Polarfire Icicle board has only (128K - 256) bytes for the bootloader
in the non-volatile eNVM. This space is barely enough for running NuttX.
If OpenSBI is selected, it will be placed in DDR. This all means the
nuttx.bin file grows into gigabyte size, filling the unused space (ddr -
envm) with zeroes.
The memory layout is as follows:
MEMORY
{
ddr (rx) : ORIGIN = 0x80000000, LENGTH = 4M
envm (rx) : ORIGIN = 0x20220100, LENGTH = 128K - 256
l2lim (rwx) : ORIGIN = 0x08000000, LENGTH = 1024k
l2zerodevice (rwx) : ORIGIN = 0x0A000000, LENGTH = 512k
}
OpenSBI library is used as a separate binary, which is stored into
eMMC or SD-card. It is then loaded into its precise location in DDR.
Thus, we separate OpenSBI from NuttX and end up with two images
by utilizing the objcopy options:
--only-section=sectionpattern (-j in short)
--remove-section=sectionpattern (-R in short)
This is only valid when CONFIG_MPFS_OPENSBI is set.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
since VNC server is very useful even without NX:
1.Replace nxgl_coord_t with fb_coord_t
2.Replace nxgl_rect_s with fb_area_s
3.Remove nxgl_xxx function call
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Summary:
- I noticed that most of nsh commands are disabled by default
due to the recent changes for CONFIG_MM_SMALL=y in apps.
- This commit re-enables some nsh commands.
Impact:
- None
Testing:
- Tested with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Some incompatibilities exist between the encryption block of the SPI
Flash peripheral and the algorithms of some file systems. LittleFS is
currently the only supported file system which is known to work
correctly when Flash Encryption is enabled.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Add a pinmap header for mpfs to be able to configure MSSIO GPIOs
This also adds Kconfigs for some different chip/package types of the PolarFire SOC
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This fixes problems with DDR training sequence on aries m100pfs board
- Set LIBERO_SETTING_RPC_ODT_* to 6, which matches 40 ohm. Originally it was 120 ohm (2)
- Set BCLKSCLK_OFFSET value to 5, which matches icicle board setting
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
1. Fix the issue that Wi-Fi can't connect to some special routers occasionally.
2. Update Wi-Fi driver code to fix issue of failure to send pkt.
3. Replace software random with hardware random
since all NX and VNC initialization should be initiated from
user space through BOARDIOC_NX_START and BOARDIOC_VNC_START
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Update the cache settings for the Aries m100pfsevp board. This
assigns scratchpad ways for this board as well, as seen in the
commit 491ae6c.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
OpenSBI may be compiled as an external library. OpenSBI commit d249d65
(Dec. 11, 2021) needs to be reverted as it causes memcpy / memcmp to
end up in the wrong section. That issue has yet no known workaround.
OpenSBI may be lauched from the hart0 (e51). It will start the U-Boot
and eventually the Linux kernel on harts 1-4.
OpenSBI, once initialized properly, will trap and handle illegal
instructions (for example, CSR time) and unaligned address accesses
among other things.
Due to size size limitations for the mpfs eNVM area where the NuttX
is located, we actually set up the OpenSBI on its own section which
is in the bottom of the DDR memory. Special care must be taken so that
the kernel doesn't override the OpenSBI. For example, the Linux device
tree may reserve some space from the beginning:
opensbi_reserved: opensbi@80000000 {
reg = <0x80000000 0x200000>;
label = "opensbi-reserved";
};
The resulting nuttx.bin file is very large, but objcopy is used to
create the final binary images for the regions (eNVM and DDR) using
the nuttx elf file.
Co-authored-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Assign ways to L2 zerodevice. L2 zero device is used for
the scratchpad functionality. The area may be used for the
harts communicating to each other.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Move MCUboot bootloader implementation to samv7 common folder. This drop
all duplicated code and unify implementation.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This introduce common folder structre and rework scripts & tools
files. The linker scripts were reorganized to use best the current
infrastructure which uses a template to create a final samv7.ld
file based in the current SoC memories and bootloader definitions.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
After define memory sizes for samv7 it is possible unify linker scripts.
This add necessary changes to perform such operation.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Current samv7 platform does not define SoC memories sizes. This define
both internal flash and sram memories sizes and update all defconfig
files.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
1. If CONFIG_SCHED_INSTRUMENTATION_SWITCH is enabled, then these additional interfaces are expected:
sched_note_suspend
sched_note_resume
at the same time，If CONFIG_SMP is enabled，then expected：
sched_note_cpu_pause
sched_note_cpu_paused
sched_note_cpu_resume
sched_note_cpu_resumed
2. other board if enable SCHED_INSTRUMENTATION，SCHED_INSTRUMENTATION_SWITCH to defconfig.
Summary:
- This commits adjusts the following settings for spresense
- CONFIG_FAT_MAXFNAME : 255 to 128
- CONFIG_NAME_MAX : 765 to 128
Impact:
- None
Testing:
- Tested with spresense:wifi_smp
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
