This commit adds support to autoleds and userleds for
raspberrypi-pico board. It uses the board LED connected
to GPIO 25.
Signed-off-by: Alan C. Assis <acassis@gmail.com>
- remove read-write logic - this should be handled by radio protocol implementation
- remove EVENTS and TASKS bit definitions - we can just use a signle definition
- add more radio ops
- fix frequency configuration
- fix printf warnings
- fix radio reset
Simply the config, later we can directly use macro SIM_RPMSG_MASTER
to controll all the rpmsg transport init.
Signed-off-by: Bowen Wang <wangbowen6@xiaomi.com>
since clock_t may map to either 32-bit or 64-bit integer type,
UINT_MAX may not be the maximum value of clock_t.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Inclusion of mach/mach_time.h by libcxx/src/chrono.cpp breaks
the build on latest MACOS dues to https://forums.developer.apple.com/forums/thread/746737
The interface from mach/mach_time.h is not referenced in chrono.cpp
so it is safe to remove it
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
I noticed when executing pwm STOP command in
multichannel mode, the channel still outputting.
This commit fixes this issue.
Signed-off-by: Alan C. Assis <acassis@gmail.com>
I noticed when executing pwm STOP command in
multichannel mode, the channel still outputting.
This commit fixes this issue.
Signed-off-by: Alan C. Assis <acassis@gmail.com>
I noticed when executing pwm STOP command in
multichannel mode, the channel still outputting.
This commit fixes this issue.
Signed-off-by: Alan C. Assis <acassis@gmail.com>
This patch revises `k230_hart.[ch]` by:
- revising big core boot/stop control.
- making k230_hart_is_big() available in S-mode.
- adding more comments.
This patch also revises the `ld-kernel.script` so that to match the
latest MMU pgtable design.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
There have been errors like below on macOS for sim:libcxxtest
```
Error: /Applications/Xcode.../include/mach/vm_page_size.h:59:44:
error: expected ';' after top level declarator
```
This patch tries to disable that check on macOS.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This adds initial document for using TMPFS based on my short experience,
hoping to save people's time on guessing how to use.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
"
I used
cd nuttx
cmake -B build -DBOARD_CONFIG=stm32f401rc-rs485:nsh -GNinja
to config
and when following the instruction in this official websites I found the
command to use cmake to build the target is wrong.
which is "cmake --build build -t menuconfig" also wrong the output dir
"build/nuttx".
and by the way, In my practice I find the bin file and elf file is not
in build/nuttx but in build/. So I changed these. But I'm not 100% sure
that my fix is right as I'm a beginner, but what I fix works fine in my
computer. This is my first PR to the public doc. My fix maybe totally
wrong as I am not get into the nuttx, just following the instruction and
encountered some mistakes.
thx for reviewing
"
K230 chip has two T-Head C908 RiscV cores, previously we run NuttX
on either little or big cores. This patch runs NuttX on both cores
with OpenAMP support via the RPTUN driver.
New additions:
- in arch/risc-v/src/k230
- k230_rptun.c K230 RPTUN driver
- k230_rptun.h K230 RPTUN driver header file
- in baords/risc-v/k230/canmv230
- configs/master Build config for master node
- configs/remote Build config for remote node
- scripts/ld-rptun.script Build script for RPTUN
Major changes:
- arch/risc-v/Kconfig Select NUTTSBI_LATE_INIT upon NUTTSBI
- in arch/risc-v/include
- k230/irq.h Add UART3 IRQ defs
- in arch/risc-v/src/k230
- Kconfig Add RPTUN related config items
- Make.defs Add k230-rptun.c to sources
- hardware/k230_memorymap.h Add K230 device and CSR defs
- k230_hart.c Add hart ctrl for RPTUN
- k230_hart.h Add hart ctrl for RPTUN
- k230_mm_init.c Add Svpmbt to support RPTUN
- k230_start.c Revised to support RPMsg UART
- in boards/risc-v/k230/canmv230
- scripts/Make.defs Add RPTUN script selection
- src/canmv_init.c Add RPTUN and RPMsg_UART initialization
- in Documentation/platforms/risc-v/k230/boards/canmv230
- index.rst Add AMP usage information.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
It seems that RPMSGFS is missed from the list that doesn't need block or
MTD drivers. This attempts to add it.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
rpmsg_ping.c is blocking CI checks for RPTUN related patches like #11673.
this patch simply fix the compilation issue of rpmsg_ping.c:
- line 191: overflow conversion from "long unsigned int" to "unsigned int"
- line 226: "sendlen" used uninitialized
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
I recently imported NuttX version 6.0 (and nsh) into a Microchip
Studio project [1] on Windows to figure out what was going wrong with
the avr32dev1 build. I also briefly checked NuttX version 10.
I worked with the assumption that the avr32 (avr32dev1) specific
changes to the codebase were minimal across NuttX releases.
For the initial proof of concept I used Microchip Studio version 7.0
(with the recent Microchip's ASF updates). I use avr32-gcc (4.4.7)
hosted here [2] for building NuttX for avr32dev1 on GNU/Linux.
Even with the Microchip Studio project, I had initial debug problems
with just stepping through the code a line at a time. I had to bring
in crt0, a trampoline stub and the linker file from one of my older
projects to really build on the suspicion I had with the linker file.
Perhaps an older version of avr32-gcc did something differently. I am
not sure about this. I used avr32-objdump to see the output sections
of the generated elf file. I just had to tweak the linker script to
ensure correct linking of the sections.
With those changes, I was able to inspect the UART sections within
NuttX Microchip Studio project.
Second important change: the transmit pin: I had to reassign the pin
to see the nsh console.
These are the currently assigned UART pins:
RX: PA_24 -> Physical IC pin 59
TX: PB_02 -> Physical IC pin 24
For the avr32dev1 board, they are pins: J1 (berg pin 28) and J2 (berg
pin 10).
In addition, the PR fixes silly compilation problems with avr32dev1.
I have tested the nsh build with my avr32dev1 boards. I used Atmel ICE
to program one of them (flash at 0x80000000) and dfu-programmer to
test my other board (flash at 0x80002000). The other RS-232 parameters
are the same as they were.
References:
[1]: https://github.com/ramangopalan/nuttx_avr32dev1
[2]: https://github.com/ramangopalan/avr32-gnu-toolchain-linux_x86_64
ALT1250 driver sends an event named LTE_CMDID_RESTARTAPI
to ALT1250 daemon when state is PM_NOARMAL in the function
of prepare registered by pm_register.
SAMv7 reset controller stores the cause of last reset (SW reset, power up,
pin reset etc.) in status register. This commit adds function that allows
the board to retrieve this information. This function should be called
from board support layer either during initialization or based on
incoming ioctl call.
Adding the sam_get_reset_cause() to sam_systemreset.c also resulted in
always compiling this file by default and only putting up_systemreset()
under CONFIG_SAMV7_SYSTEMRESET option.
Also header file sam_systemreset.h was created as it defines reset types
in comfortable manner for future processing in board layer. This is done
to avoid passing boardctl dependent structure to architecture layer.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
