The eZ80F92 interrupt controller is very different from the eZ80F91. The eZ80F91 has:
1. Four byte interrupt vectors
2. The vector base address register is 16-bit so the vector table can lie in RAM
Whereas the eZ80F92 has:
1. Two byte interrupt vectors
2. An 8-bit vector base address
This means that the vectors must lie in the first 16-bits of FLASH and there must be a "trampoline" to get to interrupt handlers outside of the first 64-Kb of FLASH.
arch/z80/src/ez80/Toolchain.defs: Correct some CFLAGS when optimization suppressed.
arch/z80/src/ez80/Kconfig arch/z80/src/ez80/ez80_emac.c: Remove configuration option for selecting EMAC RAM address. This is duplicated and possibly conflicting. The correct address for the RAM is provided in the linker command file. The RAM should be configured once and using this single definitions.
arch/z80/src/ez80/ez80_startup.asm and arch/z80/src/ez80/ez80f9*_init.asm. Move RAM and FLAH intialization out of MCU-specific logic to common start-up logic. We cannot call any functions until SRAM is initialized and the stack is properly initialized because the return address is stored on the stack. Use internal SRAM for the IDLE stack to avoid the chicken'n'egg problem.
boards/z80/ez80/z20x/configs/sdboot/sdboot.zdsproj: Discuss build environments.
These makefiles set the the ZiLOG runtime libraries for the eZ80 parts. The setup was, however, conditioned on CONFIG_ARCH_EZ80_EZ80F91 and, so, was not working for the eZ80F92 part (CONFIG_ARCH_EZ80_EZ80F92).
With this change, the z20x board FINALLY builds and links correctly with no errors.
Don't use MCU selection from compiler. It appears that we must compile ez80f92 code as ez80f91 so the comiler MCU selection is incorrect. Instead, use the selected CPU part from the configuration.
arch/z80/src/ez80/Toolchain.defs: Update some CFLAGS to match CFLAGS from ZDS-II IDE. Apparently, we must say that the CPU is an eZ80F91 event when compiler for eZ80F92.
boards/z80/ez80/z20x: Update linker scripts.
* tools/zds/zds_Config.mk: Move boards/z80/ez80/scripts/eZ80_Config.mk to tools/zds/zds_Config.mk where it can be shared by other ZDS-II platforms.
* boards/z16/z16f: Duplicate changes for new ZDS-II support from ez80
* boards/z80/z8: Duplicate changes for new ZDS-II support from ez80
* arch/z16/src/z16f/Toolchain.defs: Create required Toolchain.defs file for Z16f
There are cases that USE_SERIALDRIVER is defined but USE_EARLYSERIALINIT not defined in some configs. So use ifdef USE_EARLYSERIALINIT to include up_earlyserialinit anyway.
An error was introduced from:
commit f982ee43db
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
Date: Tue Feb 18 09:55:04 2020 +0800
drivers/serial: Remove the lowconsole driver
Replace with the syslog console driver which has more capability than lowconsole
arch/z80/arc/ez80/Toolchain.sh: Move more common toolchain definitions from Make.defs.
boards/z80/ez80/scripts/eZ80_Config.mk: Move common defines that override tools/Config.mk to this new file.
This does not solve the ez80 build problem yet but does assure that when the solution is in place, it will automatically apply to all present and future ez80 configurations.
I was over-zealous in arch/z80/src/ez80/ez80f91_handlers.asm. I added space separatros around the '+' operators. Turns out that the ZDS-II assembler can't handle the spaces in that context.
The ez80f92 is similar to the currently supported ez80f91 except that is:
1. Has no PLL and has a maximum CPU frequency of only 20MHz
2. Has no Ethernet controller
3. Timers are different
4. Has no GPIO Port A
5. Timers are different
6. It comes in a smaller package
and other small differences.
This provided the architecture (only) support for the forthcoming z20x port.
* arch/arm/src/tiva/Make.defs: Compile only when enabled by configuration CONFIG_ARM_SEMIHOSTING_HOSTFS
* arch/arm/src/common/up_hostfs.c: Remove the ifdef conditional because it's redundant with the make logic.
Largely copy-and-paste from stm32f4discovery.
Also arch/arm/src/armv7-m/mpu.h: Ensure RBAR alignment
Fix crashes on init task startup I observed on qemu-system-arm -M lm3s6965evb.
And remove syslog_init_e because all initialization is later now and we don't
distinguish the initialition phase anymore after ramlog don't need special
initialize.
