = priv->msgv->buffer;
      priv->dcnt  = priv->msgv->length;
      priv->flags = priv->msgv->flags;

      /* Send address byte and define addressing mode */

      stm32_i2c_putreg(priv, STM32_I2C_DR_OFFSET,
                      (priv->flags & I2C_M_TEN) ?
                       0 : ((priv->msgv->addr << 1) | (priv->flags & I2C_M_READ)));

      /* Set ACK for receive mode */

      if (priv->dcnt > 1 && (priv->flags & I2C_M_READ) != 0)
        {
          stm32_i2c_modifyreg(priv, STM32_I2C_CR1_OFFSET, 0, I2C_CR1_ACK);
        }

      /* Increment to next pointer and decrement message count */

      priv->msgv++;
      priv->msgc--;
    }

 /* In 10-bit addressing mode, was first byte sent */
    
  else if ((status & I2C_SR1_ADD10) != 0)
    {
      /* \todo Finish 10-bit mode addressing */
    }

  /* Was address sent, continue with ether sending or reading data */
    
  else if ((priv->flags & I2C_M_READ) == 0 && (status & (I2C_SR1_ADDR | I2C_SR1_TXE)) != 0)
    {
      stm32_i3c_traceevent(priv, I2CEVENT_READ, priv->dcnt);

      if (--priv->dcnt >= 0)
        {
          /* Send a byte */

          stm32_i3c_traceevent(priv, I2CEVENT_SENDBYTE, *priv->ptr);
          stm32_i2c_putreg(priv, STM32_I2C_DR_OFFSET, *priv->ptr++); 
        }
    }

  else if ((priv->flags & I2C_M_READ) != 0 && (status & I2C_SR1_ADDR) != 0)
    {
      /* Enable RxNE and TxE buffers in order to receive one or multiple bytes */

#ifndef CONFIG_I2C_POLLED
      stm32_i3c_traceevent(priv, I2CEVENT_ITBUFEN, 0);
      stm32_i2c_modifyreg(priv, STM32_I2C_CR2_OFFSET, 0, I2C_CR2_ITBUFEN);
#endif
    }

  /* More bytes to read */

  else if ((status & I2C_SR1_RXNE) != 0)
    {
      /* Read a byte, if dcnt goes < 0, then read dummy bytes to ack ISRs */
    
      stm32_i3c_traceevent(priv, I2CEVENT_RXNE, priv->dcnt);
      if (--priv->dcnt >= 0)
        {
          *priv->ptr++ = stm32_i2c_getreg(priv, STM32_I2C_DR_OFFSET);

          /* Disable acknowledge when last byte is to be received */

          if (priv->dcnt == 1)
            {
              stm32_i2c_modifyreg(priv, STM32_I2C_CR1_OFFSET, I2C_CR1_ACK, 0);  
            }
        }
    }
    
  /* Do we have more bytes to send, enable/disable buffer interrupts
   * (these ISRs could be replaced by DMAs)
   */

#ifndef CONFIG_I2C_POLLED
  if (priv->dcnt > 0)
    {
      stm32_i3c_traceevent(priv, I2CEVENT_REITBUFEN, 0);
      stm32_i2c_modifyreg(priv, STM32_I2C_CR2_OFFSET, 0, I2C_CR2_ITBUFEN);
    }
  else if (priv->dcnt == 0)
    {
      stm32_i3c_traceevent(priv, I2CEVENT_DISITBUFEN, 0);
      stm32_i2c_modifyreg(priv, STM32_I2C_CR2_OFFSET, I2C_CR2_ITBUFEN, 0);  
    }
#endif
    
  /* Was last byte received or sent?  */

  if (priv->dcnt <= 0 && (status & I2C_SR1_BTF) != 0)
    {
      stm32_i2c_getreg(priv, STM32_I2C_DR_OFFSET);    /* ACK ISR */

      /* Do we need to terminate or restart after this byte?
       * If there are more messages to send, then we may:
       *
       *  - continue with repeated start
       *  - or just continue sending writeable part
       *  - or we close down by sending the stop bit 
       */

      if (priv->msgc > 0)
        {
          stm32_i3c_traceevent(priv, I2CEVENT_BTFSTART, priv->msgc);
          if (priv->msgv->flags & I2C_M_NORESTART)
            {
              priv->ptr   = priv->msgv->buffer;
              priv->dcnt  = priv->msgv->length;
              priv->flags = priv->msgv->flags;
              priv->msgv++;
              priv->msgc--;

              /* Restart this ISR! */

#ifndef CONFIG_I2C_POLLED
              stm32_i2c_modifyreg(priv, STM32_I2C_CR2_OFFSET, 0, I2C_CR2_ITBUFEN);
#endif
            }
          else
            {
              stm32_i2c_sendstart(priv);
            }
        }
      else if (priv->msgv)
        {
          stm32_i3c_traceevent(priv, I2CEVENT_BTFSTOP, 0);
          stm32_i2c_sendstop(priv);

          /* Is there a thread waiting for this event (there should be) */

#ifndef CONFIG_I2C_POLLED
          if (priv->intstate == INTSTATE_WAITING)
            {
              /* Yes.. inform the thread that the transfer is complete
               * and wake it up.
               */

              sem_post( &priv->sem_isr );
              priv->intstate = INTSTATE_DONE;
            }
#else
          priv->intstate = INTSTATE_DONE;
#endif

          /* Mark that we have stopped with this transaction */

          priv->msgv = NULL;
        }
    }
    
    /* Check for errors, in which case, stop the transfer and return 
     * Note that in master reception mode AF becomes set on last byte
     * since ACK is not returned. We should ignore this error.
     */
    
    if ((status & I2C_SR1_ERRORMASK) != 0)
      {
        stm32_i3c_traceevent(priv, I2CEVENT_ERROR, 0);

        /* Clear interrupt flags */

        stm32_i2c_putreg(priv, STM32_I2C_SR1_OFFSET, 0);

        /* Is there a thread waiting for this event (there should be) */

#ifndef CONFIG_I2C_POLLED
        if (priv->intstate == INTSTATE_WAITING)
          {
              /* Yes.. inform the thread that the transfer is complete
               * and wake it up.
               */

            sem_post( &priv->sem_isr );
            priv->intstate = INTSTATE_DONE;
          }
#else
        priv->intstate = INTSTATE_DONE;
#endif
    }

    priv->status = status;
    return OK;
}

/************************************************************************************
 * Name: stm32_i2c1_isr
 *
 * Description:
 *   I2C1 interrupt service routine
 *
 ************************************************************************************/

#ifndef CONFIG_I2C_POLLED
#ifdef CONFIG_STM32_I2C1
static int stm32_i2c1_isr(int irq, void *context)
{
  return stm32_i2c_isr(&stm32_i2c1_priv);
}
#endif

/************************************************************************************
 * Name: stm32_i2c2_isr
 *
 * Description:
 *   I2C2 interrupt service routine
 *
 ************************************************************************************/

#ifdef CONFIG_STM32_I2C2
static int stm32_i2c2_isr(int irq, void *context)
{
  return stm32_i2c_isr(&stm32_i2c2_priv);
}
#endif
#endif

/************************************************************************************
 * Private Initialization and Deinitialization
 ************************************************************************************/

/************************************************************************************
 * Name: stm32_i2c_init
 *
 * Description:
 *   Setup the I2C hardware, ready for operation with defaults
 *
 ************************************************************************************/

static int stm32_i2c_init(FAR struct stm32_i2c_priv_s *priv)
{
  /* Power-up and configure GPIOs */

  switch (priv->base)
    {
#ifdef CONFIG_STM32_I2C1
      case STM32_I2C1_BASE:

        /* Enable power and reset the peripheral */

        modifyreg32(STM32_RCC_APB1ENR, 0, RCC_APB1ENR_I2C1EN);

        modifyreg32(STM32_RCC_APB1RSTR, 0, RCC_APB1RSTR_I2C1RST);
        modifyreg32(STM32_RCC_APB1RSTR, RCC_APB1RSTR_I2C1RST, 0);

        /* Configure pins */
            
        if (stm32_configgpio(GPIO_I2C1_SCL) < 0)
          {
            return ERROR;
          }

        if (stm32_configgpio(GPIO_I2C1_SDA) < 0)
          {
            stm32_unconfiggpio(GPIO_I2C1_SCL);
            return ERROR;
          }

        /* Attach ISRs */
            
#ifndef CONFIG_I2C_POLLED
        irq_attach(STM32_IRQ_I2C1EV, stm32_i2c1_isr);
        irq_attach(STM32_IRQ_I2C1ER, stm32_i2c1_isr);
        up_enable_irq(STM32_IRQ_I2C1EV);
        up_enable_irq(STM32_IRQ_I2C1ER);
#endif
        break;
#endif
      
#ifdef CONFIG_STM32_I2C2
      case STM32_I2C2_BASE:

        /* Enable power and reset the peripheral */

        modifyreg32(STM32_RCC_APB1ENR, 0, RCC_APB1ENR_I2C2EN);

        modifyreg32(STM32_RCC_APB1RSTR, 0, RCC_APB1RSTR_I2C2RST);
        modifyreg32(STM32_RCC_APB1RSTR, RCC_APB1RSTR_I2C2RST, 0);

        /* Configure pins */

        if (stm32_configgpio(GPIO_I2C2_SCL) < 0)
          {
            return ERROR;
          }

        if (stm32_configgpio(GPIO_I2C2_SDA) < 0)
          {
            stm32_unconfiggpio(GPIO_I2C2_SCL);
            return ERROR;
          }

        /* Attach ISRs */

#ifndef CONFIG_I2C_POLLED
        irq_attach(STM32_IRQ_I2C2EV, stm32_i2c2_isr);
        irq_attach(STM32_IRQ_I2C2ER, stm32_i2c2_isr);
        up_enable_irq(STM32_IRQ_I2C2EV);
        up_enable_irq(STM32_IRQ_I2C2ER);
#endif
        break;
#endif

      default:
        return ERROR;
    }

  /* Set peripheral frequency, where it must be at least 2 MHz  for 100 kHz
   * or 4 MHz for 400 kHz.  This also disables all I2C interrupts.
   */

  stm32_i2c_putreg(priv, STM32_I2C_CR2_OFFSET, (STM32_PCLK1_FREQUENCY / 1000000));
  stm32_i2c_setclock(priv, 100000);
        
  /* Enable I2C */
    
  stm32_i2c_putreg(priv, STM32_I2C_CR1_OFFSET, I2C_CR1_PE);
  return OK;
}

/************************************************************************************
 * Name: stm32_i2c_deinit
 *
 * Description:
 *   Shutdown the I2C hardware
 *
 ************************************************************************************/

static int stm32_i2c_deinit(FAR struct stm32_i2c_priv_s *priv)
{
  /* Disable I2C */

  stm32_i2c_putreg(priv, STM32_I2C_CR1_OFFSET, 0);

  switch (priv->base)
    {
#ifdef CONFIG_STM32_I2C1
      case STM32_I2C1_BASE:
        stm32_unconfiggpio(GPIO_I2C1_SCL);
        stm32_unconfiggpio(GPIO_I2C1_SDA);

#ifndef CONFIG_I2C_POLLED
        up_disable_irq(STM32_IRQ_I2C1EV);
        up_disable_irq(STM32_IRQ_I2C1ER);
        irq_detach(STM32_IRQ_I2C1EV);
        irq_detach(STM32_IRQ_I2C1ER);
#endif
        modifyreg32(STM32_RCC_APB1ENR, RCC_APB1ENR_I2C1EN, 0);
        break;
#endif
      
#ifdef CONFIG_STM32_I2C2
      case STM32_I2C2_BASE:
        stm32_unconfiggpio(GPIO_I2C2_SCL);
        stm32_unconfiggpio(GPIO_I2C2_SDA);

#ifndef CONFIG_I2C_POLLED
        up_disable_irq(STM32_IRQ_I2C2EV);
        up_disable_irq(STM32_IRQ_I2C2ER);
        irq_detach(STM32_IRQ_I2C2EV);
        irq_detach(STM32_IRQ_I2C2ER);
#endif
        modifyreg32(STM32_RCC_APB1ENR, RCC_APB1ENR_I2C2EN, 0);
        break;
#endif
        
      default:
        return ERROR;
    }

  return OK;
}

/************************************************************************************
 * Device Driver Operations
 ************************************************************************************/

/************************************************************************************
 * Name: stm32_i2c_setfrequency
 *
 * Description:
 *   Set the I2C frequency
 *
 ************************************************************************************/

static uint32_t stm32_i2c_setfrequency(FAR struct i2c_dev_s *dev, uint32_t frequency)
{
  stm32_i2c_sem_wait(dev);

#if STM32_PCLK1_FREQUENCY < 4000000
  ((struct stm32_i2c_inst_s *)dev)->frequency = 100000;
#else
  ((struct stm32_i2c_inst_s *)dev)->frequency = frequency;
#endif

  stm32_i2c_sem_post(dev);    
  return ((struct stm32_i2c_inst_s *)dev)->frequency;
}

/************************************************************************************
 * Name: stm32_i2c_setaddress
 *
 * Description:
 *   Set the I2C slave address
 *
 ************************************************************************************/

static int stm32_i2c_setaddress(FAR struct i2c_dev_s *dev, int addr, int nbits)
{
  stm32_i2c_sem_wait(dev);

  ((struct stm32_i2c_inst_s *)dev)->address = addr;
  ((struct stm32_i2c_inst_s *)dev)->flags   = (nbits == 10) ? I2C_M_TEN : 0;

    stm32_i2c_sem_post(dev);
    return OK;
}

/************************************************************************************
 * Name: stm32_i2c_process
 *
 * Description:
 *   Common I2C transfer logic
 *
 ************************************************************************************/

static int stm32_i2c_process(FAR struct i2c_dev_s *dev, FAR struct i2c_msg_s *msgs, int count)
{
  struct stm32_i2c_inst_s     *inst = (struct stm32_i2c_inst_s *)dev;
  FAR struct stm32_i2c_priv_s *priv = inst->priv;
  uint32_t    status = 0;
  uint32_t    ahbenr;
  int         errval = 0;

  ASSERT(count);

  /* Disable FSMC that shares a pin with I2C1 (LBAR) */

  ahbenr = stm32_i2c_disablefsmc(priv);

  /* Wait for any STOP in progress.  NOTE:  If we have to disable the FSMC
   * then we cannot do this at the top of the loop, unfortunately.  The STOP
   * will not complete normally if the FSMC is enabled.
   */

#if !defined(CONFIG_STM32_FSMC) || !defined (CONFIG_STM32_I2C1)
  stm32_i2c_sem_waitstop(priv);
#endif

  /* Clear any pending error interrupts */

  stm32_i2c_putreg(priv, STM32_I2C_SR1_OFFSET, 0);

  /* "Note: When the STOP, START or PEC bit is set, the software must
   *  not perform any write access to I2C_CR1 before this bit is
   *  cleared by hardware. Otherwise there is a risk of setting a
   *  second STOP, START or PEC request."  However, if the bits are
   *  not cleared by hardware, then we will have to do that from hardware.
   */

  stm32_i2c_clrstart(priv);
    
  /* Old transfers are done */

  priv->msgv = msgs;
  priv->msgc = count;

  /* Reset I2C trace logic */

  stm32_i2c_tracereset(priv);
        
  /* Set I2C clock frequency (on change it toggles I2C_CR1_PE !) */

  stm32_i2c_setclock(priv, inst->frequency);

  /* Trigger start condition, then the process moves into the ISR.  I2C
   * interrupts will be enabled within stm32_i2c_waitdone().
   */

  priv->status = 0;
  stm32_i2c_sendstart(priv);

  /* Wait for an ISR, if there was a timeout, fetch latest status to get
   * the BUSY flag.
   */

  if (stm32_i2c_sem_waitdone(priv) < 0)
    {
      status = stm32_i2c_getstatus(priv);
      errval = ETIMEDOUT;

      i2cdbg("Timed out: CR1: %04x status: %08x\n",
             stm32_i2c_getreg(priv, STM32_I2C_CR1_OFFSET), status);

      /* "Note: When the STOP, START or PEC bit is set, the software must
       *  not perform any write access to I2C_CR1 before this bit is
       *  cleared by hardware. Otherwise there is a risk of setting a
       *  second STOP, START or PEC request."
       */

      stm32_i2c_clrstart(priv);
    }
  else
    {
      /* clear SR2 (BUSY flag) as we've done successfully */

      status = priv->status & 0xffff;
    }

  /* Check for error status conditions */

  if ((status & I2C_SR1_ERRORMASK) != 0)
    {
      /* I2C_SR1_ERRORMASK is the 'OR' of the following individual bits: */

      if (status & I2C_SR1_BERR)
        {
          /* Bus Error */

          errval = EIO;
        }
      else if (status & I2C_SR1_ARLO)
        {
          /* Arbitration Lost (master mode) */

          errval = EAGAIN;
        }
      else if (status & I2C_SR1_AF)
        {
          /* Acknowledge Failure */

          errval = ENXIO;
        }
      else if (status & I2C_SR1_OVR)
        {
          /* Overrun/Underrun */

          errval = EIO;
        }
      else if (status & I2C_SR1_PECERR)
        {
          /* PEC Error in reception */

          errval = EPROTO;
        }
      else if (status & I2C_SR1_TIMEOUT)
        {
          /* Timeout or Tlow Error */

          errval = ETIME;
        }

      /* This is not an error and should never happen since SMBus is not enabled */

      else /* if (status & I2C_SR1_SMBALERT) */
        {
          /* SMBus alert is an optional signal with an interrupt line for devices
           * that want to trade their ability to master for a pin.
           */

          errval = EINTR;
        }
    }

  /* This is not an error, but should not happen.  The BUSY signal can hang,
   * however, if there are unhealthy devices on the bus that need to be reset.
   * NOTE:  We will only see this buy indication if stm32_i2c_sem_waitdone()
   * fails above;  Otherwise it is cleared.
   */

  else if ((status & (I2C_SR2_BUSY << 16)) != 0)
    {
      /* I2C Bus is for some reason busy */

      errval = EBUSY;
    }

  /* Dump the trace result */

  stm32_i2c_tracedump(priv);
        
  /* Wait for any STOP in progress.  NOTE:  If we have to disable the FSMC
   * then we cannot do this at the top of the loop, unfortunately.  The STOP
   * will not complete normally if the FSMC is enabled.
   */

#if defined(CONFIG_STM32_FSMC) && defined (CONFIG_STM32_I2C1)
  stm32_i2c_sem_waitstop(priv);
#endif

  /* Re-enable the FSMC */

  stm32_i2c_enablefsmc(ahbenr);
  stm32_i2c_sem_post(dev);

  return -errval;
}

/************************************************************************************
 * Name: stm32_i2c_write
 *
 * Description:
 *   Write I2C data
 *
 ************************************************************************************/

static int stm32_i2c_write(FAR struct i2c_dev_s *dev, const uint8_t *buffer, int buflen)
{
  stm32_i2c_sem_wait(dev);   /* ensure that address or flags don't change meanwhile */

  struct i2c_msg_s msgv =
  {
    .addr   = ((struct stm32_i2c_inst_s *)dev)->address,
    .flags  = ((struct stm32_i2c_inst_s *)dev)->flags,
    .buffer = (uint8_t *)buffer,
    .length = buflen
  };

  return stm32_i2c_process(dev, &msgv, 1);
}

/************************************************************************************
 * Name: stm32_i2c_read
 *
 * Description:
 *   Read I2C data
 *
 ************************************************************************************/

int stm32_i2c_read(FAR struct i2c_dev_s *dev, uint8_t *buffer, int buflen)
{
  stm32_i2c_sem_wait(dev);   /* ensure that address or flags don't change meanwhile */

  struct i2c_msg_s msgv =
  {
    .addr   = ((struct stm32_i2c_inst_s *)dev)->address,
    .flags  = ((struct stm32_i2c_inst_s *)dev)->flags | I2C_M_READ,
    .buffer = buffer,
    .length = buflen
  };
    
  return stm32_i2c_process(dev, &msgv, 1);
}

/************************************************************************************
 * Name: stm32_i2c_writeread
 *
 * Description:
 *  Read then write I2C data
 *
 ************************************************************************************/

#ifdef CONFIG_I2C_WRITEREAD
static int stm32_i2c_writeread(FAR struct i2c_dev_s *dev,
                               const uint8_t *wbuffer, int wbuflen,
                               uint8_t *buffer, int buflen)
{
  stm32_i2c_sem_wait(dev);   /* ensure that address or flags don't change meanwhile */

  struct i2c_msg_s msgv[2] =
  {
    {
      .addr   = ((struct stm32_i2c_inst_s *)dev)->address,
      .flags  = ((struct stm32_i2c_inst_s *)dev)->flags,
      .buffer = (uint8_t *)wbuffer,          /* this is really ugly, sorry const ... */
      .length = wbuflen
    },
    {
      .addr   = ((struct stm32_i2c_inst_s *)dev)->address,
      .flags  = ((struct stm32_i2c_inst_s *)dev)->flags | ((buflen>0) ? I2C_M_READ : I2C_M_NORESTART),
      .buffer = buffer,
      .length = (buflen>0) ? buflen : -buflen
    }
  };

  return stm32_i2c_process(dev, msgv, 2);
}
#endif

/************************************************************************************
 * Name: stm32_i2c_transfer
 *
 * Description:
 *   Generic I2C transfer function
 *
 ************************************************************************************/

#ifdef CONFIG_I2C_TRANSFER
static int stm32_i2c_transfer(FAR struct i2c_dev_s *dev, FAR struct i2c_msg_s *msgs,
                              int count)
{
  stm32_i2c_sem_wait(dev);   /* ensure that address or flags don't change meanwhile */
  return stm32_i2c_process(dev, msgs, count);
}
#endif

/************************************************************************************
 * Public Functions
 ************************************************************************************/

/************************************************************************************
 * Name: up_i2cinitialize
 *
 * Description:
 *   Initialize one I2C bus
 *
 ************************************************************************************/

FAR struct i2c_dev_s *up_i2cinitialize(int port)
{
  struct stm32_i2c_priv_s * priv = NULL;  /* private data of device with multiple instances */
  struct stm32_i2c_inst_s * inst = NULL;  /* device, single instance */
  int irqs;

#if STM32_PCLK1_FREQUENCY < 4000000
#   warning STM32_I2C_INIT: Peripheral clock must be at least 4 MHz to support 400 kHz operation.
#endif

#if STM32_PCLK1_FREQUENCY < 2000000
#   warning STM32_I2C_INIT: Peripheral clock must be at least 2 MHz to support 100 kHz operation.
    return NULL;
#endif
    
  /* Get I2C private structure */

  switch (port)
    {
#ifdef CONFIG_STM32_I2C1
      case 1:
        priv = (struct stm32_i2c_priv_s *)&stm32_i2c1_priv;
        break;
#endif
#ifdef CONFIG_STM32_I2C2
      case 2:
        priv = (struct stm32_i2c_priv_s *)&stm32_i2c2_priv;
        break;
#endif
      default:
        return NULL;
    }

  /* Allocate instance */
    
  if (!(inst = kmalloc( sizeof(struct stm32_i2c_inst_s))))
    {
      return NULL;
    }

  /* Initialize instance */

  inst->ops       = &stm32_i2c_ops;
  inst->priv      = priv;
  inst->frequency = 100000;
  inst->address   = 0;
  inst->flags     = 0;

  /* Init private data for the first time, increment refs count,
   * power-up hardware and configure GPIOs. 
   */
    
  irqs = irqsave();
    
  if ((volatile int)priv->refs++ == 0)
    {
      stm32_i2c_sem_init( (struct i2c_dev_s *)inst );
      stm32_i2c_init( priv );
    }
    
  irqrestore(irqs);
  return (struct i2c_dev_s *)inst;
}

/************************************************************************************
 * Name: up_i2cuninitialize
 *
 * Description:
 *   Uninitialize an I2C bus
 *
 ************************************************************************************/

int up_i2cuninitialize(FAR struct i2c_dev_s * dev)
{
  int irqs;
    
  ASSERT(dev);
    
  /* Decrement refs and check for underflow */
    
  if (((struct stm32_i2c_inst_s *)dev)->priv->refs == 0) 
    {
      return ERROR;
    }

  irqs = irqsave();

  if (--((struct stm32_i2c_inst_s *)dev)->priv->refs)
    {
      irqrestore(irqs);
      kfree(dev);
      return OK;
    }

  irqrestore(irqs);

  /* Disable power and other HW resource (GPIO's) */

  stm32_i2c_deinit( ((struct stm32_i2c_inst_s *)dev)->priv );

  /* Release unused resources */

  stm32_i2c_sem_destroy( (struct i2c_dev_s *)dev );

  kfree(dev);
  return OK;
}

#endif /* defined(CONFIG_STM32_I2C1) && defined(CONFIG_STM32_I2C2) */