reason:
1 On different architectures, we can utilize more optimized strategies
to implement up_current_regs/up_set_current_regs.
eg. use interrupt registersor percpu registers.
code size
before
text data bss dec hex filename
262848 49985 63893 376726 5bf96 nuttx
after
text data bss dec hex filename
262844 49985 63893 376722 5bf92 nuttx
size change -4
Configuring NuttX and compile:
$ ./tools/configure.sh -l qemu-armv8a:nsh_smp
$ make
Running with qemu
$ qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic \
-machine virt,virtualization=on,gic-version=3 \
-net none -chardev stdio,id=con,mux=on -serial chardev:con \
-mon chardev=con,mode=readline -kernel ./nuttx
Signed-off-by: hujun5 <hujun5@xiaomi.com>
Intel CET (Control-flow Enforcement Technology) is a hardware enhancement aimed at mitigating the Retpoline vulnerability, but it may impact CPU branch prediction performance. This commit added ARCH_INTEL64_DISABLE_CET, which can disable CET completely with compilation option `-fcf-protection=none`.
Signed-off-by: ouyangxiangzhen <ouyangxiangzhen@xiaomi.com>
It was discovered that attempting to load x86-64 format ELF files with a multiboot1 header using the qemu `-kernel` command would result in an error, as multiboot1 only allows x86-32 format ELF files. To address this limitation, we have developed a simple x86_32 bootloader. This bootloader is designed to copy the `nuttx.bin` file to the designated memory address (`0x100000`) and then transfer control to NuttX by executing a jump instruction (`jmp 0x100000`).
Signed-off-by: ouyangxiangzhen <ouyangxiangzhen@xiaomi.com>
These are changes to make HPET work with ACRN hypervisor:
- FSB interrupt delivery (which works like PCI MSI)
- 32-bit mode support
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
TX clock or ref clock can be driven either from outside (PHY / oscilator) or by the ENET block.
Typical connection with RMII PHY is that the PHY drives the refclk.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
New configuration IMX9_HAVE_ATF_FIRMWARE introduced,
it is default on and it selects ARM64_HAVE_PSCI, when compiling
bootloader or when using bootloader that does not have atf
this shall be disabled
Signed-off-by: Jouni Ukkonen <jouni.ukkonen@unikie.com>
Using the HLT instruction in VM usually traps into the Hypervisor and releases CPU control. This will result in real-time performance degradation. Using the NOP or MWAIT instruction for an IDLE loop can reduce energy consumption while not trapping into the Hypervisor.
Signed-off-by: ouyangxiangzhen <ouyangxiangzhen@xiaomi.com>
Clean up the interrupt-driven logic in the driver; handle error cases properly,
remove dead code and simplify logic.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Change "DMACH_HANDLE *handle" into "DMACH_HANDLE handle". The DMACH_HANDLE is already
defined as "void *".
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
currently esp32 protected mode requires a patched bootloader.
it's a bit cumbersome to build the bootloader for that purpose.
this commit attempts to remove the need of the patched bootloader
by applying the changes by ourselves using esp hal.
Using the ts/tick conversion functions provided in clock.h
Do this caused we want speed up the time calculation, so change:
clock_time2ticks, clock_ticks2time, clock_timespec_add,
clock_timespec_compare, clock_timespec_subtract... to MACRO
Signed-off-by: ligd <liguiding1@xiaomi.com>
Enforcing the default 48-bit VA for everyone also implies a 4 page table
translation system. However, if less than 40 bits are needed, a full
translation table level can be dropped, making the translations faster.
Thus, make this into a configurable option, instead of enforcing the same
address widht for everyone.
Attempt to service all interrupts pending in the PLIC's claim register. Ideally, this is more efficient than switching context for each interrupt received.
Provides two implementations:
- CSR_CYCLE: Cores which implement hardware performance monitoring.
- CSR_TIME: Uses the machine time registers.
Using the up_perf_xx bindings directory is more efficient than performing a nanosecond conversion on every gettime event.
There is a tiny possibility that when a process is started a trap is
taken which causes a context switch. This moves the kernel stack
unexpectedly and the task start logic no longer works.
Fix this by recording the initial context location, and use that to
trampoline into the user process with interrupts disabled. This ensures
the context stays intact AND the kernel stack is fully unwound before
the user process starts.
This patch unifies the extended context save/restore for RISC-V,
allowing the customized context save/restore to be used, for example,
the extended context in rv32m1.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
The register context is not needed, the original idea was to provide
the user stack pointer for signal handler delivery, but the user stack
can be obtained via sp_el0 so the context registers are not needed.
SP0 is not stored upon exception entry anyways, so this code is just
completely redundant and wrong.
reason:
In SMP, when a context switch occurs, restore_critical_section is executed.
To reduce the time taken for context switching, we directly pass the required
parameters to restore_critical_section instead of acquiring them repeatedly.
Signed-off-by: hujun5 <hujun5@xiaomi.com>
The vaddr field in TLBI means: Bits[55:12] of the virtual address to match.
This basically means the page offset of the virtual address, so the input
vaddr must be shifted to the page offset.
Reference TLBI VALE1IS register description from ARMv8-A reference manual.
The 12:0 bits in table descriptors are RES0 and AF is the 10th bit, so
it is not valid to set it in this case.
Fix this by moving AF to the common MMU_MT_NORMAL_FLAGS field
Make sure the user L1 page is updated to system memory when the kernel
mappings are copied.
Also, flush the I-cache when switching address environments.
The libmad and libmp3lame libraries have been ported to
apps/audioutils and will be compiled with NuttX.
Signed-off-by: shizhenghui <shizhenghui@xiaomi.com>
