reason:
Currently, if we need to schedule a task to another CPU, we have to completely halt the other CPU,
manipulate the scheduling linked list, and then resume the operation of that CPU. This process is both time-consuming and unnecessary.
During this process, both the current CPU and the target CPU are inevitably subjected to busyloop.
The improved strategy is to simply send a cross-core interrupt to the target CPU.
The current CPU continues to run while the target CPU responds to the interrupt, eliminating the certainty of a busyloop occurring.
Signed-off-by: hujun5 <hujun5@xiaomi.com>
The aforementioned functions can/will fail if the C compiler decides
to use the stack for the incoming entrypt/etc. parameters.
Fix this issue by converting the jump to user part into pure assembly,
ensuring the stack is NOT used for the parameters.
The original code made the incorrect assumption that the amount of
translation levels is 3, but this is incorrect. The amount of levels is 4
and the amount of levels that are utilized / in use is set dynamically
from the amount of VA bits in use.
The VMSAv8-64 translation system has 4 page table levels in total, ranging
from 0-3. The address environment code assumes only 3 levels, from 1-3 but
this is wrong; the amount of levels _utilized_ depends on the configured
VA size CONFIG_ARM64_VA_BITS. With <= 39 bits 3 levels is enough, while
if the va range is larger, the 4th translation table level is taken into
use dynamically by shifting the base translation table level.
From arm64_mmu.c, where va_bits is the amount of va bits used in address
translations:
(va_bits <= 21) - base level 3
(22 <= va_bits <= 30) - base level 2
(31 <= va_bits <= 39) - base level 1
(40 <= va_bits <= 48) - base level 0
The base level is what is configured as the page directory root. This also
affects the performance of address translations i.e. if the VA range is
smaller, address translations are also faster as the page table walk is
shorter.
1. Similar to asan, supports single byte out of bounds detection
2. Fix the script to address the issue of not supporting the big end
Signed-off-by: wangmingrong1 <wangmingrong1@xiaomi.com>
1. Tested on QEMU, the two sockets were basically the same, and their performance was not affected. The size of the generated bin file was also the same
2. Extract global detection as a separate file, both types of Kasan support global variable out of bounds detection simultaneously
Signed-off-by: wangmingrong1 <wangmingrong1@xiaomi.com>
Revert "Parallelize depend file generation"
This reverts commit d5b6ec450f.
parallel depend ddc does not significantly speed up compilation,
intermediately generated .ddc files can cause problems if compilation is interrupted unexpectedly
Signed-off-by: xuxin19 <xuxin19@xiaomi.com>
reason:
1 On different architectures, we can utilize more optimized strategies
to implement up_current_regs/up_set_current_regs.
eg. use interrupt registersor percpu registers.
code size
before
text data bss dec hex filename
262848 49985 63893 376726 5bf96 nuttx
after
text data bss dec hex filename
262844 49985 63893 376722 5bf92 nuttx
size change -4
Configuring NuttX and compile:
$ ./tools/configure.sh -l qemu-armv8a:nsh_smp
$ make
Running with qemu
$ qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic \
-machine virt,virtualization=on,gic-version=3 \
-net none -chardev stdio,id=con,mux=on -serial chardev:con \
-mon chardev=con,mode=readline -kernel ./nuttx
Signed-off-by: hujun5 <hujun5@xiaomi.com>
TX clock or ref clock can be driven either from outside (PHY / oscilator) or by the ENET block.
Typical connection with RMII PHY is that the PHY drives the refclk.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
New configuration IMX9_HAVE_ATF_FIRMWARE introduced,
it is default on and it selects ARM64_HAVE_PSCI, when compiling
bootloader or when using bootloader that does not have atf
this shall be disabled
Signed-off-by: Jouni Ukkonen <jouni.ukkonen@unikie.com>
Clean up the interrupt-driven logic in the driver; handle error cases properly,
remove dead code and simplify logic.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Change "DMACH_HANDLE *handle" into "DMACH_HANDLE handle". The DMACH_HANDLE is already
defined as "void *".
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Enforcing the default 48-bit VA for everyone also implies a 4 page table
translation system. However, if less than 40 bits are needed, a full
translation table level can be dropped, making the translations faster.
Thus, make this into a configurable option, instead of enforcing the same
address widht for everyone.
There is a tiny possibility that when a process is started a trap is
taken which causes a context switch. This moves the kernel stack
unexpectedly and the task start logic no longer works.
Fix this by recording the initial context location, and use that to
trampoline into the user process with interrupts disabled. This ensures
the context stays intact AND the kernel stack is fully unwound before
the user process starts.
The register context is not needed, the original idea was to provide
the user stack pointer for signal handler delivery, but the user stack
can be obtained via sp_el0 so the context registers are not needed.
SP0 is not stored upon exception entry anyways, so this code is just
completely redundant and wrong.
reason:
In SMP, when a context switch occurs, restore_critical_section is executed.
To reduce the time taken for context switching, we directly pass the required
parameters to restore_critical_section instead of acquiring them repeatedly.
Signed-off-by: hujun5 <hujun5@xiaomi.com>
The vaddr field in TLBI means: Bits[55:12] of the virtual address to match.
This basically means the page offset of the virtual address, so the input
vaddr must be shifted to the page offset.
Reference TLBI VALE1IS register description from ARMv8-A reference manual.
The 12:0 bits in table descriptors are RES0 and AF is the 10th bit, so
it is not valid to set it in this case.
Fix this by moving AF to the common MMU_MT_NORMAL_FLAGS field
Make sure the user L1 page is updated to system memory when the kernel
mappings are copied.
Also, flush the I-cache when switching address environments.
Make this_cpu is arch independent and up_cpu_index do that.
In AMP mode, up_cpu_index() may return the index of the physical core.
Signed-off-by: fangxinyong <fangxinyong@xiaomi.com>
In corner case, the pending ISR will be triggered immediately
after enable the IRQ, this PR will setting CPU affinity first
to avoid routing the unexpected IRQ to other CPUs.
Signed-off-by: chao an <anchao@lixiang.com>
